CET PMC-53A User Manual

PMC-53A

Intelligent Multifunction Meter

User Manual

Version: V1.2A

September 12, 2018

CET Electric Technology

This manual may not be reproduced in whole or in part by any means without the express written permission from CET Inc. (CET). The information contained in this manual is believed to be accurate at the time of publication; however, CET assumes no responsibility for any errors which may appear here and reserves the right to make changes without notice. Please consult CET or your local representative for the latest product specifications.

Standards Compliance

DANGER

This symbol indicates the presence of danger that may result in severe injury or death and permanent equipment damage if proper precautions are not taken during the installation, operation or maintenance of the device.

CAUTION

This symbol indicates the potential of personal injury or equipment damage if proper precautions are not taken during the installation, operation or maintenance of the device.

2

Installation, operation and maintenance of the meter should only be performed by qualified, competent personnel that have the appropriate training and experience with high voltage and current devices. The meter must

Ensure that all incoming AC power and other power sources are turned OFF

Before connecting the meter to the power source, check the label on top of the meter to ensure that it is equipped with the appropriate power supply, and

During normal operation of the meter, hazardous voltages are present on its terminal strips and throughout the connected potential transformers (PT) and current transformers (CT). PT and CT secondary circuits are capable of

generating lethal voltages and currents with their primary circuits energized.

Follow standard safety precautions while performing any installation or service

Do not use the meter for primary protection functions where failure of the device can cause fire, injury or death. The meter should only be used for

Under no circumstances should the meter be connected to a power source if

To prevent potential fire or shock hazard, do not expose the meter to rain or

Setup procedures must be performed only by qualified personnel familiar with

DANGER

Failure to observe the following instructions may result in severe injury or death and/or equipment damage.



be installed in accordance with all local and national electrical codes.



before performing any work on the meter.



the correct voltage and current input specifications for your application.

CET Electric Technology



work (i.e. removing PT fuses, shorting CT secondaries, …etc).



shadow protection if needed.



it is damaged.



moisture.



the instrument and its associated electrical equipment.

 DO NOT open the instrument under any circumstances.

3

CET Electric Technology

Limited warranty

CET Inc. (CET) offers the customer a minimum of 12-month functional warranty on the meter for faulty parts or workmanship from the date of dispatch from the

CET does not accept liability for any damage caused by meter malfunctions. CET accepts no responsibility for the suitability of the meter to the application for

Failure to install, set up or operate the meter according to the instructions herein

Only CET’s duly authorized representative may open your meter. The unit should only be opened in a fully anti-static environment. Failure to do so may damage



distributor. This warranty is on a return to factory for repair basis.



which it was purchased.



will void the warranty.



the electronic components and will void the warranty.

4

CET Electric Technology

Table of Contents

Chapter 1 Introduction ............................................................................................................................. 8

1.1 Overview .................................................................................................................................... 8

1.2 Features ...................................................................................................................................... 8

1.3 PMC-53A’ application in Power and Energy Management Systems ......................................... 11

1.4 Getting more information ........................................................................................................ 11

Chapter 2 Installation ............................................................................................................................. 12

2.1 Appearance .............................................................................................................................. 12

2.2 Unit Dimensions ....................................................................................................................... 13

2.3 Terminal Dimensions ................................................................................................................ 13

2.4 Mounting .................................................................................................................................. 13

2.5 Wiring connections .................................................................................................................. 14

2.5.1 3-Phase 4-Wire (3P4W) Wye Direct Connection with 3CTs .......................................... 15

2.5.2 3-Phase 4-Wire (3P4W) Wye Direct Connection with 4CTs .......................................... 15

2.5.3 3-Phase 4-Wire (3P4W) Wye with 3PTs and 3CTs ......................................................... 15

2.5.4 3-Phase 4-Wire (3P4W) Wye with 3PTs and 4CTs ......................................................... 16

2.5.5 3-Phase 3-Wire (3P3W) Direct Delta Connection with 3CTs ......................................... 16

2.5.6 3-Phase 3-Wire (3P3W) Direct Delta Connection with 2CTs ......................................... 17

2.5.7 3-Phase 3-Wire (3P3W) Delta with 2PTs and 3CTs ........................................................ 17

2.5.8 3-Phase 3-Wire (3P3W) Delta with 2PTs and 2CTs ........................................................ 18

2.5.9 1-Phase 3-Wire (1P3W) Direct Connection with 2CTs .................................................. 18

2.5.10 1-Phase 2-Wire, Uln (1P2W-Uln) Direct Connection with 1CT ................................... 19

2.5.11 1-Phase 2-Wire, Ull (1P2W-Ull) Direct Connection with 1CT ...................................... 19

2.6 Communications Wiring ........................................................................................................... 20

2.7 Digital or Pulse Input Wiring .................................................................................................... 20

2.8 Digital (Relay) Output Wiring ................................................................................................... 20

2.9 Pulse Output Wiring ................................................................................................................. 21

2.10 Analog Input Wiring ............................................................................................................... 21

2.11 Analog Output Wiring ............................................................................................................ 21

2.12 RTD Input Wiring .................................................................................................................... 22

2.13 Power Supply Wiring .............................................................................................................. 22

Chapter 3 Front Panel ............................................................................................................................. 23

3.1 Using the Front Panel Buttons .................................................................................................. 23

3.2 Data Display .............................................................................................................................. 24

3.2.1 U/I ................................................................................................................................. 24

3.2.2 Power ............................................................................................................................ 25

3.2.3 Energy ........................................................................................................................... 25

3.2.4 Demand ......................................................................................................................... 25

3.2.5 Harmonics ..................................................................................................................... 25

3.2.6 Max./Min. ..................................................................................................................... 26

3.2.7 TOU ............................................................................................................................... 27

3.2.8 I/O ................................................................................................................................. 28

3.2.9 SOE ................................................................................................................................ 28

5

CET Electric Technology

3.3 Setup Configuration via the Front Panel .................................................................................. 28

3.3.1 Making Setup Changes .................................................................................................. 28

3.3.2 Setup Menu .................................................................................................................. 30

3.3.3 Configuration ................................................................................................................ 31

Chapter 4 Applications ........................................................................................................................... 36

4.1 Inputs and Outputs .................................................................................................................. 36

4.1.1 Digital Inputs ................................................................................................................. 36

4.1.2 Digital Outputs .............................................................................................................. 36

4.1.3 Energy Pulse Outputs .................................................................................................... 37

4.1.4 Analog Input .................................................................................................................. 37

4.1.5 Analog Output ............................................................................................................... 37

4.1.6 RTD Input ...................................................................................................................... 38

4.2 Power and Energy .................................................................................................................... 38

4.2.1 Basic Measurements ..................................................................................................... 38

4.2.2 Energy Measurements .................................................................................................. 39

4.2.3 Interval Energy Measurements ..................................................................................... 39

4.2.4 Demand Measurements ............................................................................................... 39

4.3 Power Quality ........................................................................................................................... 40

4.3.1 Phase Angles ................................................................................................................. 40

4.3.2 Power Quality Parameters ............................................................................................ 40

4.3.3 Unbalance ..................................................................................................................... 41

4.4 Setpoints .................................................................................................................................. 42

4.5 Logging ..................................................................................................................................... 44

4.5.1 Max./Min. Log ............................................................................................................... 44

4.5.2 Peak Demand Log ......................................................................................................... 44

4.5.3 Monthly Energy Log ...................................................................................................... 45

4.5.4 Daily and Monthly Freeze Log (Optional) ...................................................................... 45

4.5.5 SOE Log ......................................................................................................................... 46

4.5.6 Data Recorder (DR) Log (Optional) ................................................................................ 46

4.6 Time of Use (TOU) .................................................................................................................... 47

4.7 Diagnostics ............................................................................................................................... 48

Chapter 5 Modbus Register Map ............................................................................................................ 49

5.1 Basic Measurements ................................................................................................................ 49

5.2 Energy Measurements ............................................................................................................. 51

5.2.1 3-Phase Total Energy Measurements ............................................................................ 51

5.2.2 Phase A (L1) Energy Measurements ............................................................................. 52

5.2.3 Phase B (L2) Energy Measurements .............................................................................. 53

5.2.4 Phase C (L3) Energy Measurements .............................................................................. 54

5.2.5 Interval Energy Measurements ..................................................................................... 55

5.3 DI Pulse Counters ..................................................................................................................... 55

5.4 Harmonic Measurements ......................................................................................................... 55

5.4.1 Power Quality Measurements ...................................................................................... 55

5.4.2 Current Harmonic Measurements ................................................................................ 56

5.4.3 Voltage Harmonic Measurements ................................................................................ 56

6

CET Electric Technology

5.5 Demands .................................................................................................................................. 56

5.5.1 Present Demands .......................................................................................................... 57

5.5.2 Predicted Demands ....................................................................................................... 57

5.5.3 Peak Demand Log of This Month (Since Last Reset) ..................................................... 57

5.5.4 Peak Demand Log of Last Month (Before Last Reset) ................................................... 57

5.5.5 Demand Data Structure ................................................................................................ 58

5.6 Max./Min. Log .......................................................................................................................... 58

5.6.1 Max. Log of This Month (Since Last Reset) ................................................................... 58

5.6.2 Min. Log of This Month (Since Last Reset) .................................................................... 59

5.6.3 Max. Log of Last Month (Before Last Reset) ................................................................. 60

5.6.4 Min. Log of Last Month (Before Last Reset) .................................................................. 61

5.6.5 Max./Min. Log Structure ............................................................................................... 61

5.7 Monthly Energy Log ................................................................................................................. 62

5.8 Daily and Monthly Freeze Logs (Optional) ............................................................................... 63

5.8.1 Daily Freeze Log ............................................................................................................ 63

5.8.2 Monthly Freeze Log ....................................................................................................... 63

5.9 SOE Log ..................................................................................................................................... 64

5.10 Data Recorder Log (Optional) ................................................................................................. 68

5.11 Device Setup ........................................................................................................................... 68

5.11.1 Basic Setup Parameters ............................................................................................... 68

5.11.2 I/O Setup ..................................................................................................................... 70

5.11.3 Communication Setup Parameters ............................................................................. 72

5.11.4 Setpoints Setup ........................................................................................................... 72

5.11.5 Data Recorder Setup ................................................................................................... 73

5.12 TOU Setup .............................................................................................................................. 74

5.12.1 Basic ............................................................................................................................ 74

5.12.2 Season ......................................................................................................................... 75

5.12.3 Daily Profile ................................................................................................................. 76

5.12.4 Alternate Days ............................................................................................................. 77

5.13 Time ........................................................................................................................................ 78

5.14 Remote Control ...................................................................................................................... 78

5.15 Clear/Reset Control ................................................................................................................ 79

5.16 Meter Information.................................................................................................................. 80

Appendix A Data Recorder Parameter List ............................................................................................. 82

Appendix B Data Recorder Default Settings ........................................................................................... 83

Appendix C BACNet MSTP Implementation ........................................................................................... 84

Appendix D N2 Implementation ............................................................................................................. 89

Appendix E DNP Profile .......................................................................................................................... 91

Appendix F Technical Specifications ....................................................................................................... 99

Appendix G Standards Compliance ...................................................................................................... 101

Appendix H Ordering Guide ................................................................................................................. 102

Contact us ............................................................................................................................................. 103

7

CET Electric Technology

Chapter 1 Introduction

This manual explains how to use the PMC-53A Intelligent Multifunction Meter. Throughout the manual the term “meter” generally refers to all models.

This chapter provides an overview of the PMC-53A meter and summarizes many of its key features.

1.1 Overview

The PMC-53A Intelligent Multifunction Meter is CET’s latest offer for the low-cost digital power/energy metering market. The PMC-53A features quality construction, multifunction measurements and a large, backlit, Dot-Matrix LCD that is easy to navigate. Housed in a standard DIN form factor measuring 96x96x88mm, it is perfectly suited for industrial, commercial and utility applications. Compliance with the IEC 62053-22 Class 0.5S Standard, it is a cost effective replacement for analog instrumentation and is capable of displaying 4 measurements at once. It optionally provides I4 input for Neutral Current measurement, a second RS485 port, up to six Digital Inputs for status monitoring, pulse counting or Tariff switching, up to four Relay Outputs for control and alarming applications, up to four Solid State Relays for energy pulsing as well as other I/O options for different applications.

You can setup the meter through its front panel or via our free PMC Setup software. The meter is also supported by our PecStar® iEMS Integrated Energy Management System. Following is a list of typical applications for the PMC-53A:

 Industrial, Commercial and Utility Substation Metering  Building, Factory and Process Automation  Sub-metering and Cost Allocation  Energy Management and Power Quality Monitoring

Contact CET Technical Support at support@cet-global.com should you require further assistance with your application.

1.2 Features

Ease of use

 Large, backlit, Dot-Matrix LCD display with wide viewing angle  Intuitive user interface  LED indicators for Energy Pulsing and Communication activities  Password-protected setup via front panel or free PMC Setup software  Easy installation with mounting clips, no tools required

Basic Measurements (True RMS)

 ULN, ULL per phase and Average  Current per phase and Average with calculated Neutral  kW, kvar, kVA, PF per phase and Total  kWh, kvarh Import / Export / Net / Total and kVAh Total  Frequency  Device Operating Time (Running Hours)  Optional I4 measurements  Calculated Residual Current Ir (with optional I4 Input)

8

CET Electric Technology

Advanced Measurements

 1-Cycle Real-time U & I Waveform Display @ 1s update rate  U and I THD, TOHD, TEHD and Individual Harmonics up to 31st  Current TDD, TDD Odd, TDD Even, K-Factor and Crest Factor  U and I Unbalance and Phase Angles  Displacement PF  Fundamental U, I and kW per phase  Total Fundamental kW & Total Harmonic kW*  U and I Symmetrical (Sequence) Components*  kvarh Q1-Q4  Interval Energy for kWh/kvarh Imp/Exp and kVAh  Demands, Predicted Demands and Peak Demands for kW/kvar/kVA Total and per phase Current

with Timestamp for This Month (or Since Last Reset) and Last Month (or Before Last Reset)

 Two TOU schedules, each providing

o 12 Seasons o 20 Daily Profiles, each with 12 Periods in 15-minute interval o 90 Holidays or Alternate Days o 8 Tariffs, each providing the following information

· kWh/kvarh Import/Export, kVAh

· kW/kvar/kVA Max. Demands

 12 Monthly Energy Logs of kWh/kvarh Import/Export/Total/Net, kVAh, kvarh Q1-Q4 as well as

kWh/kvarh Import/Export and kVAh per Tariff

*Available in Firmware V1.00.03 or later

Setpoints

 9 user programmable Setpoints with extensive list of monitoring parameters including Voltage,

Current, Power and THD, etc.

 Configurable thresholds, time delays and DO triggers

SOE Log

 100 events time-stamped to ±1ms resolution  Recording events for Setup changes, Setpoint and DI status changes as well as DO operations

Max/Min Log

 Max./Min. Log with timestamp for parameters such as Voltage, Current, In (calculated), I4, Ir,

Frequency, kW, kvar, kVA, PF, Unbalance, K-Factor, Crest-Factor and THD

 Configurable for This Month/Last Month or Since/Before Last Reset

Freeze Logs (Optional)

 60 Daily Freeze Logs for kWh/kvarh/kVAh Total and kW/kvar/kVA Peak Demands.  36 Monthly Freeze Logs for kWh/kvarh/ kVAh Total and kW/kvar/kVA Peak Demands with

Timestamp.

Data Recorder Log (Optional)

 5 Data Recorders of 16 parameters each for real-time measurements, harmonics, energy, demand,

TOU, Pulse Counters…etc.

 Recording interval from 1 minute to 40 days  Configurable capacity up to a max. of 100 days at 15-minute interval

9

CET Electric Technology

Diagnostics

 Frequency Out-of-Range, Loss of Voltage / Current  kW Direction per phase and Total, Possible Incorrect CT Polarity  Incorrect U & I Phase Sequence

Communications

 Optically isolated RS485 port at max. 38,400 bps  Selectable Modbus RTU, BACnet MS/TP*, Metasys N2* and DNP 3.0~  Optional 2nd RS485 port with Modbus RTU support only

*Available in Firmware V1.00.03 or later ~Available in Firmware V1.00.06 or later

Optional Inputs and Outputs  Digital Inputs

o Up to 6 channels, volts free dry contact, 24VDC internally wetted o 1000Hz sampling for status monitoring with programmable debounce o Pulse counting with programmable weight for each channel for collecting WAGES (Water,

Air, Gas, Electricity, Steam) information

o Tariff switching based on DI status

 Digital Outputs

o Up to 4 Form A mechanical relays for alarming and general purpose control

 Pulse Outputs

o Up to 4 Form A Soild State Relays for kWh and kvarh pulsing with Max. Load Voltage @

50VDC and Max. Forward Current @ 50mA

Optional Expansion Modules  Expansion Module A Options

o I4 Input o 2nd RS485 port with optical isolation, supporting Modbus RTU

 Expansion Module B Options

o 2xDigital Inputs and 2xRelay Outputs o 2xDigital Inputs and 2xSold State Pulse Outputs o 2xRTD Inputs (PT100 sensor not included) o 1xAI and 1xAO (0/4-20mA)

System Integration

 Supported by CET’s PecStar® iEMS and iEEM  Modbus RTU for easy integration into 3rd-party Energy Management, Automation or SCADA

systems

 BACnet MSTP and Metasys N2 for Building Automation  DNP 3.0 for Utility Substation Automation

10

CET Electric Technology

1.3 PMC-53A’ application in Power and Energy Management Systems

The PMC-53A can be used to monitor 4P3W (Wye), 3P3W (Delta), 1P2W-Uln, 1P2W-Ull or 1P3W connected power system. Modbus communications allow real-time data, DI status and other information to be transmitted across a RS485 network to an Integrated Energy Management system such as PecStar® iEMS.

1.4 Getting more information

Additional information is available from CET via the following sources:

 Visit www.cet-global.com  Contact your local representative  Contact CET Technical Support directly via email at support@cet-global.com

11

CET Electric Technology

Installation of the PMC-53A should only be performed by qualified, competent personnel that have the appropriate training and experience with high voltage and current devices.

During the operation of the meter, hazardous voltages are present at the input terminals.

Failure to observe precautions can result in serious or even fatal injury and equipment damage.

Chapter 2 Installation

Caution

The meter must be installed in accordance with all local and national electrical codes.

2.1 Appearance

Figure 2-1 Appearance

12

2.2 Unit Dimensions

Terminal

Terminal Dimensions

Wire Size

Max. Torque

1

Voltage Input

2.6mm x 3.2mm

1.5mm2

5 kgf.cm/M3

(4.3 lb-in)

Power Supply

2

Expansion Module A & B

RS485

DI

DO

3

Current Input

6.5mm x 6.5mm

1.0mm2 - 2.5mm2

(14AWG - 22AWG)

6.0 kgf.cm/M3 (5.2 lb-in)

2.3 Terminal Dimensions

CET Electric Technology

Figure 2-2 Unit Dimensions

Figure 2-3 Terminal Dimensions

Table 2-1 Terminal Dimensions

2.4 Mounting

The PMC-53A should be installed in a dry environment with no dust and kept away from heat, radiation and electrical noise source.

Installation steps:

 Remove the installation clips from the meter  Fit the meter through a 92mmx92mm cutout as shown in Figure 2-4  Re-install the installation clips and push the clips tightly against the panel to secure the meter

13

CET Electric Technology

Under no circumstances should the CT secondary be open when the CT primary is energized. CT shorting blocks should be installed to allow for easy maintenance.

Figure 2-4 Panel Cutout Mounting

2.5 Wiring connections

PMC-53A can satisfy almost any three phase power systems. Please read this section carefully before installation and choose the correct wiring method for your power system. The following Wiring Modes are supported:

 3-Phase 4-Wire (3P4W) Wye Direct Connection with 3CTs  3-Phase 4-Wire (3P4W) Wye Direct Connection with 4CTs  3-Phase 4-Wire (3P4W) Wye with 3PTs and 3CTs  3-Phase 4-Wire (3P4W) Wye with 3PTs and 4CTs  3-Phase 3-Wire (3P3W) Direct Delta Connection With 3CTs  3-Phase 3-Wire (3P3W) Direct Delta Connection with 2CTs  3-Phase 3-Wire (3P3W) Delta with 2PTs and 3CTs  3-Phase 3-Wire (3P3W) Delta with 2PTs and 2CTs  1-Phase 3-Wire (1P3W) Direct Connection with 2CTs  1-Phase 2-Wire, Uln (1P2W-Uln) Direct Connection with 1CT  1-Phase 2-Wire, Ull (1P2W-Ull) Direct Connection with 1CT

Caution

Under no circumstances should the PT secondary be shorted.

14

CET Electric Technology

2.5.1 3-Phase 4-Wire (3P4W) Wye Direct Connection with 3CTs

Please consult the serial number label to ensure that the rated system phase voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 3P4W.

Figure 2-5 3P4W Direct Connection with 3CTs

2.5.2 3-Phase 4-Wire (3P4W) Wye Direct Connection with 4CTs

Please consult the serial number label to ensure that the rated system phase voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 3P4W

Figure 2-6 3P4W Direct Connection with 4CTs (Optional I41 & I42)

2.5.3 3-Phase 4-Wire (3P4W) Wye with 3PTs and 3CTs

Please consult the serial number label to ensure that the rated PT secondary voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 3P4W.

15

CET Electric Technology

Figure 2-7 3P4W with 3PTs and 3CTs

2.5.4 3-Phase 4-Wire (3P4W) Wye with 3PTs and 4CTs

Please consult the serial number label to ensure that the rated PT secondary voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 3P4W.

Figure 2-8 3P4W with 3PTs and 4CTs (Optional I41 & I42)

2.5.5 3-Phase 3-Wire (3P3W) Direct Delta Connection with 3CTs

Please consult the serial number label to ensure that the rated system line voltage is less than or equal

to the meter’s rated line voltage input specification. Set the Wiring Mode to 3P3W.

16

CET Electric Technology

Figure 2-9 3P3W Direct Connection with 3CTs

2.5.6 3-Phase 3-Wire (3P3W) Direct Delta Connection with 2CTs

Please consult the serial number label to ensure that the rated system line voltage is less than or equal

to the meter’s rated line voltage input specification. Set the Wiring Mode to 3P3W.

Figure 2-10 3P3W Direct Connection with 2CTs

2.5.7 3-Phase 3-Wire (3P3W) Delta with 2PTs and 3CTs

Please consult the serial number label to ensure that the rated PT secondary voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 3P3W.

17

CET Electric Technology

Figure 2-11 3P3W Delta with 2PTs and 3CTs

2.5.8 3-Phase 3-Wire (3P3W) Delta with 2PTs and 2CTs

Please consult the Serial Number Label to ensure that the rated PT secondary voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 3P3W.

Figure 2-12 3P3W Delta with 2PTs and 2CTs

2.5.9 1-Phase 3-Wire (1P3W) Direct Connection with 2CTs

Please consult the Serial Number Label to ensure that the rated system phase voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 1P3W.

18

CET Electric Technology

Figure 2-13 1P3W Direct Connection with 2CTs

2.5.10 1-Phase 2-Wire, Uln (1P2W-Uln) Direct Connection with 1CT

Please consult the Serial Number Label to ensure that the rated system phase voltage is less than or

equal to the meter’s rated phase voltage input specification. Set the Wiring Mode to 1P2W, L-N.

Figure 2-14 1P2W Uln Direct Connection with 1CT

2.5.11 1-Phase 2-Wire, Ull (1P2W-Ull) Direct Connection with 1CT

Please consult the Serial Number Label to ensure that the rated system line voltage is less than or equal

to the meter’s rated phase voltage input specification. Set the Wiring Mode to 1P2W, L-L.

19

CET Electric Technology

Figure 2-15 1P2W Ull Direct Connection with 1CT

2.6 Communications Wiring

The following figure illustrates the RS485 communications connections on the PMC-53A:

Figure 2-14 Communications Connections

The PMC-53A provides one standard RS485 port and one optional RS485. Up to 32 devices can be connected on a RS485 bus. The overall length of the RS485 cable connecting all devices should not exceed 1200m.

If the master station does not have a RS485 communications port, a RS232/RS485, USB/RS485 or Ethernet/RS485 converter with optically isolated output and surge protection should be used.

2.7 Digital or Pulse Input Wiring

The following figure illustrates the Digital Input connections on the PMC-53A:

Figure 2-16 DI Connections

2.8 Digital (Relay) Output Wiring

The following figures illustrate the Digital (Relay) Output connections on the PMC-53A:

20

CET Electric Technology

Figure 2-17 DO Connections

2.9 Pulse Output Wiring

The following figure illustrates the Pulse Output connections on the PMC-53A when the DO Control Mode setup register is programmed for Energy Pulsing:

Figure 2-18 Pulse Output (Solid State Relay) Connections for Energy Pulsing

The following figure illustrates the Pulse Output (Solid State Relay) connections on the PMC-53A when the DO Control Mode setup register is programmed for Remote Control/Alarm:

Figure 2-19 Pulse Output (Solid State Relay) Connections for Remote Control/Alarm

2.10 Analog Input Wiring The following figure illustrates the Analog Input connections on the PMC-53A:

Figure 2-20 AI Connections

2.11 Analog Output Wiring

The following figure illustrates the Analog Output connections on the PMC-53A:

21

CET Electric Technology

Figure 2-21 AO Connections

2.12 RTD Input Wiring

The following figure illustrates the RTD Input connections on the PMC-53A:

Figure 2-22 RTD Input Connections

2.13 Power Supply Wiring

For AC supply, connect the live wire to the L/+ terminal and the neutral wire to the N/- terminal.

For DC supply, connect the positive wire to the L/+ terminal and the negative wire to the N/- terminal.

Figure 2-23 Power Supply Connections

22

CET Electric Technology

Display Mode

Setup Mode

Button

Main Menu

Sub Menus

Password

Page

Enter

Password

Browse/Setup Menu (Until a parameter is

selected)

Enumerated

Parameter

Numeric

Parameter

F1

←

(Menu Left)

Esc

(Exit)

Esc

(Exit)

Cancel

(Exit)

Esc

(Exit)

Cancel

(Exit)

Cancel

(Exit)

F2

Select Option

↑ (Page Up) or

Select Option

Browse

(View Only)

←

(Shift Left)

↑

(Cursor Up)

←

(Previous)

←

(Shift Left)

F3

Select Option

↓ (Page Down) or

Select Option

Null

(Not Used)

↑

(Increment)

↓

(Cursor Down)

↑

(Next)

↑

(Increment)

F4

→

(Menu Right)

→ (Menu Right) or

Select Option or

Null (Not Used)

Enter

(Confirm)

OK

(Confirm)

Enter

(Select Parameter)

OK

(Confirm)

OK

(Confirm)

Chapter 3 Front Panel

The PMC-53A has a large, easy to read Dot-Matrix LCD display with backlight and four buttons for data display and meter configuration. This chapter introduces the front panel operations.

Figure 3-1 Front Panel

3.1 Using the Front Panel Buttons

The PMC-53A’s front panel has been designed with a menu-driven interface that is extremely user friendly such that all one has to do is to simply follow the menu at the bottom of the screen. The button definitions for F1 to F4 under Display Mode and Setup Mode are explained in the following table. The

default password is 0000 (four zeros).

Table 3-1 Button Function

23

3.2 Data Display

Press Button

Display Screens

1st Row

2nd Row

3rd Row

4th Row

<U/I>

Default

Ull avg

I avg

kW Total

PF Total

Display 1 (Volts L-N)

U1

U2

U3

Uln avg

Display 2 (Volts L-L)

U12

U23

U31

Ull avg

Display 3 (Currents)

I1

I2

I3

I avg

Display 4 (In/I4/Ir)

In

I41

Ir#2 Display 5 (Frequency)

Frequency

Display 6 (Volts Angle)

U1

U2

U3

Display 7 (Currents Angle)

I1

I2

I3

Display 8 (Phasor Diagram)

Phasor Diagram

Display 9 (U Waveform)#

U1 Real-time 1-cycle Waveform

Display 10 (U Waveform)#

U2 Real-time 1-cycle Waveform

Display 11 (U Waveform)#

U3 Real-time 1-cycle Waveform

Display 12 (I Waveform)#

I1 Real-time 1-cycle Waveform

Display 13 (I Waveform)#

I2 Real-time 1-cycle Waveform

Display 14 (I Waveform)#

I3 Real-time 1-cycle Waveform

Display 15 (Operating Time)

Operating Time (Running Hours)

Display 16 (U Fund)*

U13

U23

U33 Display 17 (I Fund)*

I13

I23

I33

CET Electric Technology

Figure 3-2 Data Display Menu

Throughout this document, the phase-to-neutral notations of A/B/C and L1/L2/L3 as well as the phaseto-phase notations of AB/BC/CA and L12/L23/L31 may be used interchangeably for specifying a certain parameter to be a phase-to-neutral or phase-to-phase value, respectively.

The following sections illustrate the available measurements for each display option. Depending on the Wiring Mode selected, certain measurements may not be available. For example, the per-phase Uln, Uln Average, I4, per-phase kW, kvar, kVA and PF measurements are not available when the Wiring Mode is set to 3P3W or 1P2W L-L.

3.2.1 U/I

* Available in Firmware V1.00.03 or later

#

Available in Firmware V1.00.06 or later

Table 3-2 U/I Display

24

CET Electric Technology

Press Button

Display

Screens

1st Row

2nd Row

3rd Row

4th Row

<Power>

Display 1

kW Total

kvar Total

kVA Total

PF Total

Display 2

kW1

kW2

kW3

kW Total

Display 3

kvar1

kvar2

kvar3

kvar Total

Display 4

kVA1

kVA2

kVA3

kVA Total

Display 5

PF1

PF2

PF3

PF Total

Display 6

dPF1

dPF2

dPF3

Display 7

(P Fund)*

P1

P2

P3

P

Press Button

Display

Screens

1st Row

2nd Row

3rd Row

4th Row

Display 1

kWh Total

kvarh Total

kVAh Total

Display 2

kWh Imp

kWh Exp

kWh Net

kWh Total

Display 3

kvarh Imp

kvarh Exp

kvarh Net

kvarh Total

Display 4

kVAh Total

Press Button

Display

Screens

1st Row

2nd Row

3rd Row

<DMD>

1

<Max>

2

Display 1

kW Total

kvar Total

kVA Total

Timestamp

Display 2

I1

I2

I3

Timestamp

<Pres>

3

Display 1

kW Total

kvar Total

kVA Total

Display 2

I1

I2

I3

<Pred>

4

Display 1

kW Total

kvar Total

kVA Total

Display 2

I1

I2

I3

Press Button

Display Screens

1st Row

2nd Row

3rd Row

<Basic>

Display 11 (U THD)

U1/U12

U2/U23

U3/U31

Display 2 (I THD)

I1

I2

I3

Display 3 (TDD)

I1

I2

I3

Display 4 (K-Factor)

I1

I2

I3

Display 5 (Crest Factor)

I1

I2

I3

Notes:

1) The I4 parameter only appears if the meter is equipped with the corresponding I4 option.

2) The Ir parameter only shows a valid value when the Wiring Mode is set to 3P3W or 3P4W;

otherwise, it shows “0”.

3) For U/I Fundamental:

 U1 = Uan, U2 = Ubn, U3 = Ucn in 3P4W mode  U1 = Uab, U2 = Ubc, U3 = Uca in 3P3W mode  I1 = Ia, I2 = Ib, I3 = Ic

3.2.2 Power

* Available in Firmware V1.00.03 or later

Table 3-3 Power Display

3.2.3 Energy

Table 3-4 Energy Display

3.2.4 Demand

Table 3-5 Demand Display

Notes:

1) DMD = Demand

2) Max = Max. (Peak) Demand of This Month (Since Last Reset)

3) Pres = Present Demand

4) Pred = Predicted Demand

3.2.5 Harmonics

25

CET Electric Technology

Display 6 (Unbalance)

Current

Voltage

Display 7

(U Sequence)*

U1

2,3

U2

2,3

U0

2,3

Display 8

(I Sequence)*

I1

2,3

I2

2,3

I0

2,3

<Graph>

Display 11

U1/U12 Harmonic Spectrum (Odd)

Display 21

U2/U23 Harmonic Spectrum (Odd)

Display 31

U3/U31 Harmonic Spectrum (Odd)

Display 4

I1 Harmonic Spectrum (Odd)

Display 5

I2 Harmonic Spectrum (Odd)

Display 6

I3 Harmonic Spectrum (Odd)

<L1>

Display 1 [HD (ODD)]

HD3 ~ HD15

Display 2 [HD (ODD)]

HD17 ~ HD29

Display 3 [HD (ODD)]

HD31

Display 1 [HD (Even)]

HD2 ~ HD14

Display 2 [HD (Even)]

HD16 ~ HD28

Display 3 [HD (Even)]

HD30

<L2>

Display 1 [HD (ODD)]

HD3 ~ HD15

Display 2 [HD (ODD)]

HD17 ~ HD29

Display 3 [HD (ODD)]

HD31

Display 1 [HD (Even)]

HD2 ~ HD14

Display 2 [HD (Even)]

HD16 ~ HD28

Display 3 [HD (Even)]

HD30

<L3>

Display 1 [HD (ODD)]

HD3 ~ HD15

Display 2 [HD (ODD)]

HD17 ~ HD29

Display 3 [HD (ODD)]

HD31

Display 1 [HD (Even)]

HD2 ~ HD14

Display 2 [HD (Even)]

HD16 ~ HD28

Display 3 [HD (Even)]

HD30

Press Button

Display

Screens

1st Row

2nd Row

3rd Row

4th Row

<Max./Min.>

-

Default

(Max.)

U1

U2

U3

Uln avg

Timestamp

<Max.>

<U/I>

Display 1

U1

U2

U3

Uln avg

Timestamp

Display 2

U12

U23

U31

Ull avg

Timestamp

Display 3

I1

I2

I3

I avg

Timestamp

Display 4

Freq

In

I4

Ir*

Timestamp

<Power>

Display 1

P1

P2

P3

P

Timestamp

Display 2

Q1

Q2

Q3

Q

Timestamp

* Available in Firmware V1.00.03 or later

Table 3-6 Harmonics Display

Notes:

1) When the Wiring Mode is 3P3W or 1P2W L-L, the phase A/B/C Voltage THD/TOHD/TEHD/HDxx

mean phase AB/BC/CA Voltage THD/TOHD/TEHD/HDxx.

2) For U/I Symmetrical Components:

 U1/I1 = Positive Sequence Voltage/Current  U2/I2 = Negative Sequence Voltage/Current  U0/I0 = Zero Sequence Voltage/Current

3) This screen is not shown if the Wiring Mode is set to 1P2W LN, 1P2W LL or 1P3W.

3.2.6 Max./Min.

26

CET Electric Technology

Display 3

S1

S2

S3

S

Timestamp

Display 4

PF1

PF2

PF3

PF

Timestamp

<Harm>

Display 1

L1 U THD

L2 U THD

L3 U THD

Timestamp

Display 2

L1 I THD

L2 I THD

L3 I THD

Timestamp

Display 3

L1 K-Factor

L2 K-Factor

L3 K-Factor

Timestamp

Display 4 L1 C-Factor

L2 C-Factor

L3 C-Factor

Timestamp

Display 6

I Unbal.

U Unbal.

Timestamp

<Min.>

<U/I>

Display 1

U1

U2

U3

Uln avg

Timestamp

Display 2

U12

U23

U31

Ull avg

Timestamp

Display 3

I1

I2

I3

I avg

Timestamp

Display 4

Freq

In

I4

Ir*

Timestamp

<Power>

Display 1

P1

P2

P3

P

Timestamp

Display 2

Q1

Q2

Q3

Q

Timestamp

Display 3

S1

S2

S3

S

Timestamp

Display 4

PF1

PF2

PF3

PF

Timestamp

<Harm>

Display 1

L1 U THD

L2 U THD

L3 U THD

Timestamp

Display 2

L1 I THD

L2 I THD

L3 I THD

Timestamp

Display 3

L1 K-Factor

L2 K-Factor

L3 K-Factor

Timestamp

Display 4 L1 C-Factor

L2 C-Factor

L3 C-Factor

Timestamp

Display 6

I Unbal.

U Unbal.

Timestamp

Press button

Display screens

1st Row

2nd Row

3rd Row

<TOU>

<T1>

Display 1 (kWh)

Import

Export

Display 2 (kvarh)

Import

Export

Display 3 (kVAh)

Total

Display 4

(Peak Demand)

P Q S

Timestamp

<T2>

. . .

<T7>

Display 1 (kWh)

Import

Export

Display 2 (kvarh)

Import

Export

Display 3 (kVAh)

Total

Display 4

(Peak Demand)

P Q S

Timestamp

<T8>

Display 1 (kWh)

Import

Export

Display 2 (kvarh)

Import

Export

Display 3 (kVAh)

Total

Display 4

P Q S

*Available in Firmware V1.00.06 or later

Table 3-7 Max./Min. Display

3.2.7 TOU

27

CET Electric Technology

(Peak Demand)

Timestamp

Press button

Display screens

1st Row

2nd Row

3rd Row

<I/O>

Display 1 (DI Status)

DI1, DI21

DI3, DI41

DI5, DI6

1

Display 2 (Pulse Counter)

DI1, DI21

DI3, DI41

DI5, DI6

1

Display 3 (DO Status)

DO1, DO22

DO3, DO42

Display 4 (Analog Input)

AI3

Display 5 (Analog Output)

AO4

Display 6 (Temperature)

TC15

TC25

Table 3-8 TOU Display

3.2.8 I/O

Table 3-9 I/O

Notes:

1) This display only appears if the meter is equipped with the corresponding DI option.

2) This display only appears if the meter is equipped with the corresponding DO option.

3) This display only appears if the meter is equipped with the AI option.

4) This display only appears if the meter is equipped with the AO option.

5) This display only appears if the meter is equipped with the RTD option.

3.2.9 SOE

The PMC-53A with Firmware V1.00.03 or later supports the display of the SOE Log with up to 100 Events (2 Events per page) such as I/O Changes, Setpoint, …etc, on the Front Panel. In addition, the SOE Log can be reset from the Front Panel.

Examples of Event Log Display:

Figure 3-3 SOE Log Displays

3.3 Setup Configuration via the Front Panel

Pressing <←>/<F1> or <→>/<F2> to scroll the menu at the bottom until <Setup> appears and then press the button associated with <Setup> to browse or change the setup parameters.

3.3.1 Making Setup Changes

1) Entering the Password:

 Press <Setup> to enter the Setup Mode.  Press <F4>/<Enter> to advance to the Password page.  A correct password must be entered before changes are allowed. The factory default password is

 Press <F2>/<←> to shift the cursor to the left or <F3>/<↑> to increment the numeric value for the

“0000”.

password.

28

CET Electric Technology

 When the password has been entered, pressing <F4>/<OK> will advance to the setup menu if the

password is correct.

2) Selecting a parameter to change:

 Press <F2>/<↑> or <F3>/<↓> to scroll to the desired sub-menu or parameter.  Press <F4>/<Enter> to select the sub-menu or parameter.  Repeat the step 2 until a setup parameter has been selected.

3) Changing and saving a setup parameter:

 For a Numeric parameter, press <F2>/<←> to shift the cursor to the left or <F3>/<↑> to increment

the numeric value

 For an Enumerated parameter, press <F2>/<←> or <F3>/<↑> to scroll backward and forward in the

selection list.

 After modification, press <F4>/<OK> to save the change into memory or <Cancel> to exit the

currently selected parameter without change.

 Repeat step 3) until all setup parameters have been changed.

4) Exiting the Setup Mode

 Press <F1>/<Esc> to return to the Display Mode.  Also, the Setup Mode will be automatically exited if there is a period of inactivity of 1 minute or

longer.

29

3.3.2 Setup Menu

CET Electric Technology

Figure 3-3 Setup Menu

30

CET Electric Technology

Label

Description

Range

Default

Menu

1st

2nd

3rd

Password

Enter Password

0000 to 9999

0000

Basic

Wiring Mode

Meter’s Wiring Connection

DEMO/

1P2W L-N/1P2W L-L/

1P3W/3P3W/3P4W

3P4W

PT Primary

PT Primary Ratio

1 to 1000000V

100V

PT Secondary

PT Secondary Ratio

1 to 690V

100V

CT Primary

CT Primary Ratio

1 to 30000A

5A

CT Secondary

CT Secondary Ratio

1 to 5A

5A

I4 Primary~

I4 Primary Ratio

1 to 30000A

5A

I4 Secondary~

I4 Secondary Ratio

1 to 5A

5A

PF Convention

IEC/IEEE/-IEEE

IEC

kVA Calc.

kVA Calculation Method

Vector/Scalar

Vector

I1 Polarity

Normal/Reversed

Normal

I2 Polarity

I3 Polarity

THD Calc.

Select between

% of Fundamental or

% of RMS

THDf/THDr

THDf

DMD Period

Demand Interval

1 to 60 min

15

No. of Windows

Number of Sliding Windows

1 to 15

1

Predicted Resp.

Predicted Response

70 to 99

70

EN Pulse CNST

Pulse Constant

1000/3200

1000

LED EN Pulse

Enable kWh/kvarh Energy

Pulsing

Disabled/kWh/kvarh

kWh

EN Period*

Interval Energy period

5 to 60 min

60

kvarh Calc.~

kvarh Calculation Method

RMS/FUND

RMS

OT Threshold~

Current Threshold of

Device Operating Time

1 to 1000 (x0.001In)

1

Comm.

COM1

Protocol

Modbus/BACnet*/N2*/DNP~

Modbus

Unit ID

Modbus Address

Modbus RTU/N2*: 1 to 247

BACnet/MSTP*: 1 to 127

DNP~: 0 to 65519

100

Baud Rate

Data rate in bits per second

1200/2400/4800/

9600/19200/38400

9600

Data Format

8N2/8O1/8E1/

8N1/8O2/8E2

8E1

COM2

Protocol

Modbus

Unit ID

Modbus Address

1 to 247

101

Baud Rate

Data rate in bits per second

1200/2400/4800/

960019200/38400

9600

Data Format

8N2/8O1/8E1/

8N1/8O2/8E2

8E1

Setpoint*

Group #1

Type

Setpoint Type

0=Disabled, 1=Over Setpoint

2=Under Setpoint

0

Parameter

1

Setpoint Source

See Table 3-11

None

OvLim

Over Limit

0

UnLim

Under Limit

0

ActiveDelay

Active Delay

0 to 9999s

10

InactiveDelay

Inactive Delay

0 to 9999s

10

Trigger1

2

Setpoint Trigger1

See Table 3-12

Trigger22

Setpoint Trigger2

See Table 3-12

…

3.3.3 Configuration

The Setup Configuration mode provides access to the following setup parameters:

31

CET Electric Technology

Group #9

Type

Setpoint Type

0=Disabled, 1=Over Setpoint

2=Under Setpoint

0

Parameter1

Setpoint Source

See Table 3-11

None

OvLim

Over Limit

0 UnLim

Under Limit

0 ActiveDelay

Active Delay

0 to 9999s

0

InactiveDelay

Inactive Delay

0 to 9999s

10

Trigger12

Setpoint Trigger1

See Table 3-12

10

Trigger22

Setpoint Trigger2

See Table 3-12

I/O

Digital Input3

Function3

DI Function

DI1

Function Mode for DI1 to DI6

Digital Input /

Pulse Counter /

Tariff Switch

4

Digital

Input

…

DI6

Debounce3

Specifies the minimum duration the DI must remain in the Active or Inactive state before a state change is considered to be valid.

DI1

Debounce for DI1 to DI6

1 to 9999 ms

20 ms

…

DI6

Pulse Weight3

Specifies the incremental value for each pulse received

DI1

Pulse Weight for DI1 to DI6

1 to 1000000

1

…

DI6

Digital Output3

Pulse Width3

Specifies the duration for which the relay output will be active when a remote control command is received to activate it.

DO1

Pulse Width for DO1 to DO4

0 to 600 (x0.1s)

(0=Latch Mode)

10

DO2

DO3

DO4

Function3

Specifies the function of the Digital Output.

DO1#

DO Control Mode

 Remote Control / Alarm  kWh Import  kWh Export  kWh Total  kvarh Import  kvarh Export  kvarh Total

Remote

Control/

Alarm

DO2#

DO3

DO4

RTD

3

RTD1 Compensation

RTD Compensation5

0 to 2000 (x0.01Ω)

0.00Ω RTD2 Compensation

Analog Input3

Type

Select between

0-20mA or 4-20mA input

4-20mA / 0-20 mA

4-20mA

Zero Scale

The value that corresponds to

the minimum Analog Input of

0 or 4 mA

-999,999 to 999,999

400

Full Scale

The value that corresponds to the maximum Analog Input of

20 mA

-999,999 to 999,999

2000

Analog Output3

Type

Select between

0-20mA or 4-20mA output

4-20mA / 0-20mA

4-20mA

Key6

The parameter to which the

Analog Output is proportional

See Table 3-13

Uab

Zero Scale

The parameter value that

corresponds to the minimum

Analog Output of 0 mA or 4

mA

-999,999 to 999,999

0

Full scale

The parameter value that

corresponds to the maximum

Analog Output of 20 mA

-999,999 to 999,999

0

Display

Timeout

Backlight Timeout

0 to 60 min

5

Contrast

Display Contrast

0 to 9

5

32

CET Electric Technology

Language

System Language

Chinese/English

English

Delimiter7

Delimiter

Option1/Option2

Option1

Main 1st*

Default Display 1st parameter

See Note 8)

Ullavg

Main 2nd*

Default Display 2nd parameter

Iavg

Main 3rd*

Default Display 3rd parameter

P (kW Total)

Main 4th*

Default Display 4th parameter

PF (Total)

SP LCD Alarm~

9

Enable Flashing LCD Alarm

On/Off

On

Clock

Time

(20)YY-MM-DD

/

Date

HH:MM:SS

/

Date Format

YYMMDD/

MMDDYY/

DDMMYY

YYMMDD

Maintenance

Password Setup

New Password

Enter new password

Confirm Password

Confirm new password

Clear Registers

Energy

Present10

Clear Present Energy

Measurements and Energy Log

Yes/No

No

History11

Clear Historical Monthly

Energy Log

Yes/No

No

Demand

Present Max

Clear Peak Demand Log of This

Month (Since Last Reset)

Yes/No

No

All

Clear Present Demand, Peak

Demand Log of This Month

(Since Last Reset) and Last Month (Before Last Reset)

Yes/No

No

Max./Min.

Present

Clear Max./Min. Log of This

Month (Since Last Reset)

Yes/No

No

All

Clear Max./Min. Log of This

Month (Since Last Reset) and

Last Month (Before Last Reset)

Yes/No

No

Operating Time

Reset

Clear Device Operating Time

Yes/No

No

Pulse Counter

All

Clear All DI Counters

Yes/No

No

DI1

Clear

DIx Pulse Counter

Yes/No

No

…

DI6

SOE Logs*

Clear SOE Logs

Yes/No

No

Clear All Data

-

Clear All of the above

Yes/No

No

DO Control

DO1

DOx Manual Control

Normal/On/Off

Normal

DO2

DO3

DO4

Information

Check meter information

Firmware

Firmware Version

e.g. V1.00.01

Update

Date of the latest firmware

update

e.g.20160701

Modbus

Modbus Protocol Version

e.g. V1.4

BACnet MSTP*

BACnet MSTP Protocol Version

e.g. V1.7

N2*

N2 Protocol Version

e.g. V1.0

DNP~

DNP Protocol Version

e.g. V1.0

SN

Serial Number

e.g. 1506005094

* Available in Firmware V1.00.03 or later

#

Available in Firmware V1.00.04 or later

~ Available in Firmware V1.00.06 or later

Notes:

1) The table below illustrates the Setpoint Parameters.

Table 3-10 Setup Parameters

33

CET Electric Technology

Key

Setpoint Parameter

Scale

Unit

0

None

-

1

Uln (Any Phase Voltage)

x1

V

2

Ull (Any Line Voltage)

3

I (Any Phase Current)

A

4

In (Calculated)

5

Frequency

Hz

6

P (kW Total)

W

7

Q (kvar Total)

var

8

S (kVA Total)

VA

9

PF (PF Total)

-

10

P DMD (kW Total Present Demand)

W

11

Q DMD (kvar Total Present Demand)

var

12

S DMD (kVA Total Present Demand)

VA

13

P DMD Pred (kW Total Predicted Demand)

W

14

Q DMD Pred (kvar Total Predicted Demand)

var

15

S DMD Pred (kVA Total Predicted Demand)

VA

16

U THD

100%

17

U TOHD

100%

18

U TEHD

100%

19

I THD

100%

20

I TOHD

100%

21

I TEHD

100%

22

U Unbal (Voltage Unbalance)

100%

23

I Unbal (Current Unbalance)

100%

24

Reversal (Phase Reversal)3

-

25

I4 (Measured)*

x1

A

26

AI*

-

27

Reserved

-

28

RTD1*

x1

°C

29

RTD2*

30

Ir (Residual Current)~

x1

A

31

U2 (-ve Sequence Unbalance)~

x1

V

32

U0 (Zero Sequence Unbalance)~

Key

Action

Key

Action

0

None

3

DO3 Closed

1

DO1 Closed

4

DO4 Closed

2

DO2 Closed

Others

Reserved

Key

Parameter

Scale

Unit

Key

Parameter

Scale

Unit 0 Uab

x1

V

10

kVA Total

x1

kVA 1 Ubc

V

11

PF Total

x1000

- 2 Uca

V

12

Frequency

x100

-

3

Ull Average

V

13

kW Total Present Demand

x1

kW

4

Ia

A

14

kvar Total Present Demand

kvar

5

Ib

A

15

kVA Total Present Demand

kVA

6

Ic

A

16

Uan

x1

V 7 I Average

A

17

Ubn

V

8

kW Total

x1

kW

18

Ucn

V

9

kvar Total

kvar

19

Uln Average

V

* Appears only if the device is equipped with the appropriate option ~ Available in Firmware V1.00.06 or later

Table 3-11 Setpoint Parameters

2) The table below illustrates the options for Setpoint Trigger.

Table 3-12 Setpoint Trigger

3) This menu only appears if the meter is equipped with the corresponding options.

4) Tariff Switching is available in Firmware V1.00.03 or later and only valid for DI1 to DI3.

5) Please refer to Chapter 4.1.6 for a detailed description of RTD Compensation.

6) Analog Output Parameters

If PF Total or Freq is chosen as the AO parameter, the values for ZERO (zero scale) and FULL (full scale) should be set as 1000 or 100 times the actual value, respectively. The Units for Voltage, Current, kW, kvar, kVA and FREQ are V, A, kW, kvar, kVA and Hz, respectively.

Table 3-13 Analog Output Parameters

34

CET Electric Technology

Key

Parameters

Key

Parameters

Key

Parameters

Key

Parameters

0

U1 (Uan)

10

I3 (Ic)

20

T1 kWh Imp

30

Fund. kW Total*

1

U2 (Ubn)

11

Iavg

21

T2 kWh Imp

31

dPF Total*

2

U3 (Ucn)

12

P (kW Total)

22

T3 kWh Imp

32

I4*

3

Ulnavg

13

Q (kvar Total)

23

T4 kWh Imp

33

U1 THD*

4

U12 (Uab)

14

S (kVA Total)

24

I1 (Ia) Demand

34

U2 THD*

5

U23 (Ubc)

15

PF (PF Total)

25

I2 (Ib) Demand

35

U3 THD*

6

U31 (Uca)

16

Frequency

26

I3 (Ic) Demand

36

Ir*

7

Ullavg

17

kWh Import

27

kW Demand

8

I1 (Ia)

18

kWh Export

28

kvar Demand*

9

I2 (Ib)

19

kWh Total

29

kVA Demand*

7) The Delimiter setup register supports two options, 1 and 2:

Option 1: “,” is used as the x1000 delimiter and “.” as the decimal point (e.g. 123,456,789.0). Option 2: “ ” is used as the x1000 delimiter and “,” as the decimal point (e.g. 123 456 789,0).

8) The following table illustrates the parameters that can be selected for display in the Default Display

screen.

* Available in Firmware V1.00.06 or later

Table 3-14 Default Display Parameters

9) Setting SP LCD Alarm to On would make the LCD blink when there is an active Setpoint alarm, and

pressing any button would jump to the first SOE log screen.

10) Select Present to clear 3-Phase Total Energy registers, Phase A/B/C Energy registers, Tariff Energy

and Monthly Energy Log of the Present Month.

11) Select History to clear the Monthly Energy Log of the last 1 to 12 months, excluding the Monthly

Energy Log for the Present Month.

35

CET Electric Technology

Setup Parameter

Definition

Options

DIx Function

Each DI can be configured as a Digital Input or Pulse Counter. Only DI1 to DI3 can be set as Tariff Switch.

0=Digital Input*

1=Pulse Counter

2=Tariff Switch

DIx Debounce

Specifies the minimum duration the DI must remain in the Active or Inactive state before a state change is considered to be valid.

1 to 1000 (ms)

(Default=20ms)

DIx Pulse Weight

Specifies the incremental value for each received pulse. This is only used when a DI is configured as a Pulse Counter.

1* to 1,000,000

Chapter 4 Applications

4.1 Inputs and Outputs

4.1.1 Digital Inputs

The PMC-53A comes optionally with four or six self-excited Digital Inputs that are internally wetted at 24 VDC with a sampling frequency of 1000Hz and programmable debounce. The PMC-53A provides the following programmable functions for its digital inputs:

1) Digital Input The digital inputs are typically used for status monitoring which

can help prevent equipment damage, improve maintenance, and track security breaches. The real-time statuses of the Digital Inputs are available on the front panel LCD Display as well as through communications. Changes in Digital Input status are stored as events in the SOE Log in 1 ms resolution.

2) Pulse Counting Pulse counting is supported with programmable pulse weight and

facilitates WAGES (Water, Air, Gas, Electricity and Steam) information collection.

3) Tariff Switching Up to 3 Digital Inputs may be used to select to which of the 8 Tariffs

the energy consumption should be accumulated. The 3 Digital Inputs (DI1, DI2 and DI3) represent 3 binary digits where Tariff 1=000, Tariff 2=001, …, Tariff 8=111 where DI1 represents the least significant digit and DI3 represents the most significant digit. The

DI1 Function setup register must first be programmed as a Tariff Switch before configuring DI2 with the same function. In other words, if DI1 is configured as a Digital Input or Energy Pulse Counter and DI2 is configured as a Tariff Switch, the TOU will

continue to function based on the TOU Schedule. This feature is available in Firmware V1.00.03 or later.

The following table describes the DI’s setup parameters:

Default*

Table 4-1 DI Setup Parameters

4.1.2 Digital Outputs

The PMC-53A comes optionally with two or four Form A Electrometrical Relays or Solid State Relays. Digital Outputs are normally used for setpoint alarming, load control, or remote control applications.

Digital Outputs on the PMC-53A can be used in the following applications:

36

CET Electric Technology

1) Front Panel Control Manually operated from the front panel. Please refer to the DO

Control setup parameter in Section 3.3.3 for a detailed description.

2) Remote Control Remotely operated over communications via our free PMC Setup

software or PecStar® iEMS Integrated Energy Management System.

3) Control Setpoint Control Setpoints can be programmed to trigger DO action upon

becoming active. Please refer to Section 4.4 for a detailed description.

Since there are multiple ways to trigger the Digital Outputs on the PMC-53A, a prioritized scheme has been developed to avoid conflicts between different applications. In general, Front Panel Control has the highest priority and can override other control schemes. Remote Control and Control Setpoint share the same priority, meaning that they can all be programmed to control the same Digital Output. This scheme is equivalent to having an implicit Logical OR operation for the control of a Digital Output and may be useful in providing a generic alarm output signal. However, the sharing of a Digital Output is not recommended if the user intends to generate a control signal in response to a specific setpoint condition.

4.1.3 Energy Pulse Outputs

The PMC-53A comes standard with one front panel LED Pulse Output for energy pulsing and can be equipped with two or four optional Solid State Relay Outputs for kWh and kvarh pulsing. Energy Pulse Outputs are typically used for accuracy testing. Energy Pulsing via the front panel LED can be enabled from the front panel through the LED EN Pulse setup parameter. The pulse constant can be configured as 1000/3200 pulses per kWh or kvarh through the EN Pulse CNST setup parameter.

4.1.4 Analog Input

The PMC-53A comes optionally with an Analog Input which can be programmed as 0mA to 20mA or 4mA to 20mA input. There are 3 setup parameters:

Type: Select between 0-20mA or 4-20mA input. AI Zero: This value corresponds to the minimum Analog Input of 4 mA (for 4-20mA input) and

has a range of -999,999 to +999,999.

AI Full: This value corresponds to the maximum Analog Input of 20 mA and has a range of -

999,999 to +999,999. For example, to measure the oil temperature of a transformer, connect the outputs of the temperature sensor to the AI terminals of the PMC-53A. The temperature sensor outputs 4mA when the temperature is -25°C and 20mA when the temperature is 100°C. As such, the Type parameter should be programmed as 4-20mA. The AI FULL parameter should be programmed with the value 100, and the AI ZERO parameter should be programmed with the value -25. Therefore, when the output of the sensor is 20mA, the reading will be 100.00°C. When the output is 4mA, the reading will be -25.00°C. When the output is 12mA, the reading will be (100°C - (-25°C)) x (12mA-4mA) / (20mA-4mA) + (-25°C) = 37.50°C.

4.1.5 Analog Output

The PMC-53A comes optionally with one Analog Output which can be programmed as 0mA to 20mA or 4mA to 20mA output.

37

CET Electric Technology

Parameter

Phase A

Phase B

Phase C

Total

Average

Uln

● ● ● - ●

Ull

● ● ● - ●

Current

● ● ● - ●

Neutral Current

- - -

In (Calculated)

I4 (Optional)

Residual

Current~

- - -

Ir~

kW

● ● ● ● -

kvar

● ● ● ● -

kVA

● ● ● ● -

Power Factor

● ● ● ● -

Frequency

● - - - -

U Fundamental*

● ● ●

I Fundamental*

● ● ●

U Sequence*

U1 (Positive Sequence)

U2 (Negative Sequence)

U0 (Zero Sequence)

I Sequence*

I1 (Positive Sequence)

I2 (Negative Sequence)

I0 (Zero Sequence)

There are 4 setup parameters:

Type: Select between 0-20mA or 4-20mA output. AO Zero: Defines the zero scale value of the parameter when the Analog Output is 0 or 4 mA

according to the AO Type. The value ranges between -999,999 to +999,999.

AO Full: Defines the full scale value of the parameter when the Analog Output is 20 mA. The

value ranges between -999,999 and +999,999.

Key: Defines the parameter to which the Analog Output is proportional. The Analog Output

Parameters are listed in Table 3-13.

For example, an AO of 4-20mA is required to be proportional to Phase A current. The maximum value of phase A current is 2000A, and the minimum value is 500A. As such, the Type parameter should be programmed as 4-20mA. The Key parameter should be programmed with Ia (Phase A Current). The AO FULL parameter should be programmed with the value 2000. The AO ZERO parameter should be programmed with the value 500. Therefore, when Phase A Current is 500A or below, The AO output is 4mA. When Phase A Current is 2000A, the AO output is 20mA. When Phase A Current is 1250A, the AO is (1250A-500A) x (20mA-4mA) / (2000A-500A) + 4mA = 12.00 (mA).

4.1.6 RTD Input

The PMC-53A optionally provides two RTD Inputs for temperature measurements. The PT100 sensors are optional and not included. The 2-wire outputs of the PT100 sensor are connected to the RTD Input of the PMC-53A if so equipped. The PMC-53A can provide accurate temperature monitoring with the optional RTD inputs for measuring the temperature of the Neutral Conductor, Transformer or other equipment. There is a RTD Compensation register for each channel which can be used to compensate the measurement accuracy, and the compensation can be set according to formula:

RTD Compensation = 0.29xL where L ≤ 8 is the PT100 sensor’s cable length in m

4.2 Power and Energy

4.2.1 Basic Measurements

The PMC-53A provides the following basic measurements which are available through the Front Panel or communications.

* Available in Firmware V1.00.03 or later. ~ Available in Firmware V1.00.06 or later.

Table 4-2 Basic Measurements

38

CET Electric Technology

3-Phase Energy

kWh Import/Export/Net/Total kWh Import/Export of TOU T1-8

kvarh Import/Export/Net/Total kvarh Import/Export of TOU T1-8 kvarh of Q1/Q2/Q3/Q4

kVAh Total kVAh Total of TOU T1-8

Per-Phase Energy

(Phase A/B/C):

kWh Import/Export/Net/Total kWh Import/Export of TOU T1-8

kvarh Import/Export/Net/Total kvarh Import/Export of TOU T1-8 kvarh of Q1/Q2/Q3/Q4

kVAh kVAh of TOU T1-8

Setup Parameter

Definition

Options

Demand Period

1 to 60 minutes. For example, if the # of Sliding Windows is set as 1 and the Demand Period is 15, the demand cycle will be 1×15=15min.

1 to 60 min

Default=15

# of Sliding Windows

Number of Sliding Windows.

1 to 15

Default=1

Self-Read Time

The Self-Read Time allows the user to specify the time and day of the month for the Peak Demand Self-Read operation. The Self-Read Time supports three options:

Default=0xFFFF

4.2.2 Energy Measurements

The PMC-53A provides Energy parameters for active energy (kWh), reactive energy (kvarh) and apparent energy (kVAh) with a resolution of 0.1k and a maximum value of ±100,000,000.0. When the maximum value is reached, the energy registers will automatically roll over to zero. The energy can be reset manually through the Front Panel or via communications. Further, the energy can be preset to user defined values via communications.

The PMC-53A provides the following energy measurements:

Table 4-3 Energy Measurement

4.2.3 Interval Energy Measurements

The PMC-53A provides Interval Energy measurements of kWh Import/Export, kvar Import/Export and kVAh since Firmware V1.00.03. The Interval Energy measurements represent the amount of energy consumed during the last completed interval as defined by EN Period. The Interval Energy Measurements can only be retrieved through communications and are not available on the Front Panel.

The Interval Energy Period (EN Period) setup parameter can be programmed from the Front Panel or through communications and allows the user to specify the interval for which the real-time energy consumption should be accumulated. Please note that changing the Interval Energy Period would clear the present Interval Energy measurements.

4.2.4 Demand Measurements

Demand is defined as the average power consumption over a fixed interval (usually 15 minutes) based on the sliding window method. The PMC-53A provides Present Demand and Predicted Demand for Ia, Ib, Ic, kW Total, kvar Total and kVA Total as well as kW Total, kvar Total and kVA Total of TOU Tariff 1 to

8. Only Import Demand is provided for kW Total, kvar total and kVA Total. Predicted Demand is typically used for pre-alarming and to help users reduce power consumption using a Setpoint to warn that the Demand limit may be exceeded.

The PMC-53A provides the following setup parameters:

39

CET Electric Technology

 A zero value means that the Self-Read will take place at

00:00 of the first day of each month.

 A non-zero value means that the Self-Read will take place

at a specific time and day based on the formula: Self-Read

Time = Day * 100 + Hour where 0 ≤ Hour ≤ 23 and 1 ≤ Day ≤ 28. For example, the value 1512 means that the Self-

Read will take place at 12:00pm on the 15th day of each month.

 A 0xFFFF value will disable the Self-Read operation and

replace it with Manual operation. A manual reset will cause the Max. Demand of This Month to be transferred to the Max. Demand of Last Month and then reset. The terms This Month and Last Month will become Since Last

Reset and Before Last Reset.

Predicted Response

The Predicated Response shows the speed of the predicted demand output. A value between 70 and 99 is recommended for a reasonably fast response. Specify a higher value for higher sensitivity.

70 to 99

Default=70

Table 4-4 Demand Setup

4.3 Power Quality

4.3.1 Phase Angles

Phase analysis is used to identify the angle relationship between 3-phase Voltages and Currents.

For WYE connected systems, the per phase difference of the Current and Voltage angles should correspond to the per phase PF. For example, if the PF is 0.5 Lag and the Voltage phase angles are 0.0°,

240.0° and 120.0°, the Current phase angles should have the values of -60.0°, 180.0° and 60.0°.

4.3.2 Power Quality Parameters

The PMC-53A provides the following PQ parameters:

4.3.2.1 Harmonics

The PMC-53A provides harmonic analysis for THD, TOHD, TEHD and individual harmonics up to the 31st order. All harmonic parameters are available on the Front Panel and through communications. In addition, the PMC-53A also provides TDD, K-factor and Crest-factor measurements for Current.

4.3.2.2 TDD

To tal Demand Distortion (TDD) is defined as the ratio of the RMS (Root Mean Square) of the Harmonic

Current to the RMS of the Rated or Maximum Fundamental Current Demand. TDD of Current is calculated by the formula below:

where

IL = Maximum Fundamental Current Demand h = Harmonic Order (1, 2, 3, 4, etc.) I

= RMS Load Current at the nth Harmonic

h

4.3.2.3 K-Factor

K-Factor is defined as the weighted sum of the Harmonic Load Current according to their effects on transformer heating, as derived from ANSI/IEEE C57.110. A K-Factor of 1.0 indicates a linear load (no

40

CET Electric Technology

)(

K

2

hh

1h

2

hh

1h

max

h

I

hI

Factor







x

rms

peak

C 

Phase A/AB

Phase B/BC

Phase C/CA

Harmonic-Voltage

THD

TEHD

TOHD

2

nd

Harmonics

2

nd

Harmonics

2nd Harmonics

…

31st Harmonics

Harmonic-Current

THD

TEHD

TOHD

TDD

TEDD

TODD

K-factor

Crest-factor

2

nd

Harmonics

2

nd

Harmonics

2nd Harmonics

…

31st Harmonics

100%

V1

V2



100%

I1

I2



harmonics). The higher the K-Factor, the greater the harmonic heating effect.

where

Ih = hth Harmonic Current in RMS h

= Highest harmonic order

max

4.3.2.4 Crest Factor

Crest Factor is defined as the Peak to Average Ratio (PAR), and its calculation is illustrated below:

where

|X|

= Peak amplitude of the waveform

peak

X

= RMS value

rms

The following table illustrates the available Voltage and Current Harmonics measurements on the PMC53A.

Table 4-5 Harmonic Measurements

4.3.3 Unbalance

The PMC-53A provides Voltage and Current Unbalance measurements. The calculation method of Voltage and Current Unbalances are listed below:

Voltage Unbalance =

where V1, V2 are the Positive and Negative Sequence Components for Voltage, respectively. and I1, I2 are the Positive and Negative Sequence Components for Current, respectively.

Current Unbalance =

41

CET Electric Technology

4.4 Setpoints

The PMC-53A comes standard with 9 user programmable Setpoints which provide extensive control by allowing a user to initiate an action in response to a specific condition. Typical setpoint applications include alarming, fault detection and power quality monitoring.

Figure 4-1 Over Setpoint

Figure 4-2 Under Setpoint

Setpoints can be programmed via the Front Panel or through communications and have the following setup parameters:

42

CET Electric Technology

Setup Parameter

Definition

Options/Default*

Setpoint Type

Over or Under Setpoint.

0=Over Setpoint* 1=Under Setpoint

Setpoint Parameter

Specify the parameter to be monitored.

See Table 4-7

Over Limit

Specify the value that the setpoint parameter must exceed for Over Setpoint to become active or for Under Setpoint to become inactive.

0*

Under Limit

Specify the value that the setpoint parameter must go below for Over Setpoint to become inactive or for Under Setpoint to become active.

0*

Active Delay

Specify the minimum duration that the setpoint condition must be met before the setpoint becomes active. An event will be generated and stored in the SOE Log. The range of the Active Delay is between 0 and 9999 seconds.

0 to 9999s

Default=10

Inactive Delay

Specify the minimum duration that the setpoint return condition must be met before the setpoint becomes inactive. An event will be generated and stored in the SOE Log. The range of the Inactive Delay is between 0 and 9999 seconds.

0 to 9999

Default=10

Setpoint Trigger

Specify what action a setpoint would take when it becomes active. Please refer to Table 4-8 below for a list of Setpoint Triggers.

See table 4-8

Key

Setpoint Parameter

Scale

Unit

0

None

- - 1

Uln (Any Phase Voltage)

x1

V

2

Ull (Any Line Voltage)

3

I (Any Phase Current)

A

4

In (Calculated)

5

Frequency

Hz

6

P (kW Total)

W

7

Q (kvar Total)

var

8

S (kVA Total)

VA

9

PF (PF Total)

-

10

P DMD (kW Total Present Demand)

W

11

Q DMD (kvar Total Present Demand)

var

12

S DMD (kVA Total Present Demand)

VA

13

P DMD Pred (kW Total Predicted Demand)

W

14

Q DMD Pred (kvar Total Predicted Demand)

var

15

S DMD Pred (kVA Total Predicted Demand)

VA

16

U THD

100%

17

U TOHD

100%

18

U TEHD

100%

19

I THD

100%

20

I TOHD

100%

21

I TEHD

100%

22

U Unbal (Voltage Unbalance)

100%

23

I Unbal (Current Unbalance)

100%

24

Reversal (Phase Reversal)3

- 25

I4 (Measured)*

x1

A

26

AI*

-

27

Reserved

- - 28

RTD1*

x1

°C

29

RTD2*

30

Ir (Residual Current)~

x1 A 31

U2 (-ve Sequence Unbalance)~

x1

V

32

U0 (Zero Sequence Unbalance)~

Table 4-6 Description for Setpoint Parameters

In addition, the LCD would blink when there is an active setpoint alarm if the SP LCD Alarm (Register #6048) is set to Enable via the Front Panel or through communications.

* Valid only if the device is equipped with the appropriate option ~ Available in Firmware V1.00.06 or later

Table 4-7 Setpoint Parameters

43

CET Electric Technology

Key

Action

Key

Action

0

None

3

DO3 Closed

1

DO1 Closed

4

DO4 Closed

2

DO2 Closed

Others

Reserved

Max./Min. Parameters

Ia

Ib

Ic

I avg

Uan

Ubn

Ucn

Uln avg

Uab

Ubc

Uca

Ull avg

kWa

kWb

kWc

kW Total

kvara

kvarb

kvarc

kvar Total

kVAa

kVAb

kVAc

kVA Total

PFa

PFb

PFc

PF Total

Frequency

I4

Ia THD

Ib THD

Ic THD

Uan/Uab THD

Ubn/Ubc THD

Ucn/Uca THD

Ia K-Factor

Ib K-Factor

Ic K-Factor

Ia Crest-factor

Ib Crest-factor

Ic Crest-factor

U Unbal.

I Unbal.

In

(Calculated)

Ir*

Peak Demand Logs of This Month (Since Last Reset) and Last Month (Before Last Reset)

Ia

Ib

Ic

Table 4-8 Setpoint Triggers

Only when DOx Mode is set to Remote Control/Setpoint would setting the Setpoint Trigger to DOx Closed valid. In addition,

 Only when the PMC-53A’s Basic Function option is “3” (4xDI+3xRelay Output) or “A”

(4xDI+2xSS Pulse Output) would setting the Setpoint Trigger to DO1 Closed or DO2 Closed have meaning.

 Only when the Expansion Module B is equipped with the “2xDI + 2xDO (Relay Output)” or

“2xDI + 2xSS Pulse Output” options would setting the Setpoint Trigger to DO3 Closed or DO4

Closed have meaning.

4.5 Logging

4.5.1 Max./Min. Log

The PMC-53A records the Max. Log and Min. Log of This Month (Since Last Reset) and Last Month (Before Last Reset) with timestamp for 45 parameters. Each log includes the relevant parameter value

and its timestamp. The recorded data is stored in non-volatile memory and will not suffer any loss in the event of a power failure. The PMC-53A’s Max./Min. Log records the following parameters:

* Available in Firmware V1.00.06 or later

Table 4-9 Max./Min. Log

The same Self-Read Time for the Peak Demand Log is used to specify the time and day of the month for the Max./Min. Self-Read operation. Please refer to Section 4.2.4 for a complete description of the Self-Read Time and its operation. The Max./Min. Log of This Month can be reset manually from the Front Panel or via communications.

4.5.2 Peak Demand Log

The PMC-53A records the Peak Demand of This Month (Since Last Reset) and Last Month (Before Last Reset) with timestamp for Ia, Ib, Ic, kW Total, kvar Total and kVA Total as well as kW Total, kvar Total and

kVA Total for TOU Tariffs 1 to 8. The Peak Demand of This Month (Since Last Reset) can be accessed from the Front Panel as well as communications while the Peak Demand of Last Month (Before Last Reset) can only be retrieved through communications. Please refer to Section 4.2.4 for a complete description of the Self-Read Time and its operation.

44

CET Electric Technology

kW Total

kvar Total

kVA Total

kW Total for TOU Tariffs 1 to 8

kvar Total for TOU Tariffs 1 to 8

kVA Total for TOU Tariffs 1 to 8

Active Energy

kWh Import

kWh Export

kWh Net

kWh Total

T1 kWh Import

T2 kWh Import

T3 kWh Import

T4 kWh Import

T5 kWh Import

T6 kWh Import

T7 kWh Import

T8 kWh Import

T1 kWh Export

T2 kWh Export

T3 kWh Export

T4 kWh Export

T5 kWh Export

T6 kWh Export

T7 kWh Export

T8 kWh Export

Reactive Energy

kvarh Import

kvarh Export

kvarh Net

kvarh Total

T1 kvarh Import

T2 kvarh Import

T3 kvarh Import

T4 kvarh Import

T5 kvarh Import

T6 kvarh Import

T7 kvarh Import

T8 kvarh Import

T1 kvarh Export

T2 kvarh Export

T3 kvarh Export

T4 kvarh Export

T5 kvarh Export

T6 kvarh Export

T7 kvarh Export

T8 kvarh Export

kvarh Q1

kvarh Q2

kvarh Q3

kvarh Q4

Apparent Energy

kVAh

T1 kVAh

T2 kVAh

T3 kVAh

T4 kVAh

T5 kVAh

T6 kVAh

T7 kVAh

T8 kVAh

Freeze Type

Parameters

Depth

Daily Freeze

kWh Total, kvarh Total, kVAh Total

Peak Demands for kW Total, kvar Total and kVA Total

60

Monthly Freeze

kWh Total, kvarh Total, kVAh Total

Peak Demands for kW Total, kvar Total and kVA Total with Timestamp

36

Table 4-10 Peak Demand Log

4.5.3 Monthly Energy Log

The PMC-53A stores monthly energy data for the present month and the last 12 months. The Monthly Energy Log Self-read Time setup parameter allows the user to specify the time and day of the month

for the Recorder’s Self-read operation via communications. The Monthly Energy Logs are stored in the meter’s non-volatile memory and will not suffer any loss in the event of power failure, and they are

stored on a First-In-First-Out basis where the newest log will overwrite the oldest.

The Monthly Energy Log Self-Read Time supports two options:

A zero value means that the Self-Read will take place at 00:00 of the first day of each month. A non-zero value means that the Self-Read will take place at a specific time and day based on the

formula: Energy Self-Read Time = Day x 100 + Hour where 0 ≤ Hour ≤ 23 and 1 ≤ Day ≤ 28. For example, the value 1512 means that the Self-Read will take place at 12:00pm on the 15th day of each month. The Monthly Energy Logs can be reset manually through the front panel or via communications. The PMC-53A provides the following energy data for the present month and the last 12 months:

Table 4-11 Energy Measurements for each Monthly Energy Log Record

4.5.4 Daily and Monthly Freeze Log (Optional)

The PMC-53A optionally provides a Daily Freeze Log and a Monthly Freeze Log for Energy and Demand parameters and can store up to 60 daily freeze records (2 months) and 36 monthly freeze records (3 years). All Freeze Logs and their respective setup registers can only be accessed through communications. The PMC-53A’s Freeze Logs can freeze and record the following parameters:

Table 4-12 Freeze Log

The Daily Self-Read Time setup parameter allows the user to specify the time of the day for the Daily Freeze Log Self-Read operation, while the Monthly Self-Read Time setup parameter allows the user to

45

CET Electric Technology

Setup Parameters

Value/Option

Default

Trigger Mode

0=Disabled / 1=Triggered by Timer

1

Recording Mode

0=Stop-When-Full / 1=First-In-First-Out

1

Recording Depth

1 to 10,000 (entry)

5760

Recording Interval

60 to 3,456,000 seconds

900 s

Offset Time

0 to 43,200 seconds, 0 indicates no offset

0

Number of Parameters

0 to 16

16

Parameter 1 to 16

See Appendix A for a complete list of parameters

See Appendix B

specify the time and day of the month for the Monthly Freeze Log Self-Read operation.

1) Daily Freeze Self-Read Time can be set to a zero value or a non-zero value:

 A zero value means that the Self-Read will take place at 00:00 everyday.  A non-zero value means that the Self-Read will take place at a specific time of the day based on

the formula: Self-Read time = (Hour x 100 + Min) where 0 ≤ Hour ≤ 23 and 0 ≤ Min ≤ 59. For example, the value 1512 means that the Self-Read will take place at 15:12 of each day.

2) Monthly Freeze Self-Read Time can be set to a zero value or a non-zero value:

 A zero value means that the Self-Read will take place at 00:00 of the first day of each month.  A non-zero value means that the Self-Read will take place at a specific time and day based on

the formula: Monthly Self-Read Time = Day x 100 + Hour where 0 ≤ Hour ≤ 23 and 1 ≤ Day ≤ 28. For example, the value 1512 means that the Self-Read will take place at 12:00pm on the 15th day of each month.

4.5.5 SOE Log

The PMC-53A’s SOE Log can store up to 100 events such as Power-on, Power-off, Digital Input status changes, Digital Output status changes, Setup changes and Setpoint events in its non-volatile memory. Each event record includes the event classification, its relevant parameter values and a timestamp in ±1 ms resolution. The SOE Log can be displayed on the Front Panel and retrieved via communications. If there are more than 100 events, the newest event will replace the oldest event on a First-In-First-Out basis. The SOE Log can be reset from the Front Panel or via communications.

4.5.6 Data Recorder (DR) Log (Optional)

The PMC-53A optionally provides five Data Recorders capable of recording a maximum of 16 parameters each. The Data Recorder Log is stored in the device’s non-volatile memory and will not suffer any loss in the event of a power failure. The programming of the Data Recorder is only supported over communications. Each Data Recorder provides the following setup parameters:

Table 4-13 Setup Parameters for Data Recorder

The Data Recorder Log is only operational when the values of Trigger Mode, Recording Depth, Recording Interval, and Number of Parameters are all non-zero.

The Recording Offset parameter can be used to delay the recording by a fixed time from the Recording Interval. For example, if the Recording Interval parameter is set to 3600 (hourly) and the Recording Offset parameter is set to 300 (5 minutes), the recording will take place at 5 minutes after the hour

every hour, i.e. 00:05, 01:05, 02:05…etc. The value of the Recording Offset parameter should be less than the Recording Interval parameter.

46

CET Electric Technology

Tariff

DI Function

DI1 = Tariff Switch

DI2 & DI1 = Tariff Switch

DI3, DI2 & DI1 = Tariff Switch

T1

DI1 (0=T1)

DI2 + DI1 (00=T1)

DI3 + DI2 + DI1 (000=T1)

T2

DI1 (1=T2)

DI2 + DI1 (01=T2)

DI3 + DI2 + DI1 (001=T2)

T3

Not Available

DI2 + DI1 (10=T3)

DI3 + DI2 + DI1 (010=T3)

T4

Not Available

DI2 + DI1 (11=T4)

DI3 + DI2 + DI1 (011=T4)

T5

Not Available

DI3 + DI2 + DI1 (100=T5)

T6

Not Available

DI3 + DI2 + DI1 (101=T6)

T7

Not Available

DI3 + DI2 + DI1 (110=T7)

T8

Not Available

DI3 + DI2 + DI1 (111=T8)

Setup Parameters

Definition

Options

Daily Profile #

Specify a daily rate schedule which can be divided into a maximum of 12 periods in 15-min intervals. Up to 20 Daily Profiles can be programmed for each TOU schedule.

1 to 20, the first period starts at 00:00 and the last period ends at 24:00.

Season #

A year can be divided into a maximum of 12 seasons. Each season is specified with a Start Date and ends with the next season’s Start Date.

1 to 12, starts from January 1st

Alternate Days #

A day can be defined as an Alternate Day, such as May 1st. Each Alternate Day is assigned a Daily Profile.

1 to 90.

Day Types

Specify the day type of the week. Each day of a week can be assigned a day type such as Weekday1, Weekday2, Weekday3 and Alternate Days. The Alternate Day has the highest priority.

Weekday1, Weekday2, Weekday3 and Alternate Days

4.6 Time of Use (TOU)

TOU is used for electricity pricing that varies depending on the time of day, day of week, and season. The TOU system allows the user to configure an electricity price schedule inside the PMC-53A and accumulate energy consumption into different TOU tariffs based on the time of consumption. TOU programming is only supported through communications.

The TOU feature on PMC-53A supports two TOU schedules, which can be switched at a pre-defined time. Each TOU schedule supports:

 Up to 12 seasons  90 Holidays or Alternate Days  20 Daily Profiles, each with 12 Periods in 15-minute interval  8 Tariffs

Instead of using the TOU schedule to switch between Tariffs, the PMC-53A supports Tariff switching based on the status of DI1 to DI3 in Firmware V1.00.03 or later.

The 3 Digital Inputs (DI1, DI2 and DI3) represent 3 binary digits where Tariff 1=000, Tariff 2=001, Tariff 3= 010, …Tariff 7=110 and Tariff 8=111 where DI1 represents the least significant digit and DI3 represents the most significant digit. As soon as DI1, DI2 and/or DI3 are configured as Tariff Switches, the current TOU Tariff will be determined by the status of the DIs, and the TOU Schedule will be ignored. The DI1 Function setup register must first be programmed as a Tariff Switch before configuring DI2 and DI3 with the same function. In other words, if DI1 is configured as a Digital Input or Energy Pulse Counter, and DI2 is configured as a Tariff Switch, the TOU will continue to function based on the TOU Schedule. The number of Tariffs supported depends on how many DIs are programmed as a Tariff Switch as indicated in the following table.

Table 4-14 DIs and the Number of Tariffs Setup

Each TOU schedule has the following setup parameters and can only be programmed via communications:

47

CET Electric Technology

Switching Time

Specify when to switch from one TOU schedule to another. Writing 0xFFFFFFFF to this parameter disables switching between TOU schedules.

Format: YYYYMMDDHH Default=0xFFFFFFFF

Bit

Event

B00

Summary Bit (Set if any other bit is set)

B01

Frequency is out of range (45 to 65Hz) (3P4W or 3P3W)

B02

Any phase voltage < 10% of PT Primary (Register 6000) (3P4W only)

B03

Any phase current < 10% of CT Primary (Register 6004) (3P4W or 3P3W)

B04

RTD 1 broken (RTD Input option only)

B05

RTD 2 broken (RTD Input option only)

B06

Voltage Phase Reversal (3P4W only)

B07

Current Phase Reversal (3P4W or 3P3W)

B08

Negative kW Total may be abnormal (3P4W or 3P3W)

B09

Negative kWa may be abnormal (3P4W only)

B10

Negative kWb may be abnormal (3P4W only)

B11

Negative kWc may be abnormal (3P4W only)

B12

CTa polarity may be reversed (3P4W only)

B13

CTb polarity may be reversed (3P4W only)

B14

CTc polarity may be reversed (3P4W only)

B15

Reserved

Table 4-15 TOU Setup Parameters

For each of the 8 Tariff Rates, the PMC-53A provides the following information:

Energy: kWh Import/Export, kvarh Import/Export, kVAh – Per Phase and Total

Peak Demand: kW/kvar/kVA of This Month (Since Last Reset) and Last Month (Before Last Reset).

TOU data is available through the front panel and communications.

4.7 Diagnostics

The PMC-53A provides wiring error detection for 3P4W and 3P3W wiring modes, which allow users to check for possible problems especially during the initial commissioning stage. The following wiring errors may be detected:

 Frequency Out-of-Range  Voltage / Current Phase Loss  Incorrect Voltage and Current Phase Sequence  kW Direction per phase and Total  Possible Incorrect CT Polarity  Broken RTD

Please note the detections above are based on the assumptions below:

 The Voltage and Current Phase Sequence are consistent  kW is kW Import, which means the kW is over 0  The wiring is correct  3P4W wiring mode supports all detections  3P3W wiring mode does not support the detection of Voltage Phase Loss, kW Direction per phase

and CT Polarity The Diagnostic register (0101) indicates the status of the wiring error detection with a bit value of 1 meaning active and 0 meaning inactive which are illustrated in table below:

Table 4-16 Wiring Diagnostic Register

48

CET Electric Technology

Format

Description

UINT16/INT16

Unsigned/Signed 16-bit Integer

UINT32/INT32

Unsigned/Signed 32-bit Integer

Float

IEEE 754 32-bit

Single Precision Floating Point Number

Register

Property

Description

Format

Scale

Unit

0000

RO

Uan

Float

x1

V

0002

RO

Ubn

Float

0004

RO

Ucn

Float

0006

RO

Uln Average

Float

0008

RO

Uab

Float

0010

RO

Ubc

Float

0012

RO

Uca

Float

0014

RO

Ull Average

Float

0016

RO

Ia

Float A 0018

RO

Ib

Float

0020

RO

Ic

Float

0022

RO

I Average

Float

0024

RO

kWa

Float W 0026

RO

kWb

Float

0028

RO

kWc

Float

0030

RO

kW Total

Float

0032

RO

kvara

Float

var

0034

RO

kvarb

Float

0036

RO

kvarc

Float

0038

RO

kvar Total

Float

0040

RO

kVAa

Float

VA

0042

RO

kVAb

Float

0044

RO

kVAc

Float

0046

RO

kVA Total

Float

0048

RO

PFa

Float - 0050

RO

PFb

Float - 0052

RO

PFc

Float - 0054

RO

PF Total

Float - 0056

RO

Frequency

Float

Hz

0058

RO

Uan/Uab (3P3W) Angle

Float ° 0060

RO

Ubn/Ubc (3P3W) Angle

Float ° 0062

RO

Ucn/Uca (3P3W) Angle

Float ° 0064

RO

Ia Angle

Float ° 0066

RO

Ib Angle

Float ° 0068

RO

Ic Angle

Float

°

0070

RO

In (Calculated)

Float A 0072

RO

I41

Float

0074

RO

Displacement PFa

Float

-

Chapter 5 Modbus Register Map

This chapter provides a complete description of the Modbus register map (Protocol Version 1.4) for the PMC-53A to facilitate the development of 3rd party communications driver for accessing information on the PMC-53A. For a complete Modbus Protocol Specification, please visit http://www.modbus.org. The PMC-53A supports the following Modbus functions:

1) Read Holding Registers (Function Code 0x03)

2) Force Single Coil (Function Code 0x05)

3) Preset Multiple Registers (Function Code 0x10)

The following table provides a description of the different data formats used for the Modbus registers. The PMC-53A uses the Big Endian byte ordering system.

5.1 Basic Measurements

49

CET Electric Technology

0076

RO

Displacement PFb

Float

-

0078

RO

Displacement PFc

Float

-

0080

RO

Displacement PF Total

Float

-

0082

RO

AI1 Scaled

Float

-

0084

RO

Reserved

Float

-

0086

RO

RTD 11

Float

︒C

0088

RO

RTD 21

Float

0090

RO

AO1

Float

-

0092

RO

Reserved

Float

-

0094

RO

Reserved

Float

-

0096

RO

DI Status

1,2

UINT16

-

0097

RO

Reserved

UINT16

-

0098

RO

DO Status

1,3

UINT16

-

0099

RO

Reserved

UINT16

-

0100

RO

Setpoint Status4

UINT16

-

0101

RO

Wiring Diagnostic Status5

UINT16

-

0102

RO

SOE Log Pointer6

UINT32

-

0104

RO

Device Operating Time

7

UINT32

x0.1

0.1Hour

0106-0111

RO

Reserved

UINT32 -

0112

RO

Phase A Fundamental kW

Float

x1

W

0114

RO

Phase B Fundamental kW

Float

0116

RO

Phase C Fundamental kW

Float

0118

RO

Fundamental kW Total

Float

0120

RO

Total Harmonic kW

Float

0122

RO

DR #1 Log Pointer

1,6

UINT32 - -

0124

RO

DR #2 Log Pointer

1,6

UINT32 - -

0126

RO

DR #3 Log Pointer

1,6

UINT32 - -

0128

RO

DR #4 Log Pointer

1,6

UINT32 - -

0130

RO

DR #5 Log Pointer

1,6

UINT32 - -

0132-0148

RO

Reserved

UINT32 -

0150

RO

Uan/Uab Fundamental*

Float

x1

V

0152

RO

Ubn/Ubc Fundamental*9

Float

0154

RO

Ucn/Uca Fundamental*9

Float

0156

RO

Ia Fundamental*

Float

x1

A

0158

RO

Ib Fundamental*9

Float

0160

RO

Ic Fundamental*9

Float

0162

RO

U1 (Positive Sequence Voltage)*10

Float

x1

V

0164

RO

U2 (Negative Sequence Voltage)*10

Float

0166

RO

U0 (Zero Sequence Voltage)*10

Float

0168

RO

I1 (Positive Sequence Current)*10

Float

x1

A

0170

RO

I2 (Negative Sequence Current)*10

Float

0172

RO

I0 (Zero Sequence Current)*10

Float

0174

RO

Ir (Residual Current)#

Float

Bit15

Bit14

Bit13

Bit12

Bit11

Bit10

Bit9

Bit8

Reserved

Setpoint9

Bit7

Bit6

Bit5

Bit4

Bit3

Bit2

Bit1

Bit0

Setpoint8

Setpoint7

Setpoint6

Setpoint5

Setpoint4

Setpoint3

Setpoint2

Setpoint1

* Available in Firmware V1.00.03 or later

#

Available in Firmware V1.00.06 or later

Notes:

1) I4, AI, RTD1, RTD2, AO, DI Status, DO Status and DRx Log Pointers are only meaningful if the

meter is equipped with the corresponding option.

2) For the DI Status register, the bit values of B0 to B5 represent the states of DI1 to DI6,

respectively, with “1” meaning Active (Closed) and “0” meaning Inactive (Open).

3) For the DO Status register, the bit values of B0 to B3 represent the states of DO1 to DO4,

respectively, with “1” meaning Active (Closed) and “0” meaning Inactive (Open).

4) For the Setpoint Status register, the bit values indicate the various Setpoint states with “1”

meaning Active and “0” meaning Inactive. The following table illustrates the details of the Alarm Status register.

5) The following table illustrates the Wiring Diagnostic Status with 0 meaning Normal and 1 meaning

Abnormal:

Table 5-1 Basic Measurements

Table 5-2 Alarm Status Register

50

CET Electric Technology

Bit

Event

B00

Summary Bit (Set if any other bit is set)

B01

Frequency is out of range (45 to 65Hz) (3P4W or 3P3W)

B02

Any phase voltage < 10% of PT Primary (Register 6000) (3P4W only)

B03

Any phase current < 10% of CT Primary (Register 6004) (3P4W or 3P3W)

B04

RTD 1 broken (RTD Input option only)

B05

RTD 2 broken (RTD Input option only)

B06

Voltage Phase Reversal (3P4W only)

B07

Current Phase Reversal (3P4W or 3P3W)

B08

Negative kW Total may be abnormal (3P4W or 3P3W)

B09

Negative kWa is may be abnormal (3P4W only)

B10

Negative kWb may be abnormal (3P4W only)

B11

Negative kWc may be abnormal (3P4W only)

B12

CTa polarity may be reversed (3P4W only)

B13

CTb polarity may be reversed (3P4W only)

B14

CTc polarity may be reversed (3P4W only)

B15

Reserved

Register

Property

Description

Format

Scale

Unit

0500

RW

kWh Import

INT32

x0.1

kWh

0502

RW

kWh Export

INT32

Table 5-3 Wiring Diagnostic Status Register

6) The range of the Log Pointers (SOE and DRx) is between 0 and 0xFFFFFFFFH. The Log Pointer is

incremented by one for every new log generated and will roll over to 0 if its current value is 0xFFFFFFFFH. If a Clear SOE Log or Clear DRx Log is performed from the front panel or via communications, the corresponding Log Pointer will be reset to zero. Therefore, any 3rd party software should assume that a Clear Log action has been performed if it sees the SOE Log Pointer rolling over to zero or to a value that is smaller than its own pointer.

7) The Device Operating Time means the accumulated running time whenever any per-phase Current

exceeds the Current Threshold of the Device Operating Time (Register #6049). The Device Operating Time data is stored in non-volatile memory and will not suffer any loss in the event of a power failure.

8) The PMC-53A has one SOE Log and five DR Logs. Each of these logs has a Log Pointer that indicates

its current logging position. The range of the Log Pointer is between 0 and 0xFFFFFFFF, and it is incremented by one for every new log generated and will roll over to 0 if its current value is 0xFFFFFFFF. A value of zero indicates that the SOE or DRx does not contain any Log. If a Clear Log is performed via communications, its Log Pointer will be reset to zero.

Use the following equation to determine the latest log location:

Latest Log Location = Modulo [Log Pointer / Log Depth] where Log Pointer may be one of the following:

SOE Log Pointer, DR1 – DR5 Log Pointers and Log Depth is as follows:

SOE Log Depth = 100 (fixed) DRx Log Depth = DRx Recording Depth (see Section 5.11.5 Data Recorder Setup)

9) When the Wiring Mode is 1P2W L-N or 1P2W L-L, the L2 and L3 phase voltages and currents have

no meaning, and their registers are reserved.

10) When the Wiring Mode is 1P2W L-N, 1P2W L-L or 1P3W, the Sequence Components U1/I1, U2/I2

and U0/I0 have no meaning and their registers are reserved.

5.2 Energy Measurements

The Energy registers have a maximum value of 1,000,000,000 and will roll over to zero automatically when it is reached. The actual energy value is 0.1 times of the register value.

5.2.1 3-Phase Total Energy Measurements

51

CET Electric Technology

0504

RO

kWh Net

INT32

0506

RO

kWh Total

INT32

0508

RW

kvarh Import

INT32

kvarh

0510

RW

kvarh Export

INT32

0512

RO

kvarh Net

INT32

0514

RO

kvarh Total

INT32

0516

RW

kVAh

INT32

kVAh

0518

RW

kvarh Q1

INT32

kvarh

0520

RW

kvarh Q2

INT32

0522

RW

kvarh Q3

INT32

0524

RW

kvarh Q4

INT32

0526

RW

kWh Import of T1

INT32

kWh

0528

RW

kWh Export of T1

INT32

0530

RW

kvarh Import of T1

INT32

kvarh

0532

RW

kvarh Export of T1

INT32

0534

RW

kVAh of T1

INT32

kVAh

0536

RW

kWh Import of T2

INT32

kWh

0538

RW

kWh Export of T2

INT32

0540

RW

kvarh Import of T2

INT32

kvarh

0542

RW

kvarh Export of T2

INT32

0544

RW

kVAh of T2

INT32

kVAh

0546

RW

kWh Import of T3

INT32

kWh

0548

RW

kWh Export of T3

INT32

0550

RW

kvarh Import of T3

INT32

kvarh

0552

RW

kvarh Export of T3

INT32

0554

RW

kVAh of T3

INT32

kVAh

0556

RW

kWh Import of T4

INT32

kWh

0558

RW

kWh Export of T4

INT32

0560

RW

kvarh Import of T4

INT32

kvarh

0562

RW

kvarh Export of T4

INT32

0564

RW

kVAh of T4

INT32

kVAh

0566

RW

kWh Import of T5

INT32

kWh

0568

RW

kWh Export of T5

INT32

0570

RW

kvarh Import of T5

INT32

kvarh

0572

RW

kvarh Export of T5

INT32

0574

RW

kVAh of T5

INT32

kVAh

0576

RW

kWh Import of T6

INT32

kWh

0578

RW

kWh Export of T6

INT32

0580

RW

kvarh Import of T6

INT32

kvarh

0582

RW

kvarh Export of T6

INT32

0584

RW

kVAh of T6

INT32

kVAh

0586

RW

kWh Import of T7

INT32

kWh

0588

RW

kWh Export of T7

INT32

0590

RW

kvarh Import of T7

INT32

kvarh

0592

RW

kvarh Export of T7

INT32

0594

RW

kVAh of T7

INT32

kVAh

0596

RW

kWh Import of T8

INT32

kWh

0598

RW

kWh Export of T8

INT32

0600

RW

kvarh Import of T8

INT32

kvarh

0602

RW

kvarh Export of T8

INT32

0604

RW

kVAh of T8

INT32

kVAh

Register

Property

Description

Format

Scale

Unit

0620

RW

kWh Import

INT32

x0.1

kWh

0622

RW

kWh Export

INT32

0624

RO

kWh Net

INT32

0626

RO

kWh Total

INT32

0628

RW

kvarh Import

INT32

kvarh

0630

RW

kvarh Export

INT32

0632

RO

kvarh Net

INT32

0634

RO

kvarh Total

INT32

0636

RW

kVAh

INT32

kVAh

0638

RW

kvarh Q1

INT32

kWh

Table 5-4 3-phase Total Energy Measurements

5.2.2 Phase A (L1) Energy Measurements

52

CET Electric Technology

0640

RW

kvarh Q2

INT32

0642

RW

kvarh Q3

INT32

0644

RW

kvarh Q4

INT32

0646

RW

kWh Import of T1

INT32

kvarh

0648

RW

kWh Export of T1

INT32

0650

RW

kvarh Import of T1

INT32

kWh

0652

RW

kvarh Export of T1

INT32

0654

RW

kVAh of T1

INT32

0656

RW

kWh Import of T2

INT32

kWh

0658

RW

kWh Export of T2

INT32

0660

RW

kvarh Import of T2

INT32

kvarh

0662

RW

kvarh Export of T2

INT32

0664

RW

kVAh of T2

INT32

kVAh

0666

RW

kWh Import of T3

INT32

kWh

0668

RW

kWh Export of T3

INT32

0670

RW

kvarh Import of T3

INT32

kvarh

0672

RW

kvarh Export of T3

INT32

0674

RW

kVAh of T3

INT32

kVAh

0676

RW

kWh Import of T4

INT32

kWh

0678

RW

kWh Export of T4

INT32

0680

RW

kvarh Import of T4

INT32

kvarh

0682

RW

kvarh Export of T4

INT32

0684

RW

kVAh of T4

INT32

kVAh

0686

RW

kWh Import of T5

INT32

kWh

0688

RW

kWh Export of T5

INT32

0690

RW

kvarh Import of T5

INT32

kvarh

0692

RW

kvarh Export of T5

INT32

0694

RW

kVAh of T5

INT32

kVAh

0696

RW

kWh Import of T6

INT32

kWh

0698

RW

kWh Export of T6

INT32

0700

RW

kvarh Import of T6

INT32

kvarh

0702

RW

kvarh Export of T6

INT32

0704

RW

kVAh of T6

INT32

kVAh

0706

RW

kWh Import of T7

INT32

kWh

0708

RW

kWh Export of T7

INT32

0710

RW

kvarh Import of T7

INT32

kvarh

0712

RW

kvarh Export of T7

INT32

0714

RW

kVAh of T7

INT32

kVAh

0716

RW

kWh Import of T8

INT32

kWh

0718

RW

kWh Export of T8

INT32

0720

RW

kvarh Import of T8

INT32

kvarh

0722

RW

kvarh Export of T8

INT32

0724

RW

kVAh of T8

INT32

kVAh

Register

Property

Description

Format

Scale

Unit

0740

RW

kWh Import

INT32

x0.1

kWh

0742

RW

kWh Export

INT32

0744

RO

kWh Net

INT32

0746

RO

kWh Total

INT32

0748

RW

kvarh Import

INT32

kvarh

0750

RW

kvarh Export

INT32

0752

RO

kvarh Net

INT32

0754

RO

kvarh Total

INT32

0756

RW

kVAh

INT32

kVAh

0758

RW

kvarh Q1

INT32

kvarh

0760

RW

kvarh Q2

INT32

0762

RW

kvarh Q3

INT32

0764

RW

kvarh Q4

INT32

0766

RW

kWh Import of T1

INT32

kWh

0768

RW

kWh Export of T1

INT32

0770

RW

kvarh Import of T1

INT32

kvarh

0772

RW

kvarh Export of T1

INT32

0774

RW

kVAh of T1

INT32

kVAh

Table 5-5 Phase A Energy Measurements

5.2.3 Phase B (L2) Energy Measurements

53

CET Electric Technology

0776

RW

kWh Import of T2

INT32

kWh

0778

RW

kWh Export of T2

INT32

0780

RW

kvarh Import of T2

INT32

kvarh

0782

RW

kvarh Export of T2

INT32

0784

RW

kVAh of T2

INT32

kVAh

0786

RW

kWh Import of T3

INT32

kWh

0788

RW

kWh Export of T3

INT32

0790

RW

kvarh Import of T3

INT32

kvarh

0792

RW

kvarh Export of T3

INT32

0794

RW

kVAh of T3

INT32

kVAh

0796

RW

kWh Import of T4

INT32

kWh

0798

RW

kWh Export of T4

INT32

0800

RW

kvarh Import of T4

INT32

kvarh

0802

RW

kvarh Export of T4

INT32

0804

RW

kVAh of T4

INT32

kVAh

0806

RW

kWh Import of T5

INT32

kWh

0808

RW

kWh Export of T5

INT32

0810

RW

kvarh Import of T5

INT32

kvarh

0812

RW

kvarh Export of T5

INT32

0814

RW

kVAh of T5

INT32

kVAh

0816

RW

kWh Import of T6

INT32

kWh

0818

RW

kWh Export of T6

INT32

0820

RW

kvarh Import of T6

INT32

kvarh

0822

RW

kvarh Export of T6

INT32

0824

RW

kVAh of T6

INT32

kVAh

0826

RW

kWh Import of T7

INT32

kWh

0828

RW

kWh Export of T7

INT32

0830

RW

kvarh Import of T7

INT32

kvarh

0832

RW

kvarh Export of T7

INT32

0834

RW

kVAh of T7

INT32

kVAh

0836

RW

kWh Import of T8

INT32

kWh

0838

RW

kWh Export of T8

INT32

0840

RW

kvarh Import of T8

INT32

kvarh

0842

RW

kvarh Export of T8

INT32

0844

RW

kVAh of T8

INT32

kVAh

Register

Property

Description

Format

Scale

Unit

0860

RW

kWh Import

INT32

x0.1

kWh

0862

RW

kWh Export

INT32

0864

RO

kWh Net

INT32

0866

RO

kWh Total

INT32

0868

RW

kvarh Import

INT32

kvarh

0870

RW

kvarh Export

INT32

0872

RO

kvarh Net

INT32

0874

RO

kvarh Total

INT32

0876

RW

kVAh

INT32

kVAh

0878

RW

kvarh Q1

INT32

kvarh

0880

RW

kvarh Q2

INT32

0882

RW

kvarh Q3

INT32

0884

RW

kvarh Q4

INT32

0886

RW

kWh Import of T1

INT32

kWh

0888

RW

kWh Export of T1

INT32

0890

RW

kvarh Import of T1

INT32

kvarh

0892

RW

kvarh Export of T1

INT32

0894

RW

kVAh of T1

INT32

kVAh

0896

RW

kWh Import of T2

INT32

kWh

0898

RW

kWh Export of T2

INT32

0900

RW

kvarh Import of T2

INT32

kvar

0902

RW

kvarh Export of T2

INT32

0904

RW

kVAh of T2

INT32

kVAh

0906

RW

kWh Import of T3

INT32

kWh

0908

RW

kWh Export of T3

INT32

0910

RW

kvarh Import of T3

INT32

kvarh

Table 5-6 Phase B Energy Measurements

5.2.4 Phase C (L3) Energy Measurements

54

CET Electric Technology

0912

RW

kvarh Export of T3

INT32

0914

RW

kVAh of T3

INT32

kVAh

0916

RW

kWh Import of T4

INT32

kWh

0918

RW

kWh Export of T4

INT32

0920

RW

kvarh Import of T4

INT32

kvarh

0922

RW

kvarh Export of T4

INT32

0924

RW

kVAh of T4

INT32

kVAh

0926

RW

kWh Import of T5

INT32

kWh

0928

RW

kWh Export of T5

INT32

0930

RW

kvarh Import of T5

INT32

kvarh

0932

RW

kvarh Export of T5

INT32

0934

RW

kVAh of T5

INT32

kVAh

0936

RW

kWh Import of T6

INT32

kWh

0938

RW

kWh Export of T6

INT32

0940

RW

kvarh Import of T6

INT32

kvarh

0942

RW

kvarh Export of T6

INT32

0944

RW

kVAh of T6

INT32

kVAh

0946

RW

kWh Import of T7

INT32

kWh

0948

RW

kWh Export of T7

INT32

0950

RW

kvarh Import of T7

INT32

kvarh

0952

RW

kvarh Export of T7

INT32

0954

RW

kVAh of T7

INT32

kVAh

0956

RW

kWh Import of T8

INT32

kWh

0958

RW

kWh Export of T8

INT32

0960

RW

kvarh Import of T8

INT32

kvarh

0962

RW

kvarh Export of T8

INT32

0964

RW

kVAh of T8

INT32

kVAh

Register

Property

Description

Format

Scale

Unit

1100

RW

kWh Import

INT32

x0.1

kWh

1102

RW

kWh Export

INT32

1104

RW

kvarh Import

INT32

kvarh

1106

RW

kvarh Export

INT32

1108

RW

kVAh

INT32

kVAh

Register

Property

Description

Format

Range/Unit

1200

RW

DI1 Pulse Counter

UINT32

0 to 1,000,000,000

DI Pulse Counter= Pulse Counter

x DI Pulse Weight

1202

RW

DI2 Pulse Counter

UINT32

1204

RW

DI3 Pulse Counter

UINT32

1206

RW

DI4 Pulse Counter

UINT32

1208

RW

DI5 Pulse Counter

UINT32

1210

RW

DI6 Pulse Counter

UINT32

Register

Property

Description

Format

Scale

Unit

1300

RO

Ia TDD

Float

x1

%

(0.1 means

10%)

1302

RO

Ib TDD

Float

1304

RO

Ic TDD

Float

1306

RO

Ia TDD Odd

Float

1308

RO

Ib TDD Odd

Float

1310

RO

Ic TDD Odd

Float

1312

RO

Ia TDD Even

Float

1314

RO

Ib TDD Even

Float

Table 5-7 Phase C Energy Measurements

5.2.5 Interval Energy Measurements

The Interval Energy registers have been added to the Modbus Map in Firmware V1.00.03 or later.

Table 5-8 Interval Energy Measurements

5.3 DI Pulse Counters

Table 5-9 DI Pulse Counter

5.4 Harmonic Measurements

5.4.1 Power Quality Measurements

55

CET Electric Technology

1316

RO

Ic TDD Even

Float

1318

RO

Ia K-factor

Float

-

1320

RO

Ib K-factor

Float

1322

RO

Ic K-factor

Float

1324

RO

Ia Crest-factor

Float

1326

RO

Ib Crest-factor

Float

1328

RO

Ic Crest-factor

Float

1330

RO

Voltage Unbalance

Float

1332

RO

Current Unbalance

Float

Register

Property

Description

Format

Scale

Unit

1400

RO

Ia THD

Float

x1

%

(0.1 means 10%)

1402

RO

Ib THD

Float

1404

RO

Ic THD

Float

1406

RO

Ia TOHD

Float

1408

RO

Ib TOHD

Float

1410

RO

Ic TOHD

Float

1412

RO

Ia TEHD

Float

1414

RO

Ib TEHD

Float

1416

RO

Ic TEHD

Float

1418

RO

Ia HD02

Float

1420

RO

Ib HD02

Float

1422

RO

Ic HD02

Float

1424~1590

RO

…

Float

1592

RO

Ia HD31

Float

1594

RO

Ib HD31

Float

1596

RO

Ic HD31

Float

Register

Property

Description

Format

Scale

Unit

1600

RO

Uan/Uab THD

Float

x1

%

(0.1 means 10%)

1602

RO

Ubn/Ubc THD

Float

1604

RO

Ucn/Uca THD

Float

1606

RO

Uan/Uab TOHD

Float

1608

RO

Ubn/Ubc TOHD

Float

1610

RO

Ucn/Uca TOHD

Float

1612

RO

Uan/Uab TEHD

Float

1614

RO

Ubn/Ubc TEHD

Float

1616

RO

Ucn/Uca TEHD

Float

1618

RO

Uan/Uab HD02

Float

1620

RO

Ubn/Ubc HD02

Float

1622

RO

Ucn/Uca HD02

Float

1624~1790

RO

…

Float

1792

RO

Uan/Uab HD31

Float

1794

RO

Ubn/Ubc HD31

Float

1796

RO

Ucn/Uca HD31

Float

Table 5-10 Power Quality Measurements

5.4.2 Current Harmonic Measurements

Table 5-11 Current Harmonic Measurements

5.4.3 Voltage Harmonic Measurements

Table 5-12 Voltage Harmonic Measurements

Notes:

1) When the Wiring Mode is 3P3W or 1P2W L-L, the phase A/B/C Voltage THD/TOHD/TEHD/HDxx

mean phase AB/BC/CA Voltage THD/TOHD/TEHD/HDxx.

2) When the Wiring Mode is 1P2W L-N or 1P2W L-L, the L2 and L3 phase voltages

THD/TOHD/TEHD/HDxx have no meaning, and their registers are reserved. When the Wiring Mode is 1P3W L-N, the L3 phase voltages THD/TOHD/TEHD/HDxx have no meaning, and their registers are reserved.

5.5 Demands

56

CET Electric Technology

Register

Property

Description

Format

Scale

Unit

3000

RO

Ia

Float

x1

A

3002

RO

Ib

Float

3004

RO

Ic

Float

3006

RO

kW Total

Float

x1 W 3008

RO

kvar Total

Float

x1

var

3010

RO

kVA Total

Float

x1

VA

Register

Property

Description

Format

Scale

Unit

3200

RO

Ia

Float

x1

A

3202

RO

Ib

Float

3204

RO

Ic

Float

3206

RO

kW Total

Float

x1

W

3208

RO

kvar Total

Float

x1

var

3210

RO

kVA Total

Float

x1

VA

Register

Property

Description

Format

Scale

Unit

3400~3405

RO

Ia

See

Section 5.5.5

Demand Data

Structure

x1

A

3406~3411

RO

Ib

3412~3417

RO

Ic

3418~3423

RO

kW Total

W

3424~3429

RO

kvar Total

var

3430~3435

RO

kVA Total

VA

3436~3441

RO

kW Total of T1

W

3442~3447

RO

kvar Total of T1

var

3448~3453

RO

kVA Total of T1

VA

3454~3459

RO

kW Total of T2

W

3460~3465

RO

kvar Total of T2

var

3466~3471

RO

kVA Total of T2

VA

3472~3477

RO

kW Total of T3

W

3478~3483

RO

kvar Total of T3

var

3484~3489

RO

kVA Total of T3

VA

3490~3495

RO

kW Total of T4

W

3496~3501

RO

kvar Total of T4

var

3502~3507

RO

kVA Total of T4

VA

3508~3513

RO

kW Total of T5

W

3514~3519

RO

kvar Total of T5

var

3520~3525

RO

kVA Total of T5

VA

3526~3531

RO

kW Total of T6

W

3532~3537

RO

kvar Total of T6

var

3538~3543

RO

kVA Total of T6

VA

3544~3549

RO

kW Total of T7

W

3550~3555

RO

kvar Total of T7

var

3556~3561

RO

kVA Total of T7

VA

3562~3567

RO

kW Total of T8

W

3568~3573

RO

kvar Total of T8

var

3574~3579

RO

kVA Total of T8

VA

Register

Property

Description

Format

Scale

Unit

3600~3605

RO

Ia

See

Section 5.5.5

Demand Data

Structure

x1

A

3606~3611

RO

Ib

3612~3617

RO

Ic

3618~3623

RO

kW Total

W

3624~3629

RO

kvar Total

var

5.5.1 Present Demands

Table 5-13 Present Demand Measurements

5.5.2 Predicted Demands

Table 5-14 Predicted Demand Measurements

5.5.3 Peak Demand Log of This Month (Since Last Reset)

Table 5-15 Peak Demand Log of This Month (Since Last Reset)

5.5.4 Peak Demand Log of Last Month (Before Last Reset)

57

CET Electric Technology

3630~3635

RO

kVA Total

VA

3636~3641

RO

kW Total of T1

W

3642~3647

RO

kvar Total of T1

var

3648~3653

RO

kVA Total of T1

VA

3654~3659

RO

kW Total of T2

W

3660~3665

RO

kvar Total of T2

var

3666~3671

RO

kVA Total of T2

VA

3672~3677

RO

kW Total of T3

W

3678~3683

RO

kvar Total of T3

var

3684~3689

RO

kVA Total of T3

VA

3690~3695

RO

kW Total of T4

W

3696~3701

RO

kvar Total of T4

var

3702~3707

RO

kVA Total of T4

VA

3708~3713

RO

kW Total of T5

W

3714~3719

RO

kvar Total of T5

var

3720~3725

RO

kVA Total of T5

VA

3726~3731

RO

kW Total of T6

W

3732~3737

RO

kvar Total of T6

var

3738~3743

RO

kVA Total of T6

VA

3744~3749

RO

kW Total of T7

W

3750~3755

RO

kvar Total of T7

var

3756~3761

RO

kVA Total of T7

VA

3762~3767

RO

kW Total of T8

W

3768~3773

RO

kvar Total of T8

var

3774~3779

RO

kVA Total of T8

VA

Offset

Description

+0

High

Year - 2000

Low

Month

+1

High

Day

Low

Hour

+2

High

Minute

Low

Second

+3

-

Millisecond

+4~+5

-

Peak Demand Value

Register

Property

Description

Format

Scale

Unit

4000~4005

RO

Uan

See 5.6.5

Max./Min. Log

Structure

x1

V

4006~4011

RO

Ubn

4012~4017

RO

Ucn

4018~4023

RO

Uln Average

4024~4029

RO

Uab

4030~4035

RO

Ubc

4036~4041

RO

Uca

4042~4047

RO

Ull Average

4048~4053

RO

Ia

x1

A

4054~4059

RO

Ib

4060~4065

RO

Ic

4066~4071

RO

I Average

4072~4077

RO

kWa

x1

W

4078~4083

RO

kWb

4084~4089

RO

kWc

4090~4095

RO

kW Total

4096~4101

RO

kvara

x1

var

4102~4107

RO

kvarb

4108~4113

RO

kvarc

4114~4119

RO

kvar Total

Table 5-16 Peak Demand Log of Last Month (Before Last Reset)

5.5.5 Demand Data Structure

Table 5-17 Demand Data Structure

5.6 Max./Min. Log

5.6.1 Max. Log of This Month (Since Last Reset)

58

CET Electric Technology

4120~4125

RO

kVAa

x1

VA

4126~4131

RO

kVAb

4132~4137

RO

kVAc

4138~4143

RO

kVA Total

4144~4149

RO

PFa

x1

-

4150~4155

RO

PFb

4156~4161

RO

PFc

4162~4167

RO

PF Total

4168~4173

RO

Frequency

x1

Hz

4174~4179

RO

In (Calculated)

x1

A

4180~4185

RO

Uan/Uab THD

x1

-

4186~4191

RO

Ubn/Ubc THD

4192~4197

RO

Ucn/Uca THD

4198~4203

RO

Ia THD

4204~4209

RO

Ib THD

4210~4215

RO

Ic THD

4216~4221

RO

Ia K-factor

4222~4227

RO

Ib K-factor

4228~4233

RO

Ic K-factor

4234~4239

RO

Ia Crest-factor

4240~4245

RO

Ib Crest-factor

4246~4251

RO

Ic Crest-factor

4252~4257

RO

Voltage Unbalance

4258~4263

RO

Current Unbalance

4264~4269

RO

I4

x1

A

4270~4275

RO

Ir* (Residual Current)

Register

Property

Description

Format

Scale

Unit

4300~4305

RO

Uan

See 5.6.5

Max./Min. Log

Structure

x1

V

4306~4311

RO

Ubn

4312~4317

RO

Ucn

4318~4323

RO

Uln Average

4324~4329

RO

Uab

4330~4335

RO

Ubc

4336~4341

RO

Uca

4342~4347

RO

Ull Average

4348~4353

RO

Ia

x1

A

4354~4359

RO

Ib

4360~4365

RO

Ic

4366~4371

RO

I Average

4372~4377

RO

kWa

x1

W

4378~4383

RO

kWb

4384~4389

RO

kWc

4390~4395

RO

kW Total

4396~4401

RO

kvara

x1

var

4402~4407

RO

kvarb

4408~4413

RO

kvarc

4414~4419

RO

kvar Total

4420~4425

RO

kVAa

x1

VA

4426~4431

RO

kVAb

4432~4437

RO

kVAc

4438~4443

RO

kVA Total

4444~4449

RO

PFa

x1

-

4450~4455

RO

PFb

4456~4461

RO

PFc

4462~4467

RO

PF Total

4468~4473

RO

Frequency

x1

Hz

4474~4479

RO

In (Calculated)

x1

A

4480~4485

RO

Uan/Uab THD

x1

-

4486~4491

RO

Ubn/Ubc THD

4492~4497

RO

Ucn/Uca THD

4498~4503

RO

Ia THD

#

Available in Firmware V1.00.06 or later

Table 5-18 Max. Log of This Month (Since Last Reset)

5.6.2 Min. Log of This Month (Since Last Reset)

59

CET Electric Technology

4504~4509

RO

Ib THD

4510~4515

RO

Ic THD

4516~4521

RO

Ia K-factor

4522~4527

RO

Ib K-factor

4528~4533

RO

Ic K-factor

4534~4539

RO

Ia Crest-factor

4540~4545

RO

Ib Crest-factor

4546~4551

RO

Ic Crest-factor

4552~4557

RO

Voltage Unbalance

4558~4563

RO

Current Unbalance

4564~4569

RO

I4

x1

A

4570~4575

RO

Ir* (Residual Current)

Register

Property

Description

Format

Scale

Unit

4600~4605

RO

Uan

See 5.6.5

Max./Min. Log

Structure

x1

V

4606~4611

RO

Ubn

4612~4617

RO

Ucn

4618~4623

RO

Uln Average

4624~4629

RO

Uab

4630~4635

RO

Ubc

4636~4641

RO

Uca

4642~4647

RO

Ull Average

4648~4653

RO

Ia

x1

A

4654~4659

RO

Ib

4660~4665

RO

Ic

4666~4671

RO

I Average

4672~4677

RO

kWa

x1

W

4678~4683

RO

kWb

4684~4689

RO

kWc

4690~4695

RO

kW Total

4696~4701

RO

kvara

x1

var

4702~4707

RO

kvarb

4708~4713

RO

kvarc

4714~4719

RO

kvar Total

4720~4725

RO

kVAa

x1

VA

4726~4731

RO

kVAb

4732~4737

RO

kVAc

4738~4743

RO

kVA Total

4744~4749

RO

PFa

x1

-

4750~4755

RO

PFb

4756~4761

RO

PFc

4762~4767

RO

PF Total

4768~4773

RO

Frequency

x1

Hz

4774~4779

RO

In (Calculated)

x1

-

4780~4785

RO

Uan/Uab THD

4786~4791

RO

Ubn/Ubc THD

4792~4797

RO

Ucn/Uca THD

4798~4803

RO

Ia THD

4804~4809

RO

Ib THD

4810~4815

RO

Ic THD

4816~4821

RO

Ia K-factor

4822~4827

RO

Ib K-factor

4828~4833

RO

Ic K-factor

4834~4839

RO

Ia Crest-factor

4840~4845

RO

Ib Crest-factor

4846~4851

RO

Ic Crest-factor

4852~4857

RO

Voltage Unbalance

4858~4863

RO

Current Unbalance

4864~4869

RO

I4

x1

A

4870~4875

RO

Ir* (Residual Current)

#

Available in Firmware V1.00.06 or later

Table 5-19 Min. Log of This Month (Since Last Reset)

5.6.3 Max. Log of Last Month (Before Last Reset)

#

Available in Firmware V1.00.06 or later

Table 5-20 Max. Log of Last Month (Before Last Reset)

60

CET Electric Technology

Register

Property

Description

Format

Scale

Unit

4900~4905

RO

Uan

See 5.6.5

Max./Min. Log

Structure

x1

V

4906~4911

RO

Ubn

4912~4917

RO

Ucn

4918~4923

RO

Uln Average

4924~4929

RO

Uab

4930~4935

RO

Ubc

4936~4941

RO

Uca

4942~4947

RO

Ull Average

4948~4953

RO

Ia

x1

A

4954~4959

RO

Ib

4960~4965

RO

Ic

4966~4971

RO

I Average

4972~4977

RO

kWa

x1

W

4978~4983

RO

kWb

4984~4989

RO

kWc

4990~4995

RO

kW Total

4996~5001

RO

kvara

x1

var

5002~5007

RO

kvarb

5008~5013

RO

kvarc

5014~5019

RO

kvar Total

5020~5025

RO

kVAa

x1

VA

5026~5031

RO

kVAb

5032~5037

RO

kVAc

5038~5043

RO

kVA Total

5044~5049

RO

PFa

x1

-

5050~5055

RO

PFb

5056~5061

RO

PFc

5062~5067

RO

PF Total

5068~5073

RO

Frequency

x1

Hz

5074~5079

RO

In (Calculated)

x1

A

5080~5085

RO

Uan/Uab THD

x1

-

5086~5091

RO

Ubn/Ubc THD

5092~5097

RO

Ucn/Uca THD

5098~5103

RO

Ia THD

5104~5109

RO

Ib THD

5110~5115

RO

Ic THD

5116~5121

RO

Ia K-factor

5122~5127

RO

Ib K-factor

5128~5133

RO

Ic K-factor

5134~5139

RO

Ia Crest-factor

5140~5145

RO

Ib Crest-factor

5146~5151

RO

Ic Crest-factor

5152~5157

RO

Voltage Unbalance

5158~5163

RO

Current Unbalance

5164~5169

RO

I4

x1

A

5170~5175

RO

Ir* (Residual Current)

Offset

Description

+0

High

Year - 2000

Low

Month

+1

High

Day

Low

Hour

+2

High

Minute

Low

Second

+3

-

Millisecond

+4~+5

-

Max./Min. Value

5.6.4 Min. Log of Last Month (Before Last Reset)

#

Available in Firmware V1.00.06 or later

Table 5-21 Min. Log of Last Month (Before Last Reset)

5.6.5 Max./Min. Log Structure

Table 5-22 Max./Min. Structure

61

5.7 Monthly Energy Log

Register

Property

Description

Format

Scale

Unit

0980

RW

Month1

INT16

0* to 12

0981

RO

High-order Byte: Year (0-99)

Low-order Byte: Month (1-12)

INT16

Time Stamp

(20YY/MM/DD

HH:MM:SS)

0982

RO

High-order Byte: Day (1-31)

Low-order Byte: Hour (0-23)

INT16

0983

RO

High-order Byte: Minute (0-59)

Low-order Byte: Second (0-59)

INT16

0984

RW

kWh Import

INT32

x0.1

kWh

0986

RW

kWh Export

INT32

0988

RO

kWh Net

INT32

0990

RO

kWh Total

INT32

0992

RW

kvarh Import

INT32

x0.1

kvarh

0994

RW

kvarh Export

INT32

0996

RO

kvarh Net

INT32

0998

RO

kvarh Total

INT32

1000

RW

kVAh

INT32

x0.1

kVAh

1002

RW

kvarh Q1

INT32

x0.1

kvarh

1004

RW

kvarh Q2

INT32

1006

RW

kvarh Q3

INT32

1008

RW

kvarh Q4

INT32

1010

RW

kWh Import of T1

INT32

x0.1

kWh

1012

RW

kWh Export of T1

INT32

1014

RW

kvarh Import of T1

INT32

x0.1

kvarh

1016

RW

kvarh Export of T1

INT32

1018

RW

kVAh of T1

INT32

x0.1

kVAh

1020

RW

kWh Import of T2

INT32

x0.1

kWh

1022

RW

kWh Export of T2

INT32

1024

RW

kvarh Import of T2

INT32

x0.1

kvarh

1026

RW

kvarh Export of T2

INT32

1028

RW

kVAh of T2

INT32

x0.1

kVAh

1030

RW

kWh Import of T3

INT32

x0.1

kWh

1032

RW

kWh Export of T3

INT32

1034

RW

kvarh Import of T3

INT32

x0.1

kvarh

1036

RW

kvarh Export of T3

INT32

1038

RW

kVAh of T3

INT32

x0.1

kVAh

1040

RW

kWh Import of T4

INT32

x0.1

kWh

1042

RW

kWh Export of T4

INT32

1044

RW

kvarh Import of T4

INT32

x0.1

kvarh

1046

RW

kvarh Export of T4

INT32

1048

RW

kVAh of T4

INT32

x0.1

kVAh

1050

RW

kWh Import of T5

INT32

x0.1

kWh

1052

RW

kWh Export of T5

INT32

1054

RW

kvarh Import of T5

INT32

x0.1

kvarh

1056

RW

kvarh Export of T5

INT32

1058

RW

kVAh of T5

INT32

x0.1

kVAh

1060

RW

kWh Import of T6

INT32

x0.1

kWh

1062

RW

kWh Export of T6

INT32

1064

RW

kvarh Import of T6

INT32

x0.1

kvarh

1066

RW

kvarh Export of T6

INT32

1068

RW

kVAh of T6

INT32

x0.1

kVAh

1070

RW

kWh Import of T7

INT32

x0.1

kWh

1072

RW

kWh Export of T7

INT32

1074

RW

kvarh Import of T7

INT32

x0.1

kvarh

1076

RW

kvarh Export of T7

INT32

1078

RW

kVAh of T7

INT32

x0.1

kVAh

1080

RW

kWh Import of T8

INT32

x0.1

kWh

1082

RW

kWh Export of T8

INT32

1084

RW

kvarh Import of T8

INT32

x0.1

kvarh

1086

RW

kvarh Export of T8

INT32

1088

RW

kVAh of T8

INT32

x0.1

kVAh

CET Electric Technology

Table 5-23 Monthly Energy Log

62

CET Electric Technology

Register

Property

Description

Format

Scale

Unit

12000

RW

Index1

INT16

1 to 60

12001

RO

High-order Byte: Year (0-99)

Low-order Byte: Month (1-12)

INT16

-

12002

RO

High-order Byte: Day (1-31)

Low-order Byte: Hour (0-23)

INT16

12003

RO

High-order Byte: Minute (0-59)

Low-order Byte: Second (0-59)

INT16

12004

RO

kWh Total

INT32

x0.1

kWh

12006

RO

kvarh Total

INT32

x0.1

kvarh

12008

RO

kVAh Total

INT32

x0.1

kVAh

12010

RO

Peak Demand of kW Total

Float

x1

W

12012

RO

Peak Demand of kvar Total

Float

x1

var

12014

RO

Peak Demand of kVA Total

Float

x1

VA

Register

Property

Description

Format

Scale

Unit

12500

RW

Index1

INT16

1 to 36

12501

RO

High-order Byte: Year (0-99)

Low-order Byte: Month (1-12)

INT16

-

12502

RO

High-order Byte: Day (1-31)

Low-order Byte: Hour (0-23)

INT16

12503

RO

High-order Byte: Minute (0-59)

Low-order Byte: Second (0-59)

INT16

12504

RO

kWh Total

INT32

x0.1

kWh

12506

RO

kvarh Total

INT32

x0.1

kvarh

12508

RO

kVAh Total

INT32

x0.1

kVAh

12510~12515

RO

Peak Demand of kW Total

See Table 5-26

Demand Data Structure

12516~12521

RO

Peak Demand of kvar Total

12522~12527

RO

Peak Demand of kVA Total

Offset

Description

+0

High

Year - 2000

Low

Month

+1

High

Day

Notes:

1) This register represents the Month when it is read. To read the Monthly Energy Log, this register

must be first written to indicate to the PMC-53A which log to load from memory. The range of this register is from 0 to 12, which represents the Present Month and the Last 12 Months. For example, if the current month is 2016/10, “0” means 2016/10, “1” means 2016/09, “2” means 2016/08, … and ”12” means “2015/10”.

2) For each Monthly Energy Log, the time stamp shows the exact Self-Read Time (20YY/MM/DD

HH:MM:SS) when the log was recorded. For the Monthly Energy Log of the Present Month, the time stamp shows the current time of the meter because the Present Month is not yet over.

3) The Monthly Energy Log for the Present Month can be modified, but the Monthly Energy Logs

for the Last 12 Months are Read Only.

5.8 Daily and Monthly Freeze Logs (Optional)

5.8.1 Daily Freeze Log

Table 5-24 Daily Freeze Log

Notes:

1) There is no Log Pointer that indicates the current logging position. Writing a value N between 1

and 60 to the Index register to retrieve the Daily Freeze Log of the Nth entry. For example, writing 1 to the Index register will retrieve yesterday’s Daily Freeze Log. If N = 0 or N > 60, an exception response will be returned with the Illegal Data Value error code (0x03) as defined by the Modbus protocol. If all the returned values of the Nth Log Record (where 1 ≤ N ≤ 60) are all 0 (including the timestamp), this indicates that the returned Log Record is invalid and that the end of the Log has been reached. If the software is reading the Log for the very first time, it should start with N=1 and stop when either N=60 or when the returned Log Record is invalid. After that, all the software has to do is to read the Log on a daily basis with N=1.

5.8.2 Monthly Freeze Log

Table 5-25 Monthly Freeze Log

63

CET Electric Technology

Low

Hour

+2

High

Minute

Low

Second

+3

-

Millisecond

+4~+5

-

Peak Demand Value

Register

Property

Description

Format

10000~10007

RO

Event 1

See Table 5-28

SOE Log Data

Structure

10008~10015

RO

Event 2

10016~10023

RO

Event 3

10024~10031

RO

Event 4

10032~10039

RO

Event 5

10040~10047

RO

Event 6

10048~10055

RO

Event 7

10056~10063

RO

Event 8

10064~10071

RO

Event 9

10072~10079

RO

Event 10

10080~10087

RO

Event 11

10088~10095

RO

Event 12

…

10792~10799

RO

Event 100

Offset

Property

Description

Unit

+0

RO

High-order Byte: Event Classification

See Table 5-29

SOE Classification

RO

Low-order Byte: Sub-Classification

+1

RO

Record Time: Year

0-99 (Year-2000)

RO

Record Time: Month

1 to 12

+2

RO

Record Time: Day

1 to 31

RO

Record Time: Hour

0 to 23

+3

RO

Record Time: Minute

0 to 59

RO

Record Time: Second

0 to 59

+4

RO

Record Time: Millisecond

0 to 999

+5

RO

High-order Byte: Reserved

-

RO

Low-order Byte: Status2

-

+6 to +7

RO

Event Value2

-

Table 5-26 Demand Data Structure

Notes:

1) There is no Log Pointer that indicates the current logging position. Writing a value N between 1

and 36 to the Index register to retrieve the Monthly Freeze Log of the Nth entry. For example, writing 1 to the Index register will retrieve last month’s Monthly Freeze Log. If N = 0 or N > 36, an exception response will be returned with the Illegal Data Value error code (0x03) as defined by the Modbus protocol. If all the returned values of the Nth Log Record (where 1 ≤ N ≤ 36) are all 0 (including the timestamp), this indicates that the returned Log Record is invalid and that the end of the Log has been reached. If the software is reading the Log for the very first time, it should start with N=1 and stop when either N=36 or when the returned Log Record is invalid. After that, all the software has to do is to read the Log on a monthly basis with N=1.

5.9 SOE Log

The SOE Log Pointer points to the register address within the SOE Log where the next event will be stored. The following formula is used to determine the register address of the most recent SOE event referenced by the SOE Log Pointer value:

Register Address = 10000 + Modulo(SOE Log Pointer-1/100)*8

Table 5-27 SOE Log

Notes: SOE Log Data Structure

Table 5-28 SOE Log Data Structure

64

SOE Classification

Event

Classification

Sub-

Classification

Status

Event Value

Description

1=DI Changes

1

1 / 0 DI1 Inactive / DI1 Active

2

1 / 0 DI2 Inactive / DI2 Active

3

1 / 0 DI3 Inactive / DI3 Active

4

1 / 0 DI4 Inactive / DI4 Active

5

1 / 0 DI5 Inactive / DI5 Active

6

1 / 0 DI6 Inactive / DI6 Active

2=DO Changes

1

1 / 0

DO1 Operated/Released

by Remote Control

2

1 / 0

DO2 Operated/Released

by Remote Control

3

1 / 0

DO3 Operated/Released

by Remote Control

4

1 / 0

DO4 Operated/Released

by Remote Control

5~10

Reserved

11

1 / 0 DO1 Operated/Released by Setpoint

12

1 / 0 DO2 Operated/Released by Setpoint

13

1 / 0 DO3 Operated/Released by Setpoint

14

1 / 0 DO4 Operated/Released by Setpoint

15~20

Reserved

21

1 / 0

DO1 Operated/Released by Front Panel

22

1 / 0

DO2 Operated/Released by Front Panel

23

1 / 0

DO3 Operated/Released by Front Panel

24

1 / 0

DO4 Operated/Released by Front Panel

25~30

Reserved

31 0

DO1 Released when Pulse Time out

32 0

DO2 Released when Pulse Time out

33 0

DO3 Released when Pulse Time out

34 0

DO4 Released when Pulse Time out

3=Setpoint

1

1 / 0

Trigger Value / Return

Value

Over Uln Setpoint Active/Return

2

1 / 0

Over Ull Setpoint Active/Return

3

1 / 0

Over Current Setpoint Active/Return

4

1 / 0

Over In Setpoint Active/Return

5

1 / 0

Over Frequency Setpoint Active/Return

6

1 / 0

Over kW Total Setpoint Active/Return

7

1 / 0

Over kvar Total Setpoint Active/Return

8

1 / 0

Over kVA Total Setpoint Active/Return

9

1 / 0

Over PF Total Setpoint Active/Return

10

1 / 0

Over kW Total Present Demand Setpoint

Active/Return

11

1 / 0

Over kvar Total Present Demand

Setpoint Active/Return

12

1 / 0

Over kVA Total Present Demand Setpoint

Active/Return

13

1 / 0

Over kW Total Predicted Demand

Setpoint Active/Return

14

1 / 0

Over kvar Total Predicted Demand

Setpoint Active/Return

15

1 / 0

Over kVA Total Predicted Demand

Setpoint Active/Return

16

1 / 0

Over Voltage THD Setpoint Active/Return

17

1 / 0

Over Voltage TOHD Setpoint

Active/Return

18

1 / 0

Over Voltage TEHD Setpoint

Active/Return

19

1 / 0

Over Current THD Setpoint

Active/Return

20

1 / 0

Over Current TOHD Setpoint

Active/Return

21

1 / 0

Over Current TEHD Setpoint

Active/Return

22

1 / 0

Over Voltage Unbalance Setpoint

Active/Return

CET Electric Technology

65

CET Electric Technology

23

1 / 0

Over Current Unbalance Setpoint

Active/Return

24

1 / 0

Reversal Phase Setpoint Active/Return

25

1 / 0

Over I4 Setpoint Active/Return

26

1 / 0

Over AI Setpoint Active/Return

27

Reserved

28

1 / 0

Over Temprature1 Setpoint

Active/Return

29

1 / 0

Over Temprature2 Setpoint

Active/Return

30

1 / 0

RTD 1 Broken

31

1 / 0

RTD 2 Broken

32

1 / 0

Over Ir (Residual Current) Setpoint*

Active/Return

33

1 / 0

Over U2 (Negative Sequence) Setpoint*

Active/Return

34

1 / 0

Over U0 (Zero Sequence) Setpoint*

Active/Return

35~40

Reserved

41

1 / 0

Under Uln Setpoint Active/Return

42

1 / 0

Under Ull Setpoint Active/Return

43

1 / 0

Under Current Setpoint Active/Return

44

1 / 0

Under In Setpoint Active/Return

45

1 / 0

Under Frequency Setpoint Active/Return

46

1 / 0

Under kW Total Setpoint Active/Return

47

1 / 0

Under kvar Total Setpoint Active/Return

48

1 / 0

Under kVA Total Setpoint Active/Return

49

1 / 0

Under PF Total Setpoint Active/Return

50

1 / 0

Under kW Total Present Demand

Setpoint Active/Return

51

1 / 0

Under kvar Total Present Demand

Setpoint Active/Return

52

1 / 0

Under kVA Total Present Demand

Setpoint Active/Return

53

1 / 0

Under kW Total Predicted Demand

Setpoint Active/Return

54

1 / 0

Under kvar Total Predicted Demand

Setpoint Active/Return

55

1 / 0

Under kVA Total Predicted Demand

Setpoint Active/Return

56

1 / 0

Under Voltage THD Setpoint

Active/Return

57

1 / 0

Under Voltage TOHD Setpoint

Active/Return

58

1 / 0

Under Voltage TEHD Setpoint

Active/Return

59

1 / 0

Under Current THD Setpoint

Active/Return

60

1 / 0

Under Current TOHD Setpoint

Active/Return

61

1 / 0

Under Current TEHD Setpoint

Active/Return

62

1 / 0

Under Voltage Unbalance Setpoint

Active/Return

63

1 / 0

Under Current Unbalance Setpoint

Active/Return

64

1 / 0

Under I4 Setpoint Active/Return

65

1 / 0

Under AI Setpoint Active/Return

66

Reserved

67

1 / 0

Under Temprature1 Setpoint

Active/Return

68

1 / 0

Under Temprature2 Setpoint

Active/Return

69

1 / 0

Under Ir (Residual Current) Setpoint*

Active/Return

70

1 / 0

Under U2 (Negative Sequence) Setpoint*

Active/Return

66

CET Electric Technology

71

1 / 0

Under U0 (Zero Sequence) Setpoint*

Active/Return

4=Self-

diagnosis

1 1 0

System Parameter Fault

2 1 0

Internal Parameter Fault

3 1 0

TOU Parameter Fault

4 1 0

Memory Fault

5=Operations

1 0 0

Power On

2 0 0

Power Off

3 0 0

Clear Present Energy via Front Panel

1

4 0 0

Clear Historical Monthly Energy Log via

Front Panel

2

5 0 0

Clear Peak Demand Log of This Month

(Since Last Reset) via the Front Panel

6 0 0

Clear Present Demand, Peak Demand

Log of This Month (Since Last Reset) and

Last Month (Before Last Reset) via the

Front Panel

7 0 0

Clear Present Max./Min. via Front Panel

8 0 0

Clear All Max./Min. via Front Panel

9 0 0

Clear All Data via Front Panel

3

10 0 0

Clear SOE Log via Front Panel

11

0

x=1 to 6

Clear DIx Pulse Counter via Front Panel

12 0 0

Clear All Pulse Counter via Front Panel

13 0 0

Clear Device Operating Time via Front

Panel

14 0 0

Set Clock via Front Panel

15 0 0

Setup Changed via Front Panel

16~17 0 …

Reserved

18 0 0

Restore Factory Default via Front Panel

19~29 0 …

Reserved

30 0 0

Clear All Energy Registers via

Communications

4

31 0 0

Clear Present Monthly Energy Log via

Communications5

32 0 0

Clear Historical Monthly Energy Log via

Communications6

33 0 0

Clear Peak Demand of

This Month (Since Last Reset) via

Communications

34 0 0

Clear All Demand Registers via

Communications

35 0 0

Clear Max./Min. Logs of This Month

(Since Last Reset) via Communications

36 0 0

Clear All Max./Min. Logs via

Communications

37 0 0

Clear All Data via Communications

3

38 0 0

Clear SOE Log via Communications

39

0

x=1 to 6

Clear DIx Pulse Counter via

Communications

40 0 0

Clear All DI Pulse Counters via

Communications

41 0 0

Clear Device Operating Time via

Communications

42 0 0

Restore Factory Default via

Communications

43 0 0

Setup Changes via Communications

44 0 0

Preset Energy Value via Communications

45 0 0

Setup TOU Energy via Communications

46 0 1~4

Switch TOU Schedule7

47 0 1~5

Clear DRx Log via Communications

48 0 0

Clear All DR logs via Communications

#

Available in Firmware V1.00.06 or later

1) Clear Present Energy Log means to clear 3-Phase Total Energy registers, Phase A/B/C Energy

registers, Tariff Energy and Monthly Energy Log of the Present Month.

Table 5-29 SOE Event Classification

67

CET Electric Technology

Record Value

Description

1

Switch Schedule 1 to Schedule 2 manually

2

Switch Schedule 2 to Schedule 1 manually

3

Switch Schedule 1 to Schedule 2 automatically

4

Switch Schedule 2 to Schedule 1 automatically

Register

Property

Description

Format

20000~20037

RO

DR Log #1 Buffer

See Table 5-32

Standard DR Log Structure

20038~20075

RO

DR Log #2 Buffer

20076~20113

RO

DR Log #3 Buffer

20114~20151

RO

DR Log #4 Buffer

20152~20189

RO

DR Log #5 Buffer

Offset

Property

Description

Format

+0

RW

DR Log X Pointer

UINT32

+2

RO

High-order Byte: Year (0-99)

Low-order Byte: Month (1-12)

UINT16

+3

RO

High-order Byte: Day (1-31)

Low-order Byte: Hour (0-23)

UINT16

+4

RO

High-order Byte: Minute (0-59)

Low-order Byte: Second (0-59)

UINT16

+5

RO

Millisecond

UINT16

+6~+7

RO

Parameter #1

Float

+8~+9

RO

Parameter #2

+10~+11

Parameter #3

…

+36~+37

RO

Parameter #16

Register

Property

Description

Format

Range, Default*

6000

RW

PT Primary1

UINT32

1 to 1,000,000 V, 100*

6002

RW

PT Secondary

UINT32

1 to 690V, 100*

6004

RW

CT Primary

UINT32

1 to 30,000A, 5*

6006

RW

CT Secondary

UINT32

1 to 5A, 5*

6008~6010

RW

Reserved

UINT32

6012

RW

I4 Primary

UINT32

1 to 30,000A, 5*

6014

RW

I4 Secondary

UINT32

1 to 5A, 5*

6016~6018

RW

Reserved

UINT32

6020

RW

Wiring Mode

UINT16

0=DEMO, 1=1P2W L-N,

2) Clear Historical Monthly Energy Log means to clear the Monthly Energy Log of the last 1 to 12

months, excluding the Monthly Energy Log for the Present Month.

3) Clear All Data via Front Panel or Communication means to clear 3-Phase Total Energy registers,

Phase A/B/C Energy registers, Monthly Energy Log of the Present Month, All Peak Demands, All Max./Min. Logs, Device Operating Time, All DI Pulse Counters, All DR Logs and All Freeze Logs.

4) Clear All Energy Registers means to clear the 3-Ø Total and Per-Phase energy registers.

5) Clear Present Monthly Energy Log means to clear the Monthly Energy Log of the Present Month.

6) Clear Historical Monthly Energy Log means to clear Monthly Energy Log of the last 1 to 12 months,

excluding the Monthly Energy Log for the Present Month.

7) The event values of Switch TOU Schedule are illustrated in the table below:

Table 5-30 TOU Switch Records

5.10 Data Recorder Log (Optional)

Table 5-31 DR Log

Table 5-32 DR Data Buffer Structure

Notes:

1) Writing n to the DR Log X Pointer register will load the Log Record at pointer position n into the

DR Log X Buffer from the device’s memory.

2) Writing a pointer value that points to a Log Record that is either already expired or has not been

generated yet to the DR Log X Pointer register will generate an exception response with the Illegal Data Value error code (0x03) as defined by the Modbus protocol.

5.11 Device Setup

5.11.1 Basic Setup Parameters

68

CET Electric Technology

2=1P2W L-L, 3=1P3W

4=3P3W, 5=3P4W*

6021

RW

PF Convention

UINT16

0=IEC*, 1=IEEE, 2=-IEEE

6022

RW

kVA Calculation

UINT16

0=Vector*, 1=Scalar

6023

RW

Ia Polarity

UINT16

0=Normal*, 1=Reverse

6024

RW

Ib Polarity

UINT16

6025

RW

Ic Polarity

UINT16

6026~6027

RW

Reserved

UINT16 6028

RW

THD Calculation

2

UINT16

0= THDf*, 1= THDr

6029

RW

Demand Period

UINT16

1 to 60 (minutes), 15*

6030

RW

Number of Sliding Windows

UINT16

1 to 15, 1*

6031

RW

Predicted Response

UINT16

70 to 99, 70*

6032

RW

Arm before Execute

UINT16

0=Disabled*, 1=Enabled

6033

RW

Self-Read Time3

UINT16

0xFFFF*

6034

RW

Monthly Energy Log Self-Read

Time

4

UINT16

0*

6035

RW

Energy Pulse Constant

UINT16

0=1000 imp/kxh*

1=3200 imp/kxh

6036

RW

LED Energy Pulse

UINT16

0=Disabled

1=kWh* 2=kvarh

6037

RW

Backlight Time-out

UINT16

0 to 60 (mins), 5*

6038

RW

System Language

UINT16

1=English

6039

RW

Date Format

UINT16

0=YYMMDD*

1=MMDDYY 2=DDMMYY

6040

RW

Delimiter4

UINT16

0=Option 1*, 1=Option 2

See Note 4

6041

RW

Monthly Freeze

Self-Read Time5

UINT16

0*

6042

RW

Daily Freeze

Self-Read Time6

UINT16

0*

6043

RW

Default Display 1st parameter

7

UINT16

0 to 36, 7* (Ullavg)

6044

RW

Default Display 2nd parameter7

UINT16

0 to 36, 11* (Iavg)

6045

RW

Default Display 3rd parameter7

UINT16

0 to 36, 12* (P)

6046

RW

Default Display 4th parameter7

UINT16

0 to 36, 15* (PF)

6047

RW

EN Period8

UINT16

5 to 60* min

6048

RW

Setpoint LCD Flash Alarm~

UINT16

0=Enabled*, 1=Disabled

6049

RW

Current Threshold of

Device Operating Time~

UINT16

1* to 1000 (x0.001In)

6050

RW

kvarh Calculation~

UINT16

0=RMS*, 1=kvarh Fund.

6051

RW

DNP Polling Object~

9

UINT16

0 to 65535, 0x3F*

%100THD

1

2









I

n

%100THD

1

2













n

I

#

Available in Firmware V1.00.03 or later

~ Available in Firmware V1.00.06 or later

Notes:

1) The value of [PT Primary/PT Secondary] cannot exceed 10000.

2) There are two ways to calculate THD:

THDf (based on Fundamental):

where In represents the RMS value for the nth harmonic and I1 represents the RMS value of the Fundamental component.

THDr (based on RMS):

where In represents the RMS value for the nth harmonic.

Table 5-33 Basic Setup Parameters

69

CET Electric Technology

Key

Parameters

Key

Parameters

Key

Parameters

Key

Parameters

0

U1 (Uan)

10

I3 (Ic)

20

T1 kWh Imp

30

Fund. kW Total*

1

U2 (Ubn)

11

Iavg

21

T2 kWh Imp

31

dPF Total*

2

U3 (Ucn)

12

P (kW Total)

22

T3 kWh Imp

32

I4*

3

Ulnavg

13

Q (kvar Total)

23

T4 kWh Imp

33

U1 THD*

4

U12 (Uab)

14

S (kVA Total)

24

I1 (Ia) Demand

34

U2 THD*

5

U23 (Ubc)

15

PF (PF Total)

25

I2 (Ib) Demand

35

U3 THD*

6

U31 (Uca)

16

Frequency

26

I3 (Ic) Demand

36

Ir*

7

Ullavg

17

kWh Import

27

kW Demand

8

I1 (Ia)

18

kWh Export

28

kvar Demand*

9

I2 (Ib)

19

kWh Total

29

kVA Demand*

Bit

Object Description

Option

0

Object 1: Binary Inputs

0=Disabled

1=Enabled*

1

Object 10: Binary Output

2

Object 20: 32-Bit Binary Counters

3

Object 20: 16-Bit Binary Counters

4

Object 30: Analog Inputs Primary Readings

5

Object 40: Analog Output Status

6 to 15

Reserved

Register

Property

Description

Format

Range, Default*

6200

RW

DI1 Function

UINT16

0 = Digital Input* 1=Pulse Counting

2 =Tariff Switch1

6201

RW

DI2 Function

UINT16

6202

RW

DI3 Function

UINT16

6203

RW

DI4 Function

UINT16

6204

RW

DI5 Function

UINT16

6205

RW

DI6 Function

UINT16

6206~6207

Reserved

6208

RW

DI1 Debounce

UINT16

1 to 9999 ms,

3) The Self-Read Time applies to both the Peak Demand Log as well as the Max./Min. Log and

supports the following three options:

 A zero value means that the Self-Read will take place at 00:00 of the first day of each month.  A non-zero value means that the Self-Read will take place at a specific time and day based on

the formula: Self-Read Time = (Day x 100 + Hour) where 0 ≤ Hour ≤ 23 and 1 ≤ Day ≤ 28. For example, the value 1512 means that the Self-Read will take place at 12:00pm on the 15th day of each month.

 A 0xFFFF value means the automatic self-read operation is disabled and the log will be

transferred manually.

4) The Delimiter setup register supports two options, 1 and 2:

Option 1: “,” is used as the x1000 delimiter and “.” as the decimal point (e.g. 123,456,789.0). Option 2: “ ” is used as the x1000 delimiter and “,” as the decimal point (e.g. 123 456 789,0).

5) The Monthly Energy Log Self-Read Time and Monthly Freeze Self-Read Time support only two

options:

 A zero value means that the Self-Read will take place at 00:00 of the first day of each month.  A non-zero value means that the Self-Read will take place at a specific time and day based on

the formula: Self-Read Time = Day * 100 + Hour where 0 ≤ Hour ≤ 23 and 1 ≤ Day ≤ 28. For example, the value 1512 means that the Self-Read will take place at 12:00pm on the 15th day of each month.

6) The Daily Freeze Self-Read Time can be set to a zero value or a non-zero value:

 A zero value means that the Self-Read will take place at 00:00 everyday.  A non-zero value means that the Self-Read will take place at a specific time of the day based

on the formula: Self-Read time = (Hour x 100 + Min) where 0 ≤ Hour ≤ 23 and 0 ≤ Min ≤ 59. For example, the value 1512 means that the Self-Read will take place at 15:12 of each day.

7) The following table illustrates the parameters that can be selected for display in the Default Display

screen.

*Available in Firmware V1.00.06 or later

8) The Interval Energy registers will be reset once the EN Period is changed.

9) The DNP Polling Objects are listed in table below:

5.11.2 I/O Setup

Table 5-34 Default Display Parameters

Table 5-35 DNP Polling Objects

70

CET Electric Technology

6209

RW

DI2 Debounce

UINT16

20*

6210

RW

DI3 Debounce

UINT16

6211

RW

DI4 Debounce

UINT16

6212

RW

DI5 Debounce

UINT16

6213

RW

DI6 Debounce

UINT16

6214~6215

Reserved

6216

RW

DI1 Pulse Weight

UINT32

1* to 1000000

6218

RW

DI2 Pulse Weight

UINT32

6220

RW

DI3 Pulse Weight

UINT32

6222

RW

DI4 Pulse Weight

UINT32

6224

RW

DI5 Pulse Weight

UINT32

6226

RW

DI6 Pulse Weight

UINT32

6228 Reserved

UINT32

6230

RW

DO1 Mode#2

UINT16

0 = Remote

Control/Setpoint*

1 = kWh Import 2 = kWh Export

3 = kWh Total

4 = kvarh Import

5 = kvarh Export

6 = kvarh Total

6231

RW

DO2 Mode#2

UINT16

6232

RW

DO3 Mode3

UINT16

6233

RW

DO4 Mode3

UINT16

6234

RW

Reserved

UINT16

-

6235

RW

Reserved

UINT16

-

6236

RW

DO1 Pulse Width

UINT16

0 to 6000 (x0.1s),

10*

(0 = Latch Mode)

6237

RW

DO2 Pulse Width

UINT16

6238

RW

DO3 Pulse Width

UINT16

6239

RW

DO4 Pulse Width

UINT16

6240~6247

Reserved

UINT16

-

6248

RW

RTD 1 Compensation

UINT16

0 to 2000 (x0.01Ω), 0*

6249

RW

RTD 2 Compensation

UINT16

0 to 2000 (x0.01Ω), 0*

6250

RW

AI Type

UINT16

0 = 4~20mA*

1 = 0~20mA

6251

RW

AI Zero Scale

INT32

-999,999 to +999,999 (Default = 400)

6253

RW

AI Full Scale

INT32

-999,999 to +999,999

(Default = 2000)

6255~6259

RW

Reserved

UINT16

-

6260

RW

AO Type

UINT16

0 = 4~20mA*

1 = 0~20mA

6261

RW

AO Key4

UINT16

0* to 19

6262

RW

AO Zero Scale

INT32

-999,999 to +999,999

(Default =0)

6264

RW

AO Full Scale

INT32

-999,999 to +999,999

(Default = 0)

Key

Parameter

Scale

Unit

Key

Parameter

Scale

Unit 0 Uab

x1

V

10

kVA Total

x1

kVA 1 Ubc

V

11

PF Total

x1000

- 2 Uca

V

12

Frequency

x100

-

3

Ull Average

V

13

kW Total Present Demand

x1

kW

4

Ia

A

14

kvar Total Present Demand

kvar

5

Ib

A

15

kVA Total Present Demand

kVA

6

Ic

A

16

Uan

x1 V 7 I Average

A

17

Ubn

V

#

Available in Firmware V1.00.04 or later

Notes:

1) The Tariff Switch option is supported in Firmware V1.00.03 or later.

2) This is available only when the Basic Function option is “3” (4xDI and 2xRelay Output) or “A” (4xDI

3) This is available only when Expansion Module B is equipped with the “B4” option (2xDI and 2xSS

4) Analog Output Parameters:

Table 5-35 I/O Setup Parameters

and 2xSS Pulse Output). Please refer to the Ordering Guide for more details.

Pulse Output). Please refer to the Ordering Guide for more details.

The Units for Voltage, Current, kW, kvar, kVA and Frequency are V, A, kW, kvar, kVA and Hz, respectively.

71

CET Electric Technology

8

kW Total

x1

kW

18

Ucn

V

9

kvar Total

kvar

19

Uln Average

V

Register

Property

Description

Format

Range, Default*

6400

RW

Port1 Protocol

UINT16

0=Modbus RTU*

1=BACnet/MSTP#

2=N2#, 3=DNP~

6401

RW

Port1 Unit ID

UINT16

Modbus RTU/N2: 1 to 247

BACnet/MSTP: 1 to 127

DNP: 0 to 65519

Default=100

6402

RW

Port1 Baud Rate1

UINT16

0=1200, 1=2400, 2=4800,

3=9600*, 4=19200, 5=38400

6403

RW

Port1 Comm. Config.

UINT16

0=8N2, 1=8O1,2=8E1*

3=8N1, 4=8O2, 5=8E2

6404

RW

Port2 Protocol

UINT16

0=Modbus RTU*

6405

RW

Port2 Unit ID

UINT16

1 to 247, 101*

6406

RW

Port2 Baud Rate1

UINT16

0=1200, 1=2400, 2=4800,

3=9600*, 4=19200, 5=38400

6407

RW

Port2 Comm. Config.

UINT16

0=8N2, 1=8O1,2=8E1*

3=8N1, 4=8O2, 5=8E2

Register

Property

Description

Format

Range, Default*

6500

RW

Setpoint #1

Setpoint Type

UINT16

0=Disabled*

1=Over Setpoint

2=Under Setpoint

6501

RW

Parameters1

UINT16

0 to 32

6502

RW

Over Limit

2

Float

0*

6504

RW

Under Limit

2

Float

0*

6506

RW

Active Delay

UINT16

0 to 9999 s, 10*

6507

RW

Inactive Delay

UINT16

0 to 9999 s, 10*

6508

RW

Trigger Action 13

UINT16

0 to 4

6509

RW

Trigger Action 23

UINT16

…

6580

RW

Setpoint #9

Setpoint Type

UINT32

0=Disabled*

1=Over Setpoint

2=Under Setpoint

6581

RW

Parameter1

UINT16

0* to 32

6582

RW

Over Limit

Float

0*

6584

RW

Under Limit

Float

0*

6586

RW

Active Delay

UINT16

0 to 9999 s, 10*

6587

RW

Inactive Delay

UINT16

0 to 9999 s, 10*

6588

RW

Trigger Action 12

UINT16

0 to 4

6589

RW

Trigger Action 22

UINT16

Key

Setpoint Parameter

Scale

Unit

0

None

- - 1

Uln (Any Phase Voltage)

x1

V

2

Ull (Any Line Voltage)

3

I (Any Phase Current)

A

4

In (Calculated)

5

Frequency

Hz

Table 5-36 Analog Output Parameters

5.11.3 Communication Setup Parameters

#

Available in Firmware V1.00.03 or later. Please refer to Appendices C and D for the detailed information of BACnet MSTP and

N2 protocol. ~Available in Firmware V1.00.06 or later. Please refer to Appendix E for the detailed information of DNP.

Table 5-37 Communication Setup

Notes:

1) If the Baud Rate is set to an invalid value, it will default to 9600bps automatically.

5.11.4 Setpoints Setup

Table 5-38 Setpoint Setup Parameters

Notes:

1) The PMC-53A provides the following setpoint parameters:

72

CET Electric Technology

6

P (kW Total)

W

7

Q (kvar Total)

var

8

S (kVA Total)

VA

9

PF (PF Total)

-

10

P DMD (kW Total Present Demand)

W

11

Q DMD (kvar Total Present Demand)

var

12

S (kVA Total Present Demand)

VA

13

P DMD Pred (kW Total Predicted Demand)

W

14

Q DMD Pred (kvar Total Predicted Demand)

var

15

S DMD Pred (kVA Total Predicted Demand)

VA

16

U THD

100%

17

U TOHD

100%

18

U TEHD

100%

19

I THD

100%

20

I TOHD

100%

21

I TEHD

100%

22

U Unbal (Voltage Unbalance)

100%

23

I Unbal (Current Unbalance)

100%

24

Reversal (Phase Reversal)3

-

25

I4 (Measured)*

x1

A

26

AI*

-

27

Reserved

-

28

RTD1*

x1

°C

29

RTD2*

30

Ir (Residual Current)~

x1

A

31

U2~

x1

V

32

U0~

Key

Action

Key

Action 0 None

3

DO3 Closed4

1

DO1 Closed

4

DO4 Closed4

2

DO2 Closed4

Others

Reserved

Register

Property

Description

Format

6600~6622

RW

Data Recorder #1*

See Table 5-42 DR

Setup Parameter Data

Structure

6623~6645

RW

Data Recorder #2*

6646~6668

RW

Data Recorder #3*

6669~6691

RW

Data Recorder #4*

6692~6714

RW

Data Recorder #5*

Offset

Property

Description

Format

Range

+0

RW

Trigger Mode

UINT16

0=Disabled

1=Triggered by Timer

* Valid only if the device is equipped with the appropriate option ~ Available in Firmware V1.00.06

Table 5-39 Setpoint Parameters

2) For Over Setpoint, the setpoint parameter must exceed the Over Limit to become active and go

below the Under Limit to become inactive. For Under Setpoint, the setpoint parameter must go below the Under Limit to become active and

exceed the Over Limit to become inactive.

3) The PMC-53A provides the following Setpoint Triggers:

Table 5-40 Setpoint Triggers

4) Only when DOx Mode is set to Remote Control/Setpoint, setting Setpoint Triggers to DOx Closed

is valid. In addition,  Only when the PMC-53A’s Basic Function option is “3” (4xDI+3xRelay Output) or “A”

(4xDI+2xSS Pulse Output) would setting the Setpoint Trigger to DO1 Closed or DO2 Closed have meaning.

 Only when the Expansion Module B is equipped with the “2xDI + 2xDO (Relay Output)” or

“2xDI + 2xSS Pulse Output” options would setting the Setpoint Trigger to DO3 Closed or DO4

Closed have meaning.

5.11.5 Data Recorder Setup

* Please refer to Appendix B for the default configuration for the Data Recorders.

Table 5-41 Data Recorder Setup

73

CET Electric Technology

+1

RW

Recording Mode1

UINT16

0=Stop-when-Full

1=First-In-First-Out

+2

RW

Recording Depth1

UINT16

0 to 10,000

+3

RW

Recording Interval1

UINT32

60 to 3456000s

+5

RW

Offset Time2

UINT16

0 to 43200s

+6

RW

Number of Parameters1

UINT16

0 to 16

+7

RW

Parameter #11

UINT16

Please refer to Appendices A and B for a complete list

of the Data Recorder

Parameters and the default

configuration for each DR,

respectively.

+8

RW

Parameter #21

UINT16

+9

RW

Parameter #31

UINT16 … RW

…

UINT16

+22

RW

Parameter #161

UINT16

Register

Property

Description

Format

Range/Option

7000

RO

Current Tariff1

UINT16

0=T1, 1=T2, 2=T3, 3=T4 4=T5, 5=T6, 6=T7, 7=T8

7001

RO

Current Season

UINT16

0 to 11

(Season #1 to #12)

7002

RO

Current Period

UINT16

0 to 11

(Period #1 to #12)

7003

RO

Current Daily Profile No.

UINT16

0 to 19

(Daily Profile #1 to #20)

7004

RO

Current Day Type

UINT16

0=Weekday1 1=Weekday2 2=Weekday3

3= Alternate Day

7005

RO

Current TOU No.

UINT16

0=TOU #1 1=TOU #2

7006

RW

TOU Switch Time

UINT32

See Note (1)

7008

WO

Switch TOU Manually

UINT16

Write 0xFF00 to manually switch the TOU schedules

7009

RW

Sunday Setup

UINT16

0=Weekday1*

1=Weekday2 2=Weekday3

7010

RW

Monday Setup

UINT16

7011

RW

Tuesday Setup

UINT16

7012

RW

Wednesday Setup

UINT16

7013

RW

Thursday Setup

UINT16

7014

RW

Friday Setup

UINT16

7015

RW

Saturday Setup

UINT16

Byte 3

Byte 2

Byte 1

Byte 0

Year-2000 (0-37)

Month (1-12)

Day (1-31)

Hour (00-23)

Table 5-42 DR Setup Parameter Data Structure

Notes:

1) Changing any of these Data Recorder setup registers will reset the Data Recorder.

2) Recording Offset can be used to delay the recording by a fixed amount of time from the

Recording Interval. For example, if the Recording Interval is set to 3600 (hourly) and the Recording Offset is set to 300 (5 minutes), the recording will take place at 5 minutes after the

hour every hour, i.e. 00:05, 01:05, 02:05…etc. The value of the Recording Offset parameter should be less than the Recording Interval parameter.

5.12 TOU Setup

5.12.1 Basic

Notes:

1) If DI1 is not programmed as a Tariff Switch, the TOU will function based on the TOU Schedule. If at

least one DI (DI1) is programmed as a Tariff Switch, the TOU Schedule will no longer be used and the Tariff switching will be based on the status of the DIs.

2) The following table illustrates the data structure for the TOU Switch Time. For example, 0x1003140C

indicates a switch time of 12:00pm on March 20th, 2016. Writing 0xFFFFFFFF to this register disables the switching between TOU Schedule.

Table 5-43 TOU Basic Setup

Table 5-44 TOU Switch Time Format

74

CET Electric Technology

Offset

Property

Description

Format

Range/Default*

0

RW

Season #1: Start Date

UINT16

0x0101*

1

RW

Season #1: Weekday#1 Daily Profile

UINT16

0* to 19

2

RW

Season #1: Weekday#2 Daily Profile

UINT16

3

RW

Season #1: Weekday#3 Daily Profile

UINT16

4

RW

Season #2: Start Date

UINT16

High-order Byte: Month

Low-order Byte: Day

5

RW

Season #2: Weekday#1 Daily Profile

UINT16

0* to 19

6

RW

Season #2: Weekday#2 Daily Profile

UINT16

7

RW

Season #2: Weekday#3 Daily Profile

UINT16

8

RW

Season #3: Start Date

UINT16

See Season #2: Start Date

9

RW

Season #3: Weekday#1 Daily Profile

UINT16

0* to 19

10

RW

Season #3: Weekday#2 Daily Profile

UINT16

11

RW

Season #3: Weekday#3 Daily Profile

UINT16

12

RW

Season #4: Start Date

UINT16

See Season #2: Start Date

13

RW

Season #4: Weekday#1 Daily Profile

UINT16

0* to 19

14

RW

Season #4: Weekday#2 Daily Profile

UINT16

15

RW

Season #4: Weekday#3 Daily Profile

UINT16

16

RW

Season #5: Start Date

UINT16

See Season #2: Start Date

17

RW

Season #5: Weekday#1 Daily Profile

UINT16

0* to 19

18

RW

Season #5: Weekday#2 Daily Profile

UINT16

19

RW

Season #5: Weekday#3 Daily Profile

UINT16

20

RW

Season #6: Start Date

UINT16

See Season #2: Start Date

21

RW

Season #6: Weekday#1 Daily Profile

UINT16

0* to 19

22

RW

Season #6: Weekday#2 Daily Profile

UINT16

23

RW

Season #6: Weekday#3 Daily Profile

UINT16

24

RW

Season #7: Start Date

UINT16

See Season #2: Start Date

25

RW

Season #7: Weekday#1 Daily Profile

UINT16

0* to 19

26

RW

Season #7: Weekday#2 Daily Profile

UINT16

27

RW

Season #7: Weekday#3 Daily Profile

UINT16

28

RW

Season #8: Start Date

UINT16

See Season #2: Start Date

29

RW

Season #8: Weekday#1 Daily Profile

UINT16

0* to 19

30

RW

Season #8: Weekday#2 Daily Profile

UINT16

31

RW

Season #8: Weekday#3 Daily Profile

UINT16

32

RW

Season #9: Start Date

UINT16

See Season #2: Start Date

33

RW

Season #9: Weekday#1 Daily Profile

UINT16

0* to 19

34

RW

Season #9: Weekday#2 Daily Profile

UINT16

35

RW

Season #9: Weekday#3 Daily Profile

UINT16

36

RW

Season #10: Start Date

UINT16

See Season #2: Start Date

37

RW

Season #10: Weekday#1 Daily Profile

UINT16

0* to 19

38

RW

Season #10: Weekday#2 Daily Profile

UINT16

39

RW

Season #10: Weekday#3 Daily Profile

UINT16

40

RW

Season #11: Start Date

UINT16

See Season #2: Start Date

41

RW

Season #11: Weekday#1 Daily Profile

UINT16

0* to 19

42

RW

Season #11: Weekday#2 Daily Profile

UINT16

43

RW

Season #11: Weekday#3 Daily Profile

UINT16

44

RW

Season #12: Start Date

UINT16

See Season #2: Start Date

45

RW

Season #12: Weekday#1 Daily Profile

UINT16

0* to 19

46

RW

Season #12: Weekday#2 Daily Profile

UINT16

47

RW

Season #12: Weekday#3 Daily Profile

UINT16

5.12.2 Season

The PMC-53A has two sets of Season setup parameters, one for each TOU. The Base Addresses for the two sets are 7100 and 8100, respectively, where the Register Address = Base Address + Offset. For example, the register address for TOU #1’s Season #2’s Start Date is 7100+4 = 7104.

Notes:

1) Start Date for Season #1 is Jan. 1st and cannot be modified.

2) Setting a Season’s Start Date as 0xFFFF terminates the TOU’s Season settings. All subsequent

Seasons’ setup parameters will be ignored since the previous Season’s duration is from its Start Date to the end of the year.

3) The Start Date of a particular Season must be later than the previous Season’s.

Table 5-45 Season Setup

75

CET Electric Technology

Register

Property

Description

Format

7200~7223

RW

Daily Profile #1

See Table 5-48

Daily Profile Data

Structure

7224~7247

RW

Daily Profile #2

7248~7271

RW

Daily Profile #3

7272~7295

RW

Daily Profile #4

7296~7319

RW

Daily Profile #5

7320~7343

RW

Daily Profile #6

7344~7367

RW

Daily Profile #7

7368~7391

RW

Daily Profile #8

7392~7415

RW

Daily Profile #9

7416~7439

RW

Daily Profile #10

7440~7463

RW

Daily Profile #11

7464~7487

RW

Daily Profile #12

7488~7511

RW

Daily Profile #13

7512~7535

RW

Daily Profile #14

7536~7559

RW

Daily Profile #15

7560~7583

RW

Daily Profile #16

7584~7607

RW

Daily Profile #17

7608~7631

RW

Daily Profile #18

7632~7655

RW

Daily Profile #19

7656~7679

RW

Daily Profile #20

Register

Property

Description

Format

8200~8223

RW

Daily Profile #1

See Table 5-48

Daily Profile Data

Structure

8224~8247

RW

Daily Profile #2

8248~8271

RW

Daily Profile #3

8272~8295

RW

Daily Profile #4

8296~8319

RW

Daily Profile #5

8320~8343

RW

Daily Profile #6

8344~8367

RW

Daily Profile #7

8368~8391

RW

Daily Profile #8

8392~8415

RW

Daily Profile #9

8416~8439

RW

Daily Profile #10

8440~8463

RW

Daily Profile #11

8464~8487

RW

Daily Profile #12

8488~8511

RW

Daily Profile #13

8512~8535

RW

Daily Profile #14

8536~8559

RW

Daily Profile #15

8560~8583

RW

Daily Profile #16

8584~8607

RW

Daily Profile #17

8608~8631

RW

Daily Profile #18

8632~8655

RW

Daily Profile #19

8656~8679

RW

Daily Profile #20

Offset

Property

Description

Format

Note

+0

RW

Period #1 Start Time

UINT16

0x0000

+1

RW

Period #1 Tariff

UINT16

0=T1, …, 7=T8

+2

RW

Period #2

Start Time

High-order Byte: Hour

UINT16

0 ≤ Hour < 24

Low-order Byte: Min

Min = 0, 15, 30, 45

+3

RW

Period #2 Tariff

UINT16

0=T1, …, 7=T8

+4

RW

Period #3 Start Time

UINT16

See Period #2 Start Time

+5

RW

Period #3 Tariff

UINT16

0=T1, …, 7=T8

+6

RW

Period #4 Start Time

UINT16

See Period #2 Start Time

+7

RW

Period #4 Tariff

UINT16

0=T1, …, 7=T8

+8

RW

Period #5 Start Time

UINT16

See Period #2 Start Time

+9

RW

Period #5 Tariff

UINT16

0=T1, …, 7=T8

+10

RW

Period #6 Start Time

UINT16

See Period #2 Start Time

+11

RW

Period #6 Tariff

UINT16

0=T1, …, 7=T8

+12

RW

Period #7 Start Time

UINT16

See Period #2 Start Time

5.12.3 Daily Profile

The PMC-53A has two sets of Daily Profile setup parameters, one for each TOU.

Table 5-46 TOU #1’s Daily Profile Setup

Table 5-47 TOU #2’s Daily Profile Setup

76

CET Electric Technology

+13

RW

Period #7 Tariff

UINT16

0=T1, …, 7=T8

+14

RW

Period #8 Start Time

UINT16

See Period #2 Start Time

+15

RW

Period #8 Tariff

UINT16

0=T1, …, 7=T8

+16

RW

Period #9 Start Time

UINT16

See Period #2 Start Time

+17

RW

Period #9 Tariff

UINT16

0=T1, …, 7=T8

+18

RW

Period #10 Start Time

UINT16

See Period #2 Start Time

+19

RW

Period #10 Tariff

UINT16

0=T1, …, 7=T8

+20

RW

Period #11 Start Time

UINT16

See Period #2 Start Time

+21

RW

Period #11 Tariff

UINT16

0=T1, …, 7=T8

+22

RW

Period #12 Start Time

UINT16

See Period #2 Start Time

+23

RW

Period #12 Tariff

UINT16

0=T1, …, 7=T8

Offset

Property

Description

Format

Range/Default*

0

RW

Alternate Day #1 Date¹

UINT32

Table 5-50

2

RW

Alternate Day #1 Daily Profile

UINT16

0* to 19

3

RW

Alternate Day #2 Date¹

UINT32

Table 5-50

5

RW

Alternate Day #2 Daily Profile

UINT16

0* to 19

6

RW

Alternate Day #3 Date¹

UINT32

Table 5-50

8

RW

Alternate Day #3 Daily Profile

UINT16

0* to 19

9

RW

Alternate Day #4 Date¹

UINT32

Table 5-50

11

RW

Alternate Day #4 Daily Profile

UINT16

0* to 19

12

RW

Alternate Day #5 Date¹

UINT32

Table 5-50

14

RW

Alternate Day #5 Daily Profile

UINT16

0* to 19

15

RW

Alternate Day #6 Date¹

UINT32

Table 5-50

17

RW

Alternate Day #6 Daily Profile

UINT16

0* to 19

18

RW

Alternate Day #7 Date¹

UINT32

Table 5-50

19

RW

Alternate Day #7 Daily Profile

UINT16

0* to 19

21

RW

Alternate Day #8 Date¹

UINT32

Table 5-50

22

RW

Alternate Day #8 Daily Profile

UINT16

0* to 19

24

RW

Alternate Day #9 Date¹

UINT32

Table 5-50

25

RW

Alternate Day #9 Daily Profile

UINT16

0* to 19

27

RW

Alternate Day #10 Date¹

UINT32

Table 5-50

29

RW

Alternate Day #10 Daily Profile

UINT16

0* to 19

…

Table 5-50

…

0* to 19

240

RW

Alternate Day #81 Date¹

UINT32

Table 5-50

162

RW

Alternate Day #81 Daily Profile

UINT16

0* to 19

243

RW

Alternate Day #82 Date¹

UINT32

Table 5-50

245

RW

Alternate Day #82 Daily Profile

UINT16

0* to 19

246

RW

Alternate Day #83 Date¹

UINT32

Table 5-50

248

RW

Alternate Day #83 Daily Profile

UINT16

0* to 19

249

RW

Alternate Day #84 Date¹

UINT32

Table 5-50

251

RW

Alternate Day #84 Daily Profile

UINT16

0* to 19

Table 5-48 Daily Profile Data Structure

Notes:

1) Daily Profile #1’s Period #1 Start Time is always 00:00 and cannot be modified.

2) Setting a Period’s Start Time as 0xFFFF terminates the Daily Profile’s settings. All subsequent Daily

Profiles’ setup parameters will be ignored, and the previous Period’s duration is from its Start Time to the end of the day.

3) The minimum interval of a period is 15 minutes.

4) The Start Time of a particular Period must be later than the previous Period’s .

5.12.4 Alternate Days

Each Alternate Day is assigned a Daily Profile and has a higher priority than Season. If a particular date is set as an Alternate Day, its assigned Daily Profile will override the “normal” Daily Profile for this day according the TOU settings.

The PMC-53A has two sets of Alternate Days setup parameters, one for each TOU. The Base Addresses for the two sets are 7700 and 8700, respectively, where the Register Address = Base Address + Offset. For example, the register address for TOU #2’s Alternative Day #2’s Date is 8700+3 = 8703.

77

CET Electric Technology

252

RW

Alternate Day #85 Date¹

UINT32

Table 5-50

254

RW

Alternate Day #85 Daily Profile

UINT16

0* to 19

255

RW

Alternate Day #86 Date¹

UINT32

Table 5-50

256

RW

Alternate Day #86 Daily Profile

UINT16

0* to 19

258

RW

Alternate Day #87 Date¹

UINT32

Table 5-50

260

RW

Alternate Day #87 Daily Profile

UINT16

0* to 19

261

RW

Alternate Day #88 Date¹

UINT32

Table 5-50

263

RW

Alternate Day #88 Daily Profile

UINT16

0* to 19

264

RW

Alternate Day #89 Date¹

UINT32

Table 5-50

266

RW

Alternate Day #89 Daily Profile

UINT16

0* to 19

267

RW

Alternate Day #90 Date¹

UINT32

Table 5-50

269

RW

Alternate Day #90 Daily Profile

UINT16

0* to 19

Byte 3

Byte 2

Byte 1

Byte 0

Reserved

Year-2000 (0-37)

Month (1-12)

Day (1-31)

Register

Property

Description

Format

Note

60000

9000

RW

High-order Byte: Year

UINT16

0-37 (Year-2000)

Low-order Byte: Month

1 to 12

60001

9001

RW

High-order Byte: Day

UINT16

1 to 31

Low-order Byte: Hour

0 to 23

60002

9002

RW

High-order Byte: Minute

UINT16

0 to 59

Low-order Byte: Second

0 to 59

60003

9003

RW

Millisecond

UINT16

0 to 999

60004

~

60005

9004

~

9005

RW

UNIX Time

UINT32

0x386D4380 to 0x 7FE8177F

The corresponding time is

2000.01.01 00:00:00 to

2037.12.31 23:59:59

(GMT 0:00 Time Zone)

Table 5-49 Alternate Days Setup

Notes:

1) The following table illustrates the data structure of the Date register:

Table 5-50 Date Format

When the Year and/or Month are set as 0xFF, it means the Alternate Day is repetitive by year and/or month, i.e. the same day of every year or every month is an Alternate Day.

5.13 Time

There are two sets of Time registers supported by the PMC-53A – Year / Month / Day / Hour / Minute / Second (Registers # 60000 to 60002) and UNIX Time (Register # 60004). When sending time to the PMC53A over Modbus communications, care should be taken to only write one of the two Time register sets. All registers within a Time register set must be written in a single transaction. If registers 60000 to 60004 are being written to at the same time, both Time register sets will be updated to reflect the new time specified in the UNIX Time register set (60004) and the time specified in registers 60000-60002 will be ignored. Writing to the Millisecond register (60003) is optional during a Time Set operation. When broadcasting time, the function code must be set to 0x10 (Pre-set Multiple Registers). Incorrect date or time values will be rejected by the meter. In addition, attempting to write a Time value less than Jan 1, 2000 00:00:00 will be rejected.

5.14 Remote Control

The DO Control registers are implemented as both “Write-Only” Modbus Coil Registers (0XXXXX) and Modbus Holding Registers (4XXXXX), which can be controlled with the Force Single Coil command (Function Code 0x05) or the Preset Multiple Hold Registers (Function Code 0x10). The PMC-53A does not support the Read Coils command (Function Code 0x01) because DO Control registers are “WriteOnly”. The DO Status register 0098 should be read instead to determine the current DO status.

The PMC-53A adopts the ARM before EXECUTE operation for the remote control of its Digital Outputs

Table 5-51 Time Registers

78

CET Electric Technology

Register

Property

Description

Format

Note

9100

WO

Arm DO1 Close

UINT16

Writing “0xFF00”

to the register to

perform the

described action.

9101

WO

Execute DO1 Close

UINT16

9102

WO

Arm DO1 Open

UINT16

9103

WO

Execute DO1 Open

UINT16

9104

WO

Arm DO2 Close

UINT16

9105

WO

Execute DO2 Close

UINT16

9106

WO

Arm DO2 Open

UINT16

9107

WO

Execute DO2 Open

UINT16

9108

WO

Arm DO3 Close

UINT16

9109

WO

Execute DO3 Close

UINT16

9110

WO

Arm DO3 Open

UINT16

9111

WO

Execute DO3 Open

UINT16

9112

WO

Arm DO4 Close

UINT16

9113

WO

Execute DO4 Close

UINT16

9114

WO

Arm DO4 Open

UINT16

9115

WO

Execute DO4 Open

UINT16

Register

Property

Description

Format

Note

9600

WO

Clear Historical Monthly Energy Log1

UINT16

Writing “0xFF00”

to the register to

execute the

described action.

9601

WO

Clear All Energy Registers2

9602

WO

Clear Present Monthly Energy Log3

9603

WO

Clear Peak Demand of

This Month (Since Last Reset)4

9604

WO

Clear All Demand Registers5

9605

WO

Clear Max/Min Logs of This Month

(Since Last Reset)6

9606

WO

Clear All Max./Min. Log7

9607

WO

Clear Device Operating Time

9608

WO

Clear All Data8

9609

WO

Clear SOE Log

9610

WO

Clear DI1 Pulse Counter

9611

WO

Clear DI2 Pulse Counter

9612

WO

Clear DI3 Pulse Counter

9613

WO

Clear DI4 Pulse Counter

9614

WO

Clear DI5 Pulse Counter

9615

WO

Clear DI6 Pulse Counter

9616

WO

Reserved

9617

WO

Reserved

9618

WO

Clear All Pulse Counters

9619

WO

Clear Data Recorder #1 Log

9620

WO

Clear Data Recorder #2 Log

9621

WO

Clear Data Recorder #3 Log

9622

WO

Clear Data Recorder #4 Log

9623

WO

Clear Data Recorder #5 Log

9624

WO

Clear All Data Recorder Log

if this function is enabled through the Arm Before Execute Enable Setup register (6032), which is disabled by default. Before executing an OPEN or CLOSE command on a Digital Output, it must be

“Armed” first. This is achieved by writing the value 0xFF00 to the appropriate register to “Arm” a particular DO operation. The DO will be “Disarmed” automatically if an “Execute” command is not received within 15 seconds after it has been “Armed”. If an “Execute” command is received without first having received an “Arm” command, the meter ignores the “Execute” command and returns the 0x04

exception code.

5.15 Clear/Reset Control

Table 5-52 DO Control

Notes:

1) Writing 0xFF00 to the Clear Historical Monthly Energy Log register to clear the Monthly Energy Log

of the last 1 to 12 months, excluding the Monthly Energy Log for the Present Month.

Table 5-53 Clear Control

79

CET Electric Technology

Register

Property

Description

Format

Note

60200~60219

9800~9819

RO

Meter model1

UINT16

See Note 1)

60220

9820

RO

Firmware Version

UINT16

e.g. 10000 shows the

version is V1.00.00

60221

9821

RO

Protocol Version

UINT16

e.g. 10 shows the

version is V1.0

60222

9822

RO

Firmware Update

Date: Year-2000

UINT16

e.g. 140110 means

January 10, 2014 60223

9823

RO

Firmware Update

Date: Month

UINT16

60224

9824

RO

Firmware Update

Date: Day

UINT16

60225

9825

RO

Serial Number

UINT32

e.g. 1701030100 means

the 100th PEM353 that

was manufactured on

January 3rd, 2017

60227

9827

RO

Reserved

UINT16

60228

9828

RO

Reserved

UINT16

60229

9829

RO

Feature Code

UINT16

Bit 0 to Bit 2 (Expansion A): 000=None 001=RS485 010=I4 011=SPI

Bit 3 to Bit 5 (Expansion B): 000=None 001=1xAI + 1xAO 010=2xDI + 2xDO 011=2xRTD 100=2xDI + 2x SS Pulse Output 101=Reserved

Bit 6 (Flash): 0=Disabled 1=Enabled

Bit 8 to Bit 7 (Basic Function): 00=4xDI + 2xDO 01=None 10=4xDI + 2 x SS Pulse

2) Writing 0xFF00 to the Clear All Energy Registers register to clear the 3-Ø Total and Per-Phase energy

registers.

3) Writing 0xFF00 to the Clear Present Monthly Energy Log register to clear the Monthly Energy Log

of the Present Month.

4) Writing 0xFF00 to the Clear Peak Demand of This Month register to clear Peak Demand Log of This

Month (Since Last Reset) when the Self-Read Time register is set for automatic Self-Read operation. The Peak Demand of Last Month will not be cleared. If the Self-Read Time register is set for manual operation with a register value of 0xFFFF, the Peak Demand of This Month (Since Last Reset) will be transferred to the Peak Demand of Last Month (Before Last Reset) and then cleared.

5) Writing 0xFF00 to the Clear All Demand register to clear all Demand registers and logs, including

Real-time Present Demand, Peak Demand Log of This Month (Since Last Reset) and Last Month (Before Last Reset).

6) Writing 0xFF00 to the Clear Max./Min. Log of This Month register to clear the Max./Min. log of

This Month (Since Last Reset) when the Self-Read Time register is set for automatic Self-Read operation. The Max./Min. log of Last Month will not be cleared. If the Self-Read Time register is set for manual operation with a register value of 0xFFFF, the Max./Min. log of This Month (Since Last Reset) will be transferred to the Max./Min. log of Last Month (Before Last Reset) and then cleared.

7) Writing 0xFF00 to the Clear All Max./Min. Log register to clear both the Max./Min Log of This

Month (Since Last Reset) and the Max./Min. Log of Last Month (Before Last Reset).

8) Writing 0xFF00 to the Clear All Data register to perform the Clear operation for the actions specified

in registers # 9600 to 9607, registers # 9609 to # 9615, registers # 9618 to 9624 and Daily and Monthly Freeze Logs.

5.16 Meter Information

80

CET Electric Technology

Output

Bit 15 to Bit 16: Reserved

Register

Value(Hex)

ASCII

60200

0x50

P

60201

0x4D

M

60202

0x43

C

60203

0x2D

-

60204

0x35

5

60205

0x33

3

60206

0x41

A

60207-60219

0x20

Null

* Available in Firmware V1.00.04 or later

Table 5-54 Meter Information

Notes:

1) The Meter Model appears from registers 60200 to 60219 and contains the ASCII encoding of the

string “PMC-53A” as shown in the following table.

Table 5-55 ASCII Encoding of “PMC-53A”

81

CET Electric Technology

ID

Description

ID

Description

ID

Description

Real-time Measurements

0

None

14

kWb

28

PF Total

1

Uan

15

kWc

29

Frequency

2

Ubn

16

kW Total

30

Uan/Uab Angle

3

Ucn

17

kvara

31

Ubn/Ubc Angle

4

Uln Average

18

kvarb

32

Ucn/Uca Angle

5

Uab

19

kvarc

33

Ia Angle

6

Ubc

20

kvar Total

34

Ib Angle

7

Uca

21

kVAa

35

Ic Angle

8

Ull Average

22

kVAb

36

In (Calculated)

9

Ia

23

kVAc

37

I4

10

Ib

24

kVA Total

38

RTD 1

11

Ic

25

PFa

39

RTD 2

12

I Average

26

PFb

40

AI Scaled

13

kWa

27

PFc

332

Ir* (Residual Current)

Power Quality

41

Phase A Fundamental kW

59

Ib Crest -Factor

160

Ubn/Ubc HD31

42

Phase B Fundamental kW

60

Ic Crest -Factor

161

Ucn/Uca HD31

43

Phase C Fundamental kW

61

Voltage Unbalance

162

Ia THD

44

Fundamental kW Total

62

Current Unbalance

163

Ib THD

45

Total Harmonic kW

63

Uan/Uab THD

164

Ic THD

46

Ia TDD

64

Ubn/Ubc THD

165

Ia TOHD

47

Ib TDD

65

Ucn/Uca THD

166

Ib TOHD

48

Ic TDD

66

Uan/Uab TOHD

167

Ic TOHD

49

Ia TOHD

67

Ubn/Ubc TOHD

168

Ia TEHD

50

Ib TOHD

68

Ucn/Uca TOHD

169

Ib TEHD

51

Ic TOHD

69

Uan/Uab TEHD

170

Ic TEHD

52

Ia TEHD

70

Ubn/Ubc TEHD

171

Ia HD02

53

Ib TEHD

71

Ucn/Uca TEHD

172

Ib HD02

54

Ic TEHD

72

Uan/Uab HD02

173

Ic HD02

55

Ia K-Factor

73

Ubn/Ubc HD02

… … 56

Ib K-Factor

74

Ucn/Uca HD02

258

Ia HD31

57

Ic K-Factor

… … 259

Ib HD31

58

Ia Crest-Factor

159

Uan/Uab HD31

260

Ic HD31

Energy Measurements

261

DI1 Pulse Counter

281

kWh Export of T1

301

kWh Export of T5

262

DI2 Pulse Counter

282

kvarh Import of T1

302

kvarh Import of T5

263

DI3 Pulse Counter

283

kvarh Export of T1

303

kvarh Export of T5

264

DI4 Pulse Counter

284

kVAh of T1

304

kVAh of T5

265

DI5 Pulse Counter

285

kWh Import of T2

305

kWh Import of T6

266

DI6 Pulse Counter

286

kWh Export of T2

306

kWh Export of T6

267

kWh Import

287

kvarh Import of T2

307

kvarh Import of T6

268

kWh Export

288

kvarh Export of T2

308

kvarh Export of T6

269

kWh Net

289

kVAh of T2

309

kVAh of T6

270

kWh Total

290

kWh Import of T3

310

kWh Import of T7

271

kvarh Import

291

kWh Export of T3

311

kWh Export of T7

272

kvarh Export

292

kvarh Import of T3

312

kvarh Import of T7

273

kvarh Net

293

kvarh Export of T3

313

kvarh Export of T7

274

kvarh Total

294

kVAh of T3

314

kVAh of T7

275

kVAh

295

kWh Import of T4

315

kWh Import of T8

276

kvarh Q1

296

kWh Export of T4

316

kWh Export of T8

277

kvarh Q2

297

kvarh Import of T4

317

kvarh Import of T8

278

kvarh Q3

298

kvarh Export of T4

318

kvarh Export of T8

279

kvarh Q4

299

kVAh of T4

319

kVAh of T8

280

kWh Import of T1

300

kWh Import of T5

Demand Measurements

320

Ia Present Demand

326

Ia Peak Demand Log of This Month (Since Last Reset)

321

Ib Present Demand

327

Ib Peak Demand Log of This Month (Since Last Reset)

322

Ic Present Demand

328

Ic Peak Demand Log of This Month (Since Last Reset)

323

kW Total Present Demand

329

kW Peak Demand Log of This Month (Since Last Reset)

324

kvar Total Present Demand

330

kvar Peak Demand Log of This Month (Since Last Reset)

325

kVA Total Present Demand

331

kVA Peak Demand Log of This Month (Since Last Reset)

Appendix A Data Recorder Parameter List

* Available in Firmware V1.00.06 or later

82

CET Electric Technology

Parameter

DR 1

DR 2

DR 3

DR 4

DR 5

Trigger Mode

Triggered by

Timer

Triggered by

Timer

Triggered by

Timer

Triggered by

Timer

Triggered by

Timer

Recording Depth

5760

Recording Interval

900s

Recording Offset

0 0 0 0 0

Number of Parameters

15

16

15

16

Parameter 1

kWh Import

Uab

Uan

Uan/Uab THD

T1 kWh Imp.

Parameter 2

kWh Export

Ubc

Ubn

Ubn/Ubc THD

T1 kWh Exp.

Parameter 3

kWh Total

Uca

Ucn

Ucn/Uca THD

T1 kvarh Imp.

Parameter 4

kWh Net

Ull avg

Uln avg

Ia THD

T1 kvarh Exp.

Parameter 5

kvarh Import

Ia

kWa

Ib THD

T2 kWh Imp.

Parameter 6

kvarh Export

Ib

kWb

Ic THD

T2 kWh Exp.

Parameter 7

kvarh Total

Ic

kWc

Ia TDD

T2 kvarh Imp.

Parameter 8

kvarh Net

I avg

kvara

Ib TDD

T2 kvarh Exp.

Parameter 9

kVAh Total

In

(Calculated)

kvarb

Ic TDD

T3 kWh Imp.

Parameter 10

kW Total

Demand

kW Total

kvarc

Ia K-Factor

T3 kWh Exp.

Parameter 11

kvar Total

Demand

kvar Total

kVAa

Ib K-Factor

T3 kvarh Imp.

Parameter 12

kVA Total

Demand

kVA Total

kVAb

Ic K-Factor

T3 kvarh Exp.

Parameter 13

Ia Demand

PF Total

kVAc

Ia

Crest Factor

T4 kWh Imp.

Parameter 14

Ib Demand

Freq

P.F.a

Ib

Crest Factor

T4 kWh Exp.

Parameter 15

Ic Demand

V Unbalance

P.F.b

Ic Crest Factor

T4 kvarh Imp.

Parameter 16

None

I Unbalance

P.F.c

None

T4 kvarh Exp.

Appendix B Data Recorder Default Settings

83

CET Electric Technology

Item

Description

Date

March 20, 2017

Vendor Name

CET

Model Name

PMC-53A

Applications Software Version

1.00.03

Firmware Revision

1.0

Protocol Version

1

Protocol Revision

7

Description

Intelligent Multifunction Meter

Standardized Device

BACnet Smart Actuator (B-SA)

Interoperability Building

Blocks supported

DS-RP-B, DS-RPM-B, DS-WP-B, DM-DOB-B, DM-TS-B, DM-DDB-B

Segmentation Capability

Not Supported

Data Link Layer Options

MS/TP Master, Baud rate(s): 1200, 2400, 4800, 9600, 19200,

38400

Device Address Binding

None

Networking Options

None

Character Sets Support

ANSI X3.4

Property*

Description

Range/Values

Default

R/W

Object_Identifier

0 to 4194302

26001

R/W

Object_Name

Up to 32 characters

Simple Server

R/W

System_Status

Operational (0)

R

Object_Type

Device (8)

R

Vendor_Name

CET

R/W

Vendor_Identifier

593

R

Model_Name

PMC-53A

R

Firmware_Revision

1

R

Application_Software_Version

1.00.03

R/W

Location

Up to 64 characters

LOCAL

R/W

Description

Up to 64 characters

Intelligent

Multifunction Meter

R

Protocol_Version

1

R

Protocol_Revision

7

R

Protocol_Service_Supported1

Please see notes below

R

Protocol_Object_Types_Supported2

Please see notes below

R

Object_List

Please refer to sections

3) to 6)

R

Max_APDU_Length_Accepted

480

R Segmentation

NO_SEGMENTATION

Appendix C BACNet MSTP Implementation

1) Basic Information

The PMC-53A with the Firmware V1.00.03 or later supports the BACnet MS/TP protocol and can easily be connected to a BACnet MS/TP network using an off-the shelf BACnet router. The PMC53A provides four types of BACnet objects. Standard Protocol Implementation Conformance Statement (PICS) as illustrated in table below describes the required characteristics of the BACnet implementation.

2) Device Objects

 Optional Properties Supported: Description, Local_Time, Local_Date, Location  Writable Properties: Object_Identifier, Number_Of_APDU_Reries, APDU_Timeout,

System_Status, Object_Name, Location, Description, Max_Master, Max_Info_Frame, Local_Time, Local_Date

 Property Range Restrictions: Object_Identifier - valid range is between 0 and 4194302;

Object_Name - limited to 32 characters; Location - limited to 64 characters; Description limited to 64 characters; Max_Master – valid range is between 1 and 127.

The following table illustrates the Device Objects on the PMC-53A:

84

(3)

R/W

APDU_Timeout

0~65535

3000

R/W

Number_Of_APDU_Retries

0~255

3

R/W

Max_Master

1 to 127

127

R/W

Max_Info_Frame

1

R

Device_Address_Binding

{}

R

Database_Revision

0

R

Local_Time

Configuration by

timing

12:00:00:00 R Local_Date

Configuration by

timing

2016.07.01

*

Register

Description

Property

Unit

Range

AI 0000

Uan1

R V

AI 0002

Ubn1

R

AI 0004

Ucn1

R

AI 0006

ULN average1

R

AI 0008

Uab

R

AI 0010

Ubc

R

AI 0012

Uca

R

AI 0014

ULL average

R

AI 0016

Ia

R A

AI 0018

Ib

R

AI 0020

Ic

R

AI 0022

I average

R

AI 0024

kWa1

R

kW

AI 0026

kWb1

R

AI 0028

kWc1

R

AI 0030

kW Total

R

AI 0032

kvara1

R

kvar

AI 0034

kvarb1

R

AI 0036

kvarc1

R

AI 0038

kvar Total

R

AI 0040

kVAa1

R

kVA

R = Read Only; R/W = Read/Write

Notes:

1) Supported services:

o ReadProperty o ReadPropertyMultiple o WriteProperty o TimeSynchronization o Who-Has o Who-Is, I-Am, I-Have

2) Supported object types:

o Analog-Input o Analog-Value o Binary-Input o Binary-Output o Device

CET Electric Technology

3) Analog Input Objects (PMC-53A’s Real-Time Parameters)

Optional Properties Supported: Description, Reliability

Use the Present_Value property of the Analog_Input objects for all read-only numeric variables in PMC-53A. These objects support the Description and Reliability optional properties and all required Analog_Input object properties. None of them are writable. The values that are not instantaneous (i.e. Accumulated Energy, Peak Demand) are non-volatile.

85

CET Electric Technology

AI 0042

kVAb1

R

AI 0044

kVAc1

R

AI 0046

kVA Total

R

AI 0048

PFa1

R

0 to 1

AI 0050

PFb1

R

AI 0052

PFc1

R

AI 0054

PF Total

R

AI 0056

Frequency

R

Hz

AI 0070

Neutral Current (Calculated)

R A

AI 0072

I4 (Optional Measurement)

R A

AI 0082

AI

R

AI 0086

RTD1

R ℃

AI 0088

RTD2

R ℃

AI 0090

AO

R

AI 0174

Ir

R A

AI 0500

kWh Import

R

kWh

0 to

99999999.9

AI 0502

kWh Export

R

AI 0504

kWh Net

R

AI 0506

kWh Total

R

AI 0508

kvarh Import*

R

kvarh

AI 0510

kvarh Export*

R

AI 0512

kvarh Net*

R

AI 0514

kvarh Total*

R

AI 0516

kVAh*

R

kWh

AI 3006

kW Total Demand

R

kW

AI 3008

kvar Total Demand

R

kvar

AI 3010

kVA Total Demand

R

kVA

AI 3000

Ia Demand

R A

AI 3002

Ib Demand

R

AI 3004

Ic Demand

R

AI 3418

kW Total Peak Demand

R

kW

AI 3424

kvar Total Peak Demand

R

kvar

AI 3430

kVA Total Peak Demand

R

kVA

AI 3400

Ia Peak Demand

R A

AI 3406

Ib Peak Demand

R

AI 3412

Ic Peak Demand

R

AI 1600

Uan THD2

R %

AI 1602

Ubn THD2

R

AI 1604

Ucn THD2

R

AI 1400

Ia THD

R

AI 1402

Ib THD

R

AI 1404

Ic THD

R

AI 1318

Ia K Factor

R

AI 1320

Ib K Factor

R

AI 1322

Ic K Factor

R

AI 1300

Ia TDD

R

AI 1302

Ib TDD

R

AI 1304

Ic TDD

R

AI 1324

Ia Crest Factor

R

AI 1326

Ib Crest Factor

R

AI 1328

Ic Crest Factor

R

AI 1330

U Unbalance

R

AI 1332

I Unbalance

R

AI 0074

dPFa1

R

-

0 to 1

AI 0076

dPFb1

R

AI 0078

dPFc1

R

AI 0058

Uan Angle3

R °

AI 0060

Ubn Angle3

R

AI 0062

Ucn Angle3

R

AI 0064

Ia Angle

R

AI 0066

Ib Angle

R

AI 0068

Ic Angle

R

AI 0104

Operating Time

R h

AI 0526

Interval kWh Import

R

kWh

0 to

99999999.9 AI 0528

Interval kWh Export

R

AI 0530

Interval kvarh Import*

R

kvarh

86

CET Electric Technology

AI 0532

Interval kvarh Export*

R

AI 0534

Interval kVAh*

R

kWh

AI 1200

DI #1 Counter

R

-

0 to

999,999,999

AI 1202

DI #2 Counter

R

AI 1204

DI #3 Counter

R

AI 1206

DI #4 Counter

R

AI 1208

DI #5 Counter

R

AI 1210

DI #6 Counter

R

Register

Description

Property

Unit/ Range

Default/Note

AV 6000

PT Primary High#

R/W

0 to 1000 kV

0

AV 6001

PT Primary Low#

R/W

1 to 999 V

100

AV 6002

PT Secondary#

R/W

1 to 690

100

AV 6004

CT Primary

R/W

1 to 30000

5

AV 6006

CT Secondary

R/W

1 to 5

5

AV 6012

I4 Primary

R/W

1 to 30000

5

AV 6014

I4 Secondary

R/W

1 to 5

5

AV 6020

Wiring Mode

R/W

0 = DEMO 1 = 1P2W L-N 2 = 1P2W L-L,

3 = 1P3W L-L-N

4 = 3P3W, 5 = 3P4W

5

AV 6021

PF Convention

R/W

0 = IEC, 1 = IEEE, 2 = -IEEE

0

AV 6022

kVA Calculation

R/W

0 = Vector, 1 = Scalar

0

AV 6028

THD Calculation

R/W

0 = THDf, 1 = THDr

0

AV 6029

Demand Period

R/W

1 to 60 min

15

AV 6030

Number of Sliding Windows

R/W

1 to 15

1

AV 6047

Interval Energy Period

R/W

5 to 60 min

60

AV 9603

Clear Present Peak Demand

W

65280

Default = 0

Writing

“0xFF00” to the

register to

execute the

described

action.

AV 9601

Clear Energy

W

65280

AV 9610

Clear DI #1 Counter

W

65280

AV 9611

Clear DI #2 Counter

W

65280

AV 9612

Clear DI #3 Counter

W

65280

AV 9613

Clear DI #4 Counter

W

65280

AV 9614

Clear DI #5 Counter

W

65280

*There are no unit types for kvarh and kVAh in BACnet so the return values are in unit of kWh.

Notes:

1) When the Wiring Mode is 3P3W, the per phase line-to-neutral voltages, kWs, kvars, kVAs and

PFs have no meaning, and their registers are reserved.

2) Uan/Ubn/Ucn THD = Uab/Ubc/Uca THD in 3P3W Wiring Mode and represent the harmonics

of the line voltages.

3) Uan/Ubn/Ucn Angle = Uab/Ubc/Uca Angle in 3P3W Wiring Mode and represent the phase

angles of the line voltages.

4) Analog Value Objects (PMC-53A’s Basic Setup Registers)

Optional Properties Supported: Description, Relinquish_Default, Priority_Array

Writable Properties: Present_Value, Out_Of_Service, Units, Relinquish_Default

Use the Present Value property of the Analog Value object for some writable variables in the meter other than those used specifically for BACnet configuration or Time Synchronization. Values are checked when written, and errors are returned for invalid entries. The table below describes how the Setup Registers of the PMC-53A are represented in BACnet, their valid ranges, their defaults as well as how they are used. PMC-53A supports the Description, Relinquish_Default and Priority_Array optional properties. Writable properties include Present_Value, Out_Of_Service, Units and Relinquish_Default, but Units are not non-volatile after modification.

87

CET Electric Technology

AV 9615

Clear DI #6 Counter

W

65280

Register

Description

Property

Note

BI0

DI 1

R

0 = Inactive, 1 = Active

BI1

DI 2

R

0 = Inactive, 1 = Active

BI2

DI 3

R

0 = Inactive, 1 = Active

BI3

DI 4

R

0 = Inactive, 1 = Active

BI4

DI 5

R

0 = Inactive, 1 = Active

BI5

DI 6

R

0 = Inactive, 1 = Active

Register

Description

Property

Note

BO0

DO 1

R/W

0 = Inactive, 1 = Active

BO1

DO 2

R/W

0 = Inactive, 1 = Active

BO2

DO 3

R/W

0 = Inactive, 1 = Active

BO3

DO 4

R/W

0 = Inactive, 1 = Active

Parameters

Description

Option/Range

Default

MAC

MS/TP ID^

0 to127

100

INST

Object Identifier#

0 to 4194302

26001

MAXMAS

Maximum Number of Master

0 to 127

127

LOCK

Disable communication

YES/NO

NO

BAUD

Baud rate

1200/2400/4800/9600/19200/38400

9600

CONFIG

Comm. Port Configuration

8N1/8E1/8O1/8N2/8E2/8O2

8E1

#

PT Ratio × CT Ratio × Rated Phase Voltage Input × Rated Current Input x √3 must be less than 790,000,000.

5) Binary Input Objects (PMC-53A’s Digital Inputs)

Optional Properties Supported: Description, Reliability

Use the Present_Value properties of the Binary_Input objects as alerts for conditions of potential concern regarding system measurements. These objects support the Description and Reliability optional properties and all required Binary_Input object properties. None of them are writable.

6) Binary Output Objects (PMC-53A’s Digital Outputs)

Optional Properties Supported: Inactive_Text, Active_Text

Use the Present_Value property of the Binary_Output objects as alerts for DO conditions. Reading Binary_Output objects have the highest priority. PMC-53A supports Inactive_Text, Active_Text optional properties and all required Binary_Output object properties. Present_Value, Out_Of_Service and Polarity properties can be written, but these are non-volatile after modification. The Present_Value can only be written when the Out_Of_Service is true to change the state of the Digital Output and will be written as W when the Out_Of_Service is false.

7) Additional Front Panel Setup Parameters for BACnet MS/TP

The following BACnet MS/TP setup parameters should be configured via the PMC-53A’s Front Panel before connecting the PMC-53A to a BACnet MS/TP network.

^

The MS/TP ID is similar to the Modbus unit ID conceptually

#

The Object Identifier is similar to the IP address of an Ethernet network conceptually and is required to be

unique within the entire BACnet network

88

CET Electric Technology

Item

Description

Device Address

1-247 (100*)

Baud Rate

1200/2400/4800/9600*/19200/38400

Interface

RS485 Half Duplex

Word Length

8

Stop Bits

1*/2

Parity

Even*/Odd/None

Command

PMC-53A’s Response

Identify Device Type

VND

Synchronization Time

Supported

Poll Without Ack

Always respond with No COS Poll Response

Poll With Ack

Always respond with No COS Poll Response

Read Analog Input

Supported

Override Analog Input

Only used to override the Command Register. When an unsupported command is received, the PMC-53A will respond with the Undefined

Command Error Code 0x01.

AI

PMC-53A

AI

Point

PMC-53A

Point

Parameter

Unit

Parameter

Unit 1 Uan1

V

47

kW Total Peak Demand

kW

2

Ubn1

48

kvar Total Peak Demand

kvar 3 Ucn1

49

kVA Total Peak Demand

kVA 4 ULN average1

50

Ia Peak Demand

A

5

Uab

V

51

Ib Peak Demand

6

Ubc

52

Ic Peak Demand

7

Uca

53

Uan THD2

%

8

ULL average

54

Ubn THD2

9

Ia

A

55

Ucn THD2

10

Ib

56

Ia THD

11

Ic

57

Ib THD

12

I average

58

Ic THD

13

kWa1

kW

59

Ia K Factor

-

14

kWb1

60

Ib K Factor

15

kWc1

61

Ic K Factor

16

kW Total

62

Ia TDD

%

17

kvara1

kvar

63

Ib TDD

18

kvarb1

64

Ic TDD

19

kvarc1

65

Ia Crest Factor

-

20

kvar Total

66

Ib Crest Factor

21

kVAa1

kVA

67

Ic Crest Factor

22

kVAb1

68

U Unbalance

%

23

kVAc1

69

I Unbalance

24

kVA Total

70

dPFa

-

25

PFa1

-

71

dPFb

Appendix D N2 Implementation

The PMC-53A with Firmware V1.00.03 or later supports the JCI's Metasys N2 protocol, in addition to BACnet MS/TP, which allows it to connect directly to the Metasys N2 Network. The user can select the desired protocol via the Front Panel's COMM menu. The N2 protocol assigns key analog parameters to ADF points. The Command Register with override capability is used to reset groups of parameters held in the device.

Before integrating the PMC-53A into a Metasys N2 Network, please make sure that all N2 devices are configured, started and running properly. No more than 32 N2 devices should be connected to an NCM’s N2 Bus segment, and no more than 100 N2 devices when repeaters are used. There are no additional communication setup parameters for the Metasys N2 protocol.

* Default

1) Supported N2 Commands

2) Map Table

89

CET Electric Technology

26

PFb1

72

dPFc

27

PFc1

73

Uan Angle3

°

28

PF Total

74

Ubn Angle3

29

Frequency

Hz

75

Ucn Angle3

30

Neutral Current

(Calculated)

A

76

Ia Angle

31

I4 (Optional Measurement)

A

77

Ib Angle

32

kWh Import

kWh

78

Ic Angle

33

kWh Export

79

Operating Time

h

34

kWh Total

80

Interval kWh Import4

kWh

35

kWh Net

81

Interval kWh Export4

36

kvarh Import

kvarh

82

Interval kvarh Import4

kvarh

37

kvarh Export

83

Interval kvarh Export4

38

kvarh Total

84

Interval kVAh4

kVAh

39

kvarh Net

85

DI #1 Counter

40

kVAh

86

DI #2 Counter

41

kW Total Demand

kW

87

DI #3 Counter

42

kvar Total Demand

kvar

88

DI #4 Counter

43

kVA Total Demand

kVA

89

DI #5 Counter

44

Ia Demand

A

90

DI #6 Counter

45

Ib Demand

91

Clear5

46

Ic Demand

Override Value for Command Register

Action

156001

All Energy values

156002

All Demand values

156003

Reserved

Notes:

1) When the Wiring Mode is 3P3W, the per phase line-to-neutral voltages, kWs, kvars, kVAs and PFs

have no meaning, and their ADF points are reserved.

2) Uan/Ubn/Ucn THD = Uab/Ubc/Uca THD in 3P3W Wiring Mode and represent the harmonics of the

line voltages.

3) Uan/Ubn/Ucn Angle = Uab/Ubc/Uca Angle in 3P3W Wiring Mode and represent the phase angles

of the line voltages.

4) Interval Energy Period (EN Period) can be modified via the Front Panel.

5) The Command register, ADF point 91, is used to reset groups of accumulated values held in the

device. The following table illustrates the override values written to the Command register and their corresponding actions. It is not essential to release the Command Register for the reset to operate. The last Command (156003) is reserved, and the device will respond with 0 if received.

90

CET Electric Technology

DNP V3.0

Vendor Name: CET

Device Name: PMC-53A

Highest DNP Level Supported:

For Requests: Level 1 For Responses: Level 1

Device Function:

 Master  Slave

Notable objects, functions, and/or qualifiers supported in addition to the Highest DNP levels Supported (the complete list is described in the attached table):

Maximum Data Link Frame Size (octets):

Transmitted: 292 Received: 292

Maximum Application Fragment Size (octets):

Transmitted: 1024 Received: 300

Maximum Data Link Re-tries:

 None  Fixed  Configurable

Maximum Application Layer Re-tries:

 None  Configurable

Requires Data Link Layer Confirmation:

 Never  Always  Sometimes  Configurable

Requires Application Layer Confirmation:

 Never  Always  When reporting Event Data (Slave devices only)  When sending multi-fragment responses (Slave devices only)  Sometimes  Configurable

Timeouts while waiting for:

Data Link Confirm:  None  Fixed at ___  Variable  Configurable Complete Appl. Fragment:  None  Fixed at ___  Variable  Configurable Application Confirm:  None  Fixed at ___  Variable  Configurable Complete Appl. Response:  None  Fixed at ___  Variable  Configurable

Others: Transmission Delay, configurable Select/Operate Arm Timeout, fixed at 15 seconds

Sends/Executes Control Operations:

WRITE Binary Outputs  Never  Always  Sometimes  Configurable SELECT/OPERATE  Never  Always  Sometimes  Configurable DIRECT OPERATE  Never  Always  Sometimes  Configurable DIRECT OPERATE - NO ACK  Never  Always  Sometimes  Configurable

Count > 1  Never  Always  Sometimes  Configurable Pulse On:  Never  Always  Sometimes  Configurable Pulse Off:  Never  Always  Sometimes  Configurable Latch On  Never  Always  Sometimes  Configurable Latch Off  Never  Always  Sometimes  Configurable

Queue:  Never  Always  Sometimes  Configurable Clear Queue:  Never  Always  Sometimes  Configurable

Attach explanation if "Sometimes" or "Configurable" was checked for any operation.

Appendix E DNP Profile

This section contains the DNP Device Profile Information according to the standard format defined in the DNP 3.0 Subset Definitions Document and should provide a complete application configuration guide.

91

CET Electric Technology

DNP V3.0

Reports Binary Input Change Events when no specific variation requested:

 Never

 Only time-tagged  Only non-time-tagged  Configurable to send time-tagged or non-time-

tagged

Reports time-tagged Binary Input Change Events when no specific variation requested:

 Never

 Binary Input Change with Time  Binary Input Change with Relative Time  Configurable to send Binary Input Change With

Time and Binary Input Change With Relative Time

Sends Unsolicited Responses:

 Never

 Configurable - enable/disable  Only certain objects  Sometimes (attach explanation)  ENABLE/DISABLE UNSOLICITED Function codes

supported

Sends Static Data in Unsolicited Responses:

 Never

 When Device Restarts  When Status Flags Change

No other options are permitted.

Default Counter Object/Variation:

 No Counters Reported  Configurable  Default Object

Default Variation:

 Point-by-point list attached

Counters Roll Over at:

 No Counters Reported  Configurable  16 Bits  32 Bits  Other Value: ______

 Point-by-point list attached

Sends Multi-Fragment Responses

 Yes  No  Configurable

Sequential File Transfer Support:

Append File Mode  Yes  No Custom Status Code Strings  Yes  No Permissions Field  Yes  No File Events Assigned to Class  Yes  No File Events Send Immediately  Yes  No Multiple Blocks in a Fragment  Yes  No Max. Number of Files Open: 0

OBJECT

REQUEST

(slave must parse)

RESPONSES

(master must parse)

Obj

Var

Description

Func Codes

(dec)

Qual Code

(hex)

Func Codes

(dec)

Qual Code

(hex)

1 2 Binary Input Status with Flag

1

0x06

129

0x00

10 2 Binary Output Status

1

0x06

129

0x00

12 1 Control Relay Output Block

3,4,5

0x28

129

0x28

20 5 32-Bit Binary Counter without Flag

1

0x06

129

0x00

20 6 16-Bit Binary Counter without Flag

1

0x06

129

0x00

30 3 32-Bit Analog Input without Flag

1

0x06

129

0x00

40 2 16-BIT ANALOG OUTPUT STATUS

1

0x06

129

0x00

41 2 16-BIT ANALOG OUTPUT BLOCK

3,4,5

0x28

129

0x28

50 1 Date and Time

1

0x07

129

0x07

60 1 Class 0 Data

1

0x06

129

80 1 Internal Indicator

2

0x00

129

N/A

Cold Restart (respond Obj. 52:2)

13

N/A

129

0x07

Level 1 Implementation (DNP-L1)

92

CET Electric Technology

Function Code

Qualifier Code

Code (dec)

Description

PMC-53A

Code (hex)

Description

PMC-53A

0

Confirm

0x00

8-bit start/stop indices

√

1

Read

√

0x01

16-bit start/stop indices

2

Write

√

0x06

Request for all points

√

3

Select

√

0x07

Single field index, 8-bit format

√

4

Operate

√

0x08

Single field index, 16-bit format

5

Direct Operate With Acknowledge

√

0x17

Control point

6

Direct Operate Without

Acknowledge

0x28

Control point

√

7

Freeze with Acknowledge

8

Immediate Freeze - No

Acknowledge

9

Freeze and Clear with

Acknowledge

10

Freeze and Clear - No

Acknowledge

13

Cold Restart

√

20

Enable Spontaneous Messages

√

21

Disable Spontaneous Messages

√

22

Assign Classes

23

Delay Measurement

129

Solicited Response

√

130

Unsolicited Response

Request

Response

Func.

Code

Description

PMC-53A

Func.

Code

Description

PMC-53A

0

Reset of Remote Link

√ 0 ACK - Positive Acknowledgement

√

1

Reset of User Process

1 NACK - Message Not Accepted, Link Busy

√

2

Test Function for Link

2

Not Used

3

User Data

3

Not Used

4

Unconfirmed User Data

√

4

Not Used

5

Not Used

5

Not Used

6

Not Used

6

Not Used

7

Not Used

7

Not Used

8

Not Used

8

Not Used

9

Request Link Status

√

9

Not Used

10

Not Used

10

Not Used

11

Not Used

11

Status of Link

√

12

Not Used

12

Not Used

13

Cold Restart

√

13

Respond Object 52:2

√

14

Not Used

14

Link Service Not Functioning

15

Not Used

15

Link Service Not Used or Implemented

Port Configuration

Description

Notes

Port Name

COM1

Baud Rate

1200/2400/4800/9600*/19200/38400

Default*

Parity

8E1*/8O1/8N1/8E2/8O2/8N2

Application Layer's Function and Qualifier Code Description

Data Link Layer

The PMC-53A can be assigned a device address between 0 and 65519. After device restart, Function Code 0 (Reset of Remote Link) must be executed to enable DNP communication. The following table describes which Data Link Layer functions are supported.

Physical Layer

The Port 1 RS-485 is designed to support the DNP 3.0 protocol.

93

CET Electric Technology

Point

Description

Format

Range

0

DI11

UINT8

Bit Flags

1

DI21

UINT8

Bit Flags

2

DI31

UINT8

Bit Flags

3

DI41

UINT8

Bit Flags

4

DI5

1,2

UINT8

Bit Flags

5

DI6

1,2

UINT8

Bit Flags

Point

Description

Format

Range

0

Clear Present Energy Log

UINT8

Always 0

1

Clear All Energy Registers

UINT8

Always 0

2

Clear Present Monthly Energy Log

UINT8

Always 0

3

Clear Peak Demand of This Month (Since Last Reset)

UINT8

Always 0

4

Clear All Demand Registers

UINT8

Always 0

5

Clear Max/Min Logs of This Month (Since Last Reset)

UINT8

Always 0

6

Clear All Max./Min. Log

UINT8

Always 0

7

Clear Device Operating Time

UINT8

Always 0

8

Clear All Data

UINT8

Always 0

9

Clear DI1 Pulse Counter

UINT8

Always 0

10

Clear DI2 Pulse Counter

UINT8

Always 0

11

Clear DI3 Pulse Counter

UINT8

Always 0

12

Clear DI4 Pulse Counter

UINT8

Always 0

13

Clear DI5 Pulse Counter

UINT8

Always 0

14

Clear DI6 Pulse Counter

UINT8

Always 0

15

Clear All Pulse Counters

UINT8

Always 0

16

DO11

UINT8

Bit Flags

17

DO21

UINT8

Bit Flags

18

DO3

1,2

UINT8

Bit Flags

19

DO4

1,2

UINT8

Bit Flags

20-29

Reserved

30-43

Wiring Diagnostics Status

UINT8

Bit Flags

No.

Event

30

Frequency is out of range (45 to 65Hz) (3P4W or 3P3W)

31

Any phase voltage < 10% of PT Primary (Register 6000) (3P4W only)

32

Any phase current < 10% of CT Primary (Register 6004) (3P4W or 3P3W)

33

RTD 1 broken (RTD Input option only)

34

RTD 2 broken (RTD Input option only)

…

Voltage Phase Reversal (3P4W only)

Current Phase Reversal (3P4W or 3P3W)

Negative kW Total may be abnormal (3P4W or 3P3W)

Negative kWa is may be abnormal (3P4W only)

Negative kWb may be abnormal (3P4W only)

Negative kWc may be abnormal (3P4W only)

CTa polarity may be reversed (3P4W only)

CTb polarity may be reversed (3P4W only)

DNP Point Map

Object 1 - Binary Input Status with Flags (Included in Class 0 responses)

Read with Object 1, Variation 2, and Qualifier 6.

Supported Flags: Bit 0 (ONLINE): 0=Offline, 1=Online

Bit 7 (STATE): 0=Off, 1=On

Notes:

1) If the Device Model does not support DI, the Bit 0 and Bit 7 for the bytes of all DI status above would be set to “0”.

2) If 4xDIs are supported on the Device Model, the Bit 0 and Bit 7 in bytes for DI5 and DI6 status would be set to “0”.

Object 10 - Binary Output States (Included in Class 0 responses)

Read with Object 10, Variation 2, and Qualifier 6.

Notes:

1) If the Device Model does not support DO, the Bit 0 and Bit 7 for the bytes of all DO status above would be set to “0”.

2) If 2xDOs are supported on the Device Model, the Bit 0 and Bit 7 in bytes for DO3 and DO4 status would be set to “0”.

3) The following table shows the details of Point 30-43.

94

CET Electric Technology

43

CTc polarity may be reversed (3P4W only)

Point

Description

Format

Range

0

Clear Present Energy Log

UINT8

N/A

1

Clear All Energy Registers

UINT8

N/A 2 Clear Present Monthly Energy Log

UINT8

N/A 3 Clear Peak Demand of This Month (Since Last Reset)

UINT8

N/A

4

Clear All Demand Registers

UINT8

N/A

5

Clear Max/Min Logs of This Month (Since Last Reset)

UINT8

N/A

6

Clear All Max./Min. Log

UINT8

N/A

7

Clear Device Operating Time

UINT8

N/A

8

Clear All Data

UINT8

N/A

9

Clear DI1 Pulse Counter

UINT8

N/A

10

Clear DI2 Pulse Counter

UINT8

N/A

11

Clear DI3 Pulse Counter

UINT8

N/A

12

Clear DI4 Pulse Counter

UINT8

N/A

13

Clear DI5 Pulse Counter

UINT8

N/A

14

Clear DI6 Pulse Counter

UINT8

N/A

15

Clear All Pulse Counters

UINT8

N/A

16

DO1

UINT8

Bit Flags

17

DO2

UINT8

Bit Flags

18

DO3

UINT8

Bit Flags

19

DO4

UINT8

Bit Flags

Point

Description

Format

Unit

Scale

Range

0

kWh Import

INT32

kWh

10

0-999,999,999

1

kWh Export

INT32

kWh

2

kWh Net

INT32

kWh

3

kWh Total

INT32

kWh

4

kvarh Import

INT32

kvarh

5

kvarh Export

INT32

kvarh

6

kvarh Net

INT32

kvarh

7

kvarh Total

INT32

kvarh

8

kVAh

INT32

kVAh

9

kvarh Q1

INT32

kvarh

10

kvarh Q2

INT32

kvarh

11

kvarh Q3

INT32

kvarh

12

kvarh Q4

INT32

kvarh

13

Interval kWh Import

INT32

kWh

14

Interval kWh Export

INT32

kWh

15

Interval kvarh Import

INT32

kvarh

16

Interval kvarh Export

INT32

kvarh

17

Interval kVAh

INT32

kVAh

18

DI1 Pulse Counter

1

UINT32

1

0-999,999,999

19

DI2 Pulse Counter1

UINT32

1

20

DI3 Pulse Counter1

UINT32

1

21

DI4 Pulse Counter1

UINT32

1

Supported Flags: Bit 0 (ONLINE):

0 = Offline, which represents that the control of the Output could not be implemented. 1 = Online, which represents that the Output works properly, once control request has been sent, the command could be

correctly implemented.

Bit 7 (STATE): 0=Off, 1=On

Object 12 - Control Relay Outputs

Responds to Function Codes: 03 (Select), 04 (Operate) and 05 (Direct Operate), Variation 1, Qualifier 0x28, with a Count of 1 only. Only one control object at a time may be specified.

Please refer to the DNP V3.00 Data Object Library document for a detailed description of the Object Coding format for the Control Relay Output Block as well as the meanings of the returned Status.

Object 20 - 32-BIT Binary Counters - Primary Readings (Included in Class 0 responses)

Read with Object 20, Variation 5, and Qualifier 6.

95

CET Electric Technology

22

DI5 Pulse Counter

1,2

UINT32

1

23

DI6 Pulse Counter

1,2

UINT32

1

Point

Description

Format

Range 0 Scale for Energy and Operating Time

UINT16

10 1 Scale for Current, PF, I Seq., I Fund., and I Demand

UINT16

1000

2

Scale for U, Freq, Phase Angle, RTD, U Fund., U Seq.,

THD, TDD, K Factor, Crest-factor and Unbalance

UINT16

100

3

Scale for AI, AO, Power and Power Demand

UINT16

1

4

Firmware Version1

UINT16

0-65535

5

Feature Code2

UINT16

0-65535

Bit 7 to Bit 8 (Basic I/O Function)

Bit 3 to Bit 5 (Expansion Module B)

Bit 0 to Bit 2 (Expansion Module A)

00=4xDI+2xDO 01=None 10=4xDI+2xSS Pulse Output

000=None 001=1xAI + 1xAO 010=2xDI + 2xDO 011=2xRTD 100=2xDI + 2x SS Pulse Output 101=Reserved

000=None 001=RS485 010=I4 011=SPI

Point

Description

Format

Scale

Unit

0

Meter Health

INT32

Always 0

-

1

Uan

INT32

x100

V

2

Ubn1

INT32

3

Ucn1

INT32

4

Uln Average

INT32

5

Uab

INT32

6

Ubc

INT32

7

Uca

INT32

8

Ull Average

INT32

9

Ia

INT32

x1000

A

10

Ib1

INT32

11

Ic1

INT32

12

I average

INT32

13

kWa

INT32

x1

W

14

kWb1

INT32

15

kWc1

INT32

16

kW Total

INT32

17

kvara

INT32

var

18

kvarb1

INT32

19

kvarc1

INT32

20

kvar Total

INT32

21

kVAa

INT32

VA 22

kVAb1

INT32

23

kVAc1

INT32

24

kVA Total

INT32

25

P.F.a

INT32

x1000

-

26

P.F.b1

INT32

27

P.F.c1

INT32

28

P.F. Total

INT32

29

FREQ

INT32

x100

Hz

30

Uan/Uab (3P3W) Angle

INT32

x100

°

Notes:

1) If the Device Model does not support DI, all DI Pulse Counters would be set to “0”.

2) If 4xDIs are supported on the Device Model, DI5 and DI6 Pulse Counter would be set to “0”.

Object 20 - 16-BIT Binary Counters - Primary Readings (Included in Class 0 responses)

Read with Object 20, Variation 6, and Qualifier 6.

Notes:

1) The read-out value 10000 represents the Version is V1.00.00.

2) The following table illustrates the details of Feature Code. Bit 6 and Bit 9 to Bit 15 for the Byte are reserved. Points for I4,

AI Scaled, RTD1, RTD2 and AO in Object 30 are only meaningful if the meter is equipped with the corresponding option.

Object 30 - Analog Inputs Primary Readings (Included in Class 0 responses) Read with Object 30, Variation 3, and Qualifier 6.

96

CET Electric Technology

31

Ubn/Ubc (3P3W) Angle

INT32

32

Ucn/Uca (3P3W) Angle

INT32

33

Ia Angle

INT32

34

Ib Angle

INT32

35

Ic Angle

INT32

36

In (Calculated)

INT32

x1000

A

37

I4

INT32

38

Ir

INT32

39

Displacement PFa

INT32

x1000

-

40

Displacement PFb1

INT32

41

Displacement PFc1

INT32

42

Displacement PF Total

INT32

43

AI Scaled

INT32

x1

-

44

RTD 1

INT32

x100

︒C

45

RTD 2

INT32

46

AO

INT32

x1

-

47

Device Operating Time

INT32

x10

h

48

Phase A Fundamental kW

INT32

x1

W

49

Phase B Fundamental kW1

INT32

50

Phase C Fundamental kW1

INT32

51

Fundamental kW Total

INT32

52

Total Harmonic kW

INT32

53

Uan/Uab Fundamental

INT32

x100

V

54

Ubn/Ubc Fundamental

INT32

55

Ucn/Uca Fundamental

INT32

56

Ia Fundamental

INT32

x1000

A

57

Ib Fundamental1

INT32

58

Ic Fundamental1

INT32

59

U1 (+ve Sequence Voltage)2

INT32

x100

V

60

U2 (-ve Sequence Voltage)2

INT32

61

U0 (Zero Sequence Voltage)2

INT32

62

I1 (+ve Sequence Current)2

INT32

x1000

A

63

I2 (-ve Sequence Current)2

INT32

64

I0 (Zero Sequence Current)2

INT32

65

Ia TDD

INT32

x100

-

66

Ib TDD

INT32

67

Ic TDD

INT32

68

Ia K Factor

INT32

69

Ib K Factor

INT32

70

Ic K Factor

INT32

71

Ia Crest-factor

INT32

72

Ib Crest-factor

INT32

73

Ic Crest-factor

INT32

74

Voltage Unbalance

INT32

75

Current Unbalance

INT32

76

Uan/Uab THD

INT32

77

Ubn/Ubc THD

INT32

78

Ucn/Uca THD

INT32

79

Ia THD

INT32

80

Ib THD

INT32

81

Ic THD

INT32

82

Ia Present Demand

INT32

x1000

A

83

Ib Present Demand

INT32

84

Ic Present Demand

INT32

85

∑kW Present Demand

INT32

x1

W

86

∑kvar Present Demand

INT32

var

87

∑kVA Present Demand

INT32

VA

88

Ia Peak Demand of This Month (Since Last Reset)

INT32

x1000

A

89

Ib Peak Demand of This Month (Since Last Reset)

INT32

90

Ic Peak Demand of This Month (Since Last Reset)

INT32

91

∑kW Peak Demand of This Month (Since Last Reset)

INT32

x1

W

92

∑kvar Peak Demand of This Month (Since Last Reset)

INT32

var

93

∑kVA Peak Demand of This Month (Since Last Reset)

INT32

VA

94

Ia Peak Demand of Last Month (Before Last Reset)

INT32

x1000

A

95

Ib Peak Demand of Last Month (Before Last Reset)

INT32

96

Ic Peak Demand of Last Month (Before Last Reset)

INT32

97

CET Electric Technology

97

∑kW Peak Demand of Last Month (Before Last Reset)

INT32

x1

W

98

∑kvar Peak Demand of Last Month (Before Last Reset)

INT32

var

99

∑kVA Peak Demand of Last Month (Before Last Reset)

INT32

VA

Point

Property

Description

Format

Range

0

RO

Class 0 Points

UINT16

0-65535

Point

Property

Description

Format

Range

0

WO

Class 0 Points

UINT16

0-65535

Bit Point

Descriptions

Value

Bit 0

Object 1 - Binary Input Status Included in Class 0 responses?

0=No, 1=Yes (default)

Bit 1

Object 10 - Binary Output States Included in Class 0 responses?

0=No, 1=Yes (default)

Bit 2

Object 20 - 32 BIT Binary Counters Included in Class 0 responses?

0=No, 1=Yes (default)

Bit 3

Object 20 - 16 BIT Binary Counters Included in Class 0 responses?

0=No, 1=Yes (default)

Bit 4

Object 30 -Analog Inputs Included in Class 0 responses?

0=No, 1=Yes (default)

Bit 5

Object 40 - Analog Output Status Included in Class 0 responses?

0=No, 1=Yes (default)

Bit 6- Bit 15

Reserved

Point

Description

Format

Range

7

Device Restart

UINT8

0-1

Notes:

1) When the Wiring Mode is 1P2W L-N or 1P2W L-L, the L2 and L3 phase voltages and currents have no meaning, and their

registers are reserved.

2) When the Wiring Mode is 1P2W L-N, 1P2W L-L or 1P3W, the Sequence Components U1/I1, U2/I2 and U0/I0 have no

meaning and their registers are reserved.

Object 40 - Analog Output Status Objects

Read with Object 40, Variation 2, and Qualifier 6.

Object 41 - Analog Output Command Objects

Responds to Function Codes: 03 (Select), 04 (Operate) and 05 (Direct Operate), Variation 2, Qualifier 0x28, with a Count of 1 only.

Note: The following table illustrates the details of Bit Values for Class 0 Points.

Object 50 - Date and Time

Read and Write function is supported for this object, which occupies 6 bytes for the device's time. The time shows the number of UNIX milliseconds since 00:00:00 January 1, 1970, calculated by UNIX seconds*1000 + milliseconds.

Object 60 - Class Objects

Read with Function Code 1, Variation 1, and Qualifier 6. Only Class 0 polls are supported.

Object 80 - Internal Indicator

This is a Write Only function. Clear the Restart Bit with Function Code 2, Variation 1, Qualifier 0.

98

CET Electric Technology

Voltage Inputs (V1, V2, V3, VN)

Standard Un Range Overload Burden Measurement Category

400VLN/690VLL 10V to 1.2Un

1.2xUn continuous, 2xUn for 1s <0.02VA per phase CAT III up to 600VLL

Frequency

45-65Hz

Current Inputs (I11, I12, I21, I22, I31, I32)

Standard In=5A/1A Auto-scale Optional In=1A Range Starting Current Overload Measurement Category Burden

Class 0.5S for 5A and Class 1 for 1A Class 0.5S

0.1% to 200% In

0.1% In 2xIn continuous, 20xIn for 1s CAT III up to 600VLL <0.15VA per phase

Optional I4 Input (I41, I42)

In Range Starting Current

5A (5A/1A Auto-Scale)

0.1% to 120% In

0.1% In

Power Supply (L+, N-, GND)

Standard Optional Optional Burden Overvoltage Category

95-250VAC/DC, ±10%, 47-440Hz 20-60VDC 95-480VAC/DC, ±10%, 47-440Hz <2W CAT III up to 300VLN

Digital Inputs (DI1, DI2, DI3, DI4, DIC)

Type Sampling Hysteresis

Dry contact, 24VDC internally wetted 1000Hz 1ms minimum

Digital Outputs (DO11, DO12, DO21, DO22)

Type Loading

Form A Mechanical Relay 5A @ 250VAC or 30VDC

Pulse Outputs (kWh, kvarh)

Type Isolation Max. Load Voltage Max. Forward Current

Form A Solid State Relay Optical 80V 50mA

Installation Torque

Current Inputs

1.3 N.m

Power Supply, Voltage Inputs, RS485 and I/O

0.5 N.m

Environmental Conditions

Operating Temp. Storage Temp. Humidity Atmospheric Pressure

-25°C to 70°C

-40°C to 85°C 5% to 95% non-condensing 70 kPa to 106 kPa

Mechanical Characteristics

Panel Cutout Unit Dimensions IP Rating

92x92 mm (3.62”x3.62”) 96x96x88 mm 65

Appendix F Technical Specifications

99

Accuracy

Parameters

Accuracy

Resolution

Voltage

±0.2% Reading + 0.05% F.S.

0.001V

Current

±0.2% Reading + 0.05% F.S.

0.001A

I4 (measurement)

±0.2%

0.001A

kW, kvar, kVA

±0.5% Reading + 0.05% F.S.

0.001k

kWh, kVAh

IEC 62053-22 Class 0.5S

0.1kXh

kvarh

IEC 62053-23 Class 2

0.1kvarh

P.F.

±0.5%

0.001

Frequency

±0.02 Hz

0.01Hz

THD

IEC 61000-4-7 Class B

0.001%

K-Factor

IEC 61000-4-7 Class B

0.001

Phase angles

±1°

0.1°

CET Electric Technology

100

CET PMC-53A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual