How it Works
CESeasy
Loading...
#
Loading...
Loading...
347100V
Assembly And Operating Manual
53 pgs1.13 Mb0
Table of contents
Loading...

CESeasy 347100V Assembly And Operating Manual

Download
CESeasy
Motor cylinder
Assembly and Operating Manual
Manual for dealers and service technicians
English
Version VC
BRO2275-2
Contents
1.1 Design characteristics 4
1.2 Target group of this manual 4
2.1 Manufacturer and service 5
2.2 Manufacturer’s warranty 5
3.1 EU Declaration of conformity 6
3.2 Intended use 6
3.3 Basic safety instructions 6
3.4 Notes on dealing with batteries 7
4.1 About CESeasy motor cylinders 9
4.2 Scope of application 9
4.3 Notes about burglary protection 9
5.1 Before ordering: Check cylinder length 10
5.2 Assembly of a mechanical cylinder 11
5.3 Disassembly of the mechanical cylinder 15
7.1 Disassembly of the existing cylinder 19
7.2 Assembly of the CESeasy motor cylinder 20
8.1 Required batteries 23
8.2 Battery consumption 23
8.3 Battery warnings 23
Page 2 of 53 CESeasy motor cylinder
8.4 How to insert and change batteries 24
8.5 Battery disposal 26
9.1 CESeasy app 27
9.2 Coupling 28
9.3 Configuration menu 31
10.1 Automatic firmware updates 34
10.2 Manual firmware updates 34
11.1 CESeasy web platform 35
11.2 Extension functions 35
12.1 How to use it with the rotary knob 38
12.2 Operation with a mechanical key 39
12.3 How to use it with a remote control 39
12.4 Operation via smartphone 39
13.1 Equipment features 41
13.2 Dimensions 42
14.1 Door contact 43
14.2 Power supply unit for external power supply 46
15.1 Notes on disposal 48
CESeasy motor cylinder Page 3 of 53
1 About this manual

1 About this manual

These assembly and operating instructions, hereinafter referred to as the “manual”, will help you
with the assembly and in a proper, safe, and beneficial use of the CESeasy products acquired.
Anyone who assembles, administers, maintains, or disposes of CESeasy products, must have read
and understood the complete contents of this manual.
If you do not understand the functions of the CESeasy products, please contact your CES partner
for further information.
Always use the latest version of this manual. The version number of this manual is shown
on the cover page. You can get the latest version free of charge from www.ces.eu

1.1 Design characteristics

Refers to other documents.
Marks additional information and tips.
Marks warnings in step-by-step instructions and specially important information.

1.2 Target group of this manual

This manual is intended for
l Trained service and assembly personnel
l Maintenance personnel
l Operators
The necessary expertise regarding the intended use of the product is presumed for the use of this
manual.
The necessary product training is conducted by your CES partner. If this has not yet taken place,
please contact your CES partner to get the product training.
Page 4 of 53 CESeasy motor cylinder

2 Manufacturer’s information

2.1 Manufacturer and service

C.Ed. Schulte GmbH
Zylinderschlossfabrik
Friedrichstr. 243
42551 Velbert
Tel: +49 (0) 2051-204-0
Fax: +49 (0) 2051-204-229
www.ces.eu

2.2 Manufacturer’s warranty

The following damage is not covered by the manufacturer’s warranty:
2 Manufacturer’s information
l Damage to the exterior mechanical parts as well as subsequent damage arising from nor-
mal wear and tear.
l Damage caused by external events or influences
l Damage caused by deficient assembly
l Damage caused by deficient maintenance
l Damage caused by false operation
l Damage caused by overvoltage
l Damage caused by fire, water or smoke
All technical data and features are subject to change without prior notice. All information and
data contained in this document is subject to change without prior notice. Without express
written approval from C.Ed. Schulte GmbH Zylinderschlossfabrik, no part of this document may be
copied or transmitted for any purposes whatsoever.
© 2018 C.Ed. Schulte GmbH Zylinderschlossfabrik, Velbert/Germany
VC
BRO2275-2
CESeasy motor cylinder Page 5 of 53
3 For your safety

3 For your safety

3.1 EU Declaration of conformity

You can find the EU Declaration of conformity on the Internet at www.ces.eu.

3.2 Intended use

CESeasy products are intended to control access at doors. They are exclusively intended for this
purpose and may only be used for this. They may never be altered in any way without written
permission from C.Ed. Schulte GmbH Zylinderschlossfabrik.
All other uses are regarded as improper use and may lead to material damage or even personal
injuries. C.Ed. Schulte GmbH Zylinderschlossfabrik assumes no liability for damage caused by
improper use.

3.3 Basic safety instructions

CESeasy products have been built with state-of-the-art technology and established safety
regulations. Nevertheless, their use may constitute function-related hazards for the user or third
parties and may impair the handle set and other material assets.
Please observe all warnings and notices in this manual while assembling, configuring and using
CESeasy products.
3.3.1 Life-threatening danger
l CESeasy products have not been developed, tested and/or approved for access in
life-threatening situations. Do not use CESeasy products on fire doors or panic doors.
l CESeasy products must be suitable for your door system. If you are in doubt, please contact
the manufacturer of the door or lock to check suitability.
l All components which are required for a complete installation at your door must be CE-
compliant. Please check before installation whether all components used are CE-compliant.
3.3.2 Danger of personal injury
Danger of explosion
l Live parts may cause explosion. Do not use parts in potentially explosive areas.
Page 6 of 53 CESeasy motor cylinder
3.3.3 Danger of damage to material assets
Transportation
l Do not drop the device on the floor, on hard surfaces or objects.
Assembly
l The device contains highly sensitive electronic components, which can be damaged or
destroyed through electrostatic charges. Therefore, do not assemble the handle set in
areas affected by electrostatic charge.
l For assembly and dismantling, use the tools indicated in the "Assembly" section only.
l Only use a dry or protected or indoors place for device installation.
Operation
l Protect the electronic components against water and other fluids.
3 For your safety
Maintenance
l Always have repairs performed by qualified personnel.
l Use only the accessories and spare parts recommended by CES.
Danger through climatic influences
l Do not use the device in corrosive atmosphere (chlorine, ammonia, lime water)
l Do not use the device in areas with high dust formation.
l Do not use the device near heat sources.
Please observe the maximum permissible temperatures and the information on air humidity in
the section “Technical Data".

3.4 Notes on dealing with batteries

l Always insert new batteries only. Never use old and new batteries together.
l Before inserting the batteries, check whether the contacts in the device and on the bat-
teries are clean. Otherwise, clean them. Do not touch the contacts after the cleaning pro-
cess.
l When inserting the batteries, ensure that the polarity is correct (+/-).
l Never try to recharge the batteries. There is a risk of explosion!
l Do not short-circuit the batteries.
l Store batteries in a cool and dry place. Direct heat may damage the batteries. Therefore, do
not expose battery-operated devices to any strong heat source, and do not throw the bat-
teries into fire.
CESeasy motor cylinder Page 7 of 53
3 For your safety
l If you do not use devices for a longer time, take out the batteries.
l Remove leaking batteries immediately from the device. Clean the contacts before inserting
new batteries. There is danger of injury from battery acid.
l Remove the empty batteries from the device.
l Please take note of the information on battery disposal (see "Disposal" on page48).
Page 8 of 53 CESeasy motor cylinder
4 About CESeasy motor cylinders

4 About CESeasy motor cylinders

4.1 About CESeasy motor cylinders

The CESeasy motor cylinder has been developed to grant access in a comfortable way. At the
same time, the smartphone or remote control are the keys. The digital keys required for this kind
of access are easily managed on the CESeasy web platform.

4.2 Scope of application

The CESeasy motor cylinder is suitable for doors with a lock with euro profile cylinders below the
handle set.
CESeasy products have not been developed, tested and/or approved for access to escape
and emergency routes. Do not use CESeasy products on fire doors or panic doors.

4.3 Notes about burglary protection

l Use CESeasy products with break-in resistance together with a handle set.
l To maintain the break-in resistance of a cylinder, it must never project more then 3 mm
beyond the surface of the handle set. Make sure to use the correct cylinder length for
your handle set.
CESeasy motor cylinder Page 9 of 53
5 Mechanical cylinder for the motor cylinder

5 Mechanical cylinder for the motor cylinder

5.1 Before ordering: Check cylinder length

Before a CESeasy motor cylinder is ordered, the length of the mechanical cylinder has to be
checked.
Tools required:
Folding rule or calliper gauge
How to proceed:
1. Determine the dimensions for the outside (S) and the
inside (K) of the cylinder.
Outside (S): Measure from the middle of the
cylinder fixing screw (3) to the end of the outside
fitting (1).
Inside (S): Measure from the middle of the cylinder
fixing screw (3) to the end of the inside fitting (2).
2. Indicate the exact dimensions for the exterior and the
interior together with your order.
From the measurements indicated, CES determines the
mechanical cylinder which matches your motor cylinder.
You will receive the motor cylinder with a pre-assembled
mechanical cylinder.
To maintain the break-in resistance of a cylinder, it must never project more then 3 mm
beyond the surface of the handle set. Make sure to use the correct cylinder length for
your handle set.
Page 10 of 53 CESeasy motor cylinder
5 Mechanical cylinder for the motor cylinder

5.2 Assembly of a mechanical cylinder

Suitable cylinders
Please use the motor cylinder only with cylinders which are approved for use with the
CESeasy motor units. Amongst other tests, approved cylinders have to undergo an
extensive endurance test to ascertain whether the cylinder withstands the force exerted
by the motor cylinder.
In order to offer break-in resistance, CESeasy motor units may only be combined with
cylinders which have been pointed out as suitable by CES.
Tools required
Tool e.g. by
MC2 torque wrench Proxxon Industrial MicroClick
2.0x50 Allen key Wera 840/4 Z (05059603001)
TORX Bit TX10x25 Wera-TORX-Bit, 867/1 Z (05066485001)
Assembly aid (optional) Available at CES on request
CESeasy motor cylinder Page 11 of 53
Assembly
5 Mechanical cylinder for the motor cylinder
1. Remove all possibly inserted batteries from the motor
unit (see "How to insert and change batteries" on
page24).
2. Loosen and remove the four TORX screws which
attach the assembly plate to the case.
3. Remove the assembly plate from the case of the
motor unit.
4. Remove the black plastic bearing ring from the
connecting sleeve.
5. Remove the driver pin (3 x 20 mm) from the
connecting sleeve.
Page 12 of 53 CESeasy motor cylinder
5 Mechanical cylinder for the motor cylinder
6. Put the assembly plate with its recesses for the
7. Put the cylinder with the shaft first into the assembly
screws face-up into the assembly aid.
plate.
Make sure that the cylinder aligns with the
assembly plate. To do so, you can use the optionally
available assembly aid, or you can place the cylinder
together with the mounting plate e.g. onto the
edge of a table.
8. First, tighten
one side of the assembly plate. Then tighten the two
screws on the other side with 2 Nm. Then, also
tighten the screws on the first side with 2 Nm.
9. Put the plastic bearing ring onto the cylinder shaft.
The hole of the ring has to match the shaft
diameter of the cylinder. If the bearing ring does not
fit around the shaft, or if there is a certain
clearance, please contact your supplier.
gently
the two socket head screws on
10. Press the driver pin through the hole in the shaft
and hold on to it so that it cannot slip out of the hole.
CESeasy motor cylinder Page 13 of 53
5 Mechanical cylinder for the motor cylinder
11. Put the assembly plate with the cylinder shaft first
into the connecting sleeve. The cylinder shaft needs
to be aligned in such a way that the driver pin fits
into the recess of the connecting sleeve. To align the
shaft, please turn the locking cam of the cylinder.
12. Insert the four TORX screws in the case. Then gently
tighten all screws. In a second step, tighten all four
screws with 1 Nm.
Please make sure that the screws do not cut a new
thread into the screw holes. This could damage the
case. To make sure that the screws will engage
with the already existing thread, turn them anti-
clockwise until you can hear them falling into place
in the thread. Then tighten them carefully.
13. Check the cylinder functions by turning the knob of
the motor unit.
14. Check the cylinder functions by turning the cylinder
with the key.
Because of the special coupling of the mechanical
cylinder, the knob does not turn with the cylinder if
you use a mechanical key to turn the cylinder.
However, if the knob of the motor unit does turn
with the cylinder, please contact the CES service.
If the cylinder works correctly, you can mount the CESeasy
motor cylinder to the door.
Page 14 of 53 CESeasy motor cylinder
5 Mechanical cylinder for the motor cylinder

5.3 Disassembly of the mechanical cylinder

Tools required
Tool e.g. by
MC2 torque wrench Proxxon Industrial MicroClick
2.0x50 Allen key Wera 840/4 Z (05059603001)
TORX Bit TX10x25 Wera-TORX-Bit, 867/1 Z (05066485001)
Disassembly
1. Remove any possibly existing batteries from the
motor cylinder (see "How to insert and change
batteries" on page24).
2. Loosen and remove the four TORX screws which
attach the assembly plate to the case.
3. Remove the cylinder with the assembly plate from
the case of the motor unit.
CESeasy motor cylinder Page 15 of 53
5 Mechanical cylinder for the motor cylinder
4. Remove the driver pin and the ring.
5. Loosen the four socket head screws on one side of the
assembly plate and remove the cylinder from the
assembly plate.
6. To mount the new cylinder, please proceed according
to the assembly instructions from step 6.
Page 16 of 53 CESeasy motor cylinder
6 Scope of delivery

6 Scope of delivery

1 1 CESeasy motor cylinder (CESeasy motor unit with mounted mechanical cylinder)
2 1 Key
3 1 Cylinder fixing screw
4 1 Registration card (incl. extension function “Lock management, see "Extension functions" on
page35)
5 1 Remote control (only part of the starter set)
6 6 Batteries
Registration card
You will find important information on the registration card about your device, including the
registration code. You need it to create a lock owner account or to add your device to the already
existing lock owner account.
The registration card contains the following information:
CESeasy motor cylinder Page 17 of 53
6 Scope of delivery
Registration address
The URL you can use to create a lock owner account.
S/N
Serial number of the device. It must coincide with the serial number
on your device:
For motor cylinders: Serial number on the sticker in the battery
compartment and on the back of the motor cylinder.
For door controllers: Serial number on the sticker in the casing
beneath the battery compartment and on the back of the door
controller.
Bluetooth MAC address
The unique Bluetooth MAC address of the device.
Registration code
You need this code to register your device in your lock owner
account. If you do not have a lock owner account yet, you need the
registration code to create your lock owner account.
Keep your registration card in a safe place. You will need it in a service situation, or if you
want to transfer the lock to another lock owner account.
Page 18 of 53 CESeasy motor cylinder
7 Assembly

7 Assembly

It is recommended to have CESeasy products installed and configured by CES partners.
They are not only familiar with the products, but rather also with your door. Therefore,
they can guarantee that the devices work correctly.

7.1 Disassembly of the existing cylinder

To be able to remove the cylinder, it may sometimes be necessary to slightly loosen the
screws of the existing handle set.
Tools required:
The required tool depends on the cylinder fixing screw of the existing cylinder.
Disassembly of the existing cylinder
1. Loosen the cylinder fixing screw of the existing
cylinder.
2. Remove the existing cylinder.
Use the key to turn the locking cam of the existing
cylinder so that the cylinder can be removed from
the door.
CESeasy motor cylinder Page 19 of 53

7.2 Assembly of the CESeasy motor cylinder

Tools required
Tool Required for
7 Assembly
PZ2
Phillips screwdriver
Smartphone with CESeasy app
Smartphone prerequisites:
l iOS (iOS 9.2 or higher) or Android (Android
4.4 or higher)
l If you use an iPhone: iPhone 4S or
newer models
l Bluetooth 4.0 or higher
l suitable for Bluetooth Low Energy
Cylinder fixing screw
Configuration and test of the motor
cylinder
Page 20 of 53 CESeasy motor cylinder
7 Assembly
Assembly of the CESeasy motor cylinder
1. Remove all possibly existing batteries from the motor
cylinder.
2. Fix the existing handle set tightly enough to insert the
cylinder with ease in the door.
This step is necessary because after having attached
the motor cylinder, it will no longer be possible to
fasten the handle set.
3. Use the knob of the motor cylinder to turn the locking
cam far enough so as not to be an obstacle.
4. Push the cylinder into the door.
5. Tighten the cylinder fixing screw by hand. Do not use a
cordless screwdriver or similar tools.
If you fasten the cylinder fixing screw too strongly
the service life of the cylinder may be reduced!
Please also follow any assembly instructions given by
the manufacturer of the cylinder which is attached
to the motor cylinder.
6. Insert the batteries.
Please also refer to chapter "Batteries" on page23.
7. Check that the motor cylinder works correctly with
the
opendoor
- Turn the knob of the motor cylinder manually.
- Use a key for the mechanical cylinder.
CESeasy motor cylinder Page 21 of 53
:
7 Assembly
8. Carry out a firmware update. To do so, connect the
motor cylinder with the CESeasy app (see "Coupling" on
page28), and click on UPDATE.
9. Configure the motor cylinder (see "Configuration" on
page27).
10. Check that the motor cylinder works correctly with
the CESeasy app with
theopen door
.
11. Check that the motor cylinder works correctly with
the CESeasy app with the closed door.
Now the motor cylinder is ready.
Troubleshooting
To check whether the motor cylinder works correctly, check every solution described above first
with an open door and then with a closed door.
Problem
The motor cylinder does not lock
or unlock correctly
Solution
1. Adjust the door correctly.
2. Check whether the locking plates are installed correctly.
3. Ask a service technician to adapt the parameters in the
expert settings of the configuration menu.
Page 22 of 53 CESeasy motor cylinder
8 Batteries

8 Batteries

8.1 Required batteries

You need six AA alkaline batteries.

8.2 Battery consumption

Battery consumption of the motor cylinder depends, amongst others, on the following factors:
l Quality and capacity of the batteries. The higher the capacity, the longer the batteries will
last.
l The time the motor cylinder requires to turn the lock in order to lock or unlock the door.
The longer the motor cylinder is in operation, the quicker the batteries run down.
l The force the motor cylinder has to apply. If, for example, the door is warped, the motor cyl-
inder has to apply a higher force, and the batteries run down more quickly.
l Ambient temperature. If ambient temperatures are lower, battery service life will be
reduced.
l The “Automatic closure” function: If this function is used, the motor cylinder automatically
locks the door after it has been closed (requires a door contact). This function runs down
the batteries more quickly.
l The opening times set, i.e. the period during which the latchbolt is retrieved and kept in its
position by the motor cylinder. Prolonged opening times reduce battery life.

8.3 Battery warnings

Battery warning emitted by the motor cylinder
If the batteries are nearly empty, the device emits the usual acoustic signal after an opening or
closing operation, and then three acoustic battery warning signals (--- --- ---).
The battery warning signals are also emitted if you have switched off the normal acoustic
signal via the configuration settings.
Battery warning in the CESeasy app
If the batteries are nearly empty, a pop-up window opens in the CESeasy app after an opening or
closing operation which informs you about the battery status.
CESeasy motor cylinder Page 23 of 53
8 Batteries
If the battery warning shows that the batteries are nearly empty, the door controller will continue
to work for some more time. However, the duration of this period depends strongly on the
aspects mentioned in the section "Battery consumption" on the previous page.

8.4 How to insert and change batteries

Please refer to chapter "Disposal" on page48 when changing the batteries.
Tools required:
You can manually remove the design screw of the battery compartment. If the design screw is
too tight, you can loosen it with an Allen key (4mm).
If you want to prevent that the battery compartment can be manually opened, you can
replace the design screw by a safety screw (M4 thread, length 8mm).
Page 24 of 53 CESeasy motor cylinder
8 Batteries
How to insert and change batteries
1. Loosen the design screw.
2. Slide the cover of the battery compartment
downwards and remove it.
3. If necessary, take out the six empty batteries.
4. Insert the six new batteries.
Please ensure that the batteries are inserted
according to the labelling in the battery
compartment which indicates the correct polarity.
CESeasy motor cylinder Page 25 of 53
8 Batteries
5. Slide the cover back onto the battery compartment.
6. Tighten the design screw by hand.
The batteries are now inserted or have been changed.

8.5 Battery disposal

See "Disposal" on page48.
Page 26 of 53 CESeasy motor cylinder
9 Configuration

9 Configuration

It is recommended to have CESeasy products installed and configured by CES partners.
They are not only familiar with the products, but rather also with your door. Therefore,
they can guarantee that the devices work correctly.

9.1 CESeasy app

For configuration you need the CESeasy app.
The CESeasy app is available for Android and iPhone. Simply scan the QR code to download the
app.
The QR code is able to detect whether you are using an Androidphone or iPhone, and
refers you to the correct app.
CESeasy app “access”
If the scan does not work, please open the following link on your smartphone. The link is also able
to detect whether you are using an Android phone or iPhone, and refers you to the correct app.
https://ces.qr1.at/CESeasyApp
Smartphone prerequisites:
l iOS (iOS 9.2 or higher) or Android (Android 4.4 or higher)
l If you use an iPhone: iPhone 4S or newer models
l Bluetooth 4.0 or higher
l suitable for Bluetooth Low Energy
Location transmission
To enable the CESeasy app to connect to the lock, the location transmission must be activated.
This applies to both the settings of the app itself (CESeasy app must be allowed to share the
location) and the location transmission of your smartphone (location transmission must be
activated for the smartphone).
If you use an Android smartphone, you may have to set the location transmission once
manually in the settings of the CESeasy app after it has been installed.
CESeasy motor cylinder Page 27 of 53
9 Configuration

9.2 Coupling

For safety reasons, the motor cylinder has to be connected to the app for manual firmware
updates and configuration. Thus, only people with a direct access to the motor cylinder can
update and configure it.
Tools required
Tool Required for
Smartphone with CESeasy app
Smartphone prerequisites:
l iOS (iOS 9.2 or higher) or Android (Android 4.4
or higher)
l If you use an iPhone: iPhone 4S or
newer models
l Bluetooth 4.0 or higher
l suitable for Bluetooth Low Energy
How to couple the motor cylinder with the CESeasy app
1. Loosen the design screw.
Configuration, firmware update and
test
2. Slide the cover of the battery compartment
downwards and remove it.
Page 28 of 53 CESeasy motor cylinder
9 Configuration
3. Press the coupling button in the battery compartment
of the motor cylinder for approx. 1 second.
Now, the motor cylinder periodically emits an acoustic
signal.
The motor cylinder has to be within the range of
the smartphone.
4. Open the CESeasy app on your smartphone.
5. Make sure you are in the “Locks” menu of the app.
Click on the “Scan” button in the upper right
corner.
In the menu options “Update” and “Config” you will now
see the motor cylinder.
As long as the motor cylinder is connected to the
app, it regularly emits an acoustic signal. This shows
that both are connected.
CESeasy motor cylinder Page 29 of 53
9 Configuration
6. If you click on “Config”, the configuration menu opens
(see "Configuration menu" on the facing page).
Make sure that you have carried out the first
firmware update before configuring the device.
Otherwise, your configuration will be overwritten by
the first firmware update. No subsequent firmware
updates will overwrite your configuration.
7. If you click on “Update”, a firmware update is carried
out (see "Firmware update" on page34).
Page 30 of 53 CESeasy motor cylinder
9 Configuration

9.3 Configuration menu

Make sure that you have carried out the first firmware update before configuring the
device. Otherwise, your configuration will be overwritten by the first firmware update. No
subsequent firmware updates will overwrite your configuration.
Test
For safety reasons, always test the functions when the door is open!
Night Tests the “Night locking” mode
If in night locking mode, the motor cylinder locks the door, which then no longer can be
mechanically opened. If someone tries to turn the rotary knob in the opening direction, the
motor cylinder exerts some force turning it in the closing direction. The night locking mode
is a break-in resistance property intended e.g. to prevent someone from turning the rotary
knob of the motor cylinder from the outside through the mail slot.
The night locking mode is deactivated when the lock is opened by remote control
or the CESeasy app.
To be able to open a door which is in night locking mode, you must have a remote
control or the CESeasy app. In an emergency, this could lead to life-threatening
situations!
Before you activate the night locking mode, be sure to note all requirements
concerning escape routes and fire protection (e.g. certain doors must not be
locked).
When in night locking mode, the motor prevents the knob from being manually
turned by exerting force in the opposite direction. This uses a lot of battery energy,
which is why they may empty more quickly when in night locking mode.
Close Locks the lock
Open Unlocks the lock
You can reverse the direction of rotation if the motor cylinder rotates in the wrong direction during
“Open" and “Close" (see below).
Configuration
Acoustic signal Acoustic signal after each closing/opening operation yes/no
Reverse dir-
ection of rota-
tion
Automatic clos-
ure
Changes the rotational direction of the motor. You have to change the direction of rotation
if the “Open” test shows that the motor rotates in the wrong direction.
If the function “Automatic closure” is activated, the motor cylinder automatically locks the
door after it has been closed.
CESeasy motor cylinder Page 31 of 53
This function requires a door contact.
The “Automatic closure” function increases the battery consumption.
Opening time Contains the settings for the time period the latch is pulled back.
Prolonged opening times increase battery consumption.
9 Configuration
Using the door
status sensor
Reversing the
door status
sensor
Type Lock type, e.g. motor cylinder or door controller
Power supply
unit
Battery Indicates the battery voltage measured in the device.
Firmware Shows the firmware version of the device.
Advanced Opens the expert menu for the CES service technician.
Advanced (expert menu)
Changing the settings in the expert menu could damage both the motor cylinder and the lock
irreversibly! Only change the settings if you know exactly what you are doing!
Here, if there is a door contact, you can define whether that door contact should be used.
Here you can reverse the signal of the door contact if the door contact signals “door open”
when the door is closed.
Indicates whether an optional power supply unit is connected or not.
To ensure that only trained experts can change the settings in the expert menu, it
is protected by a PIN code.
Settings which have been changed in the expert menu are saved in the motor cylinder. These
changes can affect manufacturer’s warranty!
Reset to
standard
settings
Rotational
speed
Turning time
to open
Turning time
to close
Reversing time
Open
Reversing time
Close
Resets the configuration settings to factory settings.
The speed at which the motor drives the cylinder. The rotational speed mainly determines
the force which is used to pull back the latchbolt during the day.
The maximum time during which the motor is turning to open the latchbolt. In general,
the motor stops turning in time because the end stop in the lock has been detected.
The maximum time during which the motor is turning to close the latchbolt. In general,
the motor stops turning in time because the end stop in the lock has been detected.
Determines how long the motor has to turn to pull back the latchbolt at daytime.
Determines how long the motor has to turn to release the lock after having reached the
end stop in closing direction.
Page 32 of 53 CESeasy motor cylinder
9 Configuration
Maximum cur-
rent
Door contact
Door contact
Transmission
power
Command The command line is intended to send commands to the device.
Bluetooth MAC Shows the bluetooth address of the device.
Boot version Here you can see the boot version of the device.
Module status Indicates the connection status between device and communication module:
The maximum motor current. The maximum motor current determines the force the
motor cylinder can permanently exert.
Here you can set the time which has to expire between a status change of the door contact
(door is either open or closed) and the device reaction to this status change.
Here you can reduce the Bluetooth transmission power.
Example: A building contains 10 doors with CESeasy locks. If the locks are located
relatively close to each other, a person with keys for all 10 locks will see a long,
confusing list of locks in the CESeasy app. If you reduce the transmission power of the
locks, the list of locks in the immediate vicinity will be reduced.
not connected The device is not coupled to a communication module
connected Device is coupled to a communication module
connected,
communication error
If the status is “connected” or “connected, communication error”, the button
“decouple” will be additionally displayed. Pressing this button will decouple the
device from the communication module.
Module ver-
sion
Data reset Resets the configuration settings to factory settings, as well as any data in the device
Test Here you can check the functions “night locking”, “open” and “close”.
Indicates either the firmware version for the communication module, or the firmware
version in the communication module.
If the device is coupled to the communication module, and both have communicated, the
current firmware version of the communication module is shown.
If the devices have not communicated yet, the firmware version which will be transferred
to the communication module during their next communication will be shown.
(events saved so far, database and clock).
Device is coupled to a communication module, but there is a
communication error
CESeasy motor cylinder Page 33 of 53
10 Firmware update

10 Firmware update

10.1 Automatic firmware updates

Automatic firmware update after installation
The first firmware update after installation should be carried out manually. However, if this has
not happened, the firmware update is carried out automatically after the device has been
operated by the CESeasy App. In this case, the CESeasy app shows a message, and the firmware
update will be completed after approx. 45 seconds.
Automatic firmware updates during operation
Firmware updates are automatically transmitted during operation by the CESeasy app. As soon as
the new firmware has been transmitted completely, the device operates on the new firmware.
Usually you do not notice the updating process.

10.2 Manual firmware updates

The following situations require a manual firmware update:
l The motor cylinder has been installed for the first time
l The motor cylinder has been reset to factory settings
How to proceed
See "Coupling" on page28.
Make sure that you have carried out the first
firmware update before configuring the device.
Otherwise, your configuration will be overwritten by
the first firmware update. No subsequent firmware
updates will overwrite your configuration.
A message is shown that the transmitted firmware
has been installed once the firmware has been
transmitted completely. The motor cylinder emits a
signal to indicate that the firmware installation has
been completed. Firmware installation takes about 30
seconds.
Page 34 of 53 CESeasy motor cylinder
11 Administration

11 Administration

11.1 CESeasy web platform

The device is managed on the CESeasy web platform. There you can issue keys, add remote
controls, etc.
For details, please refer to the manual for the CESeasy web platform.

11.2 Extension functions

Several extension functions are available at CES.
You can purchase these functions in the form of a prepaid card
which contains a code. Scratch the code off and add it to your lock
or account.
Lock management (for locks)
The “Lock management" function is part of the locks as delivered by CESeasy.
The “Lock management" function allows you to manage your locks for 5 years on the web
platform without any restrictions. You can extend it for another five years by buying an additional
“Lock management” function.
When “Lock management” has expired, lock management will be restricted:
l You can no longer issue keys for this lock, you can only retrieve them. (The keys issued
before this period expired are preserved)
l It is no longer possible to link a lock to a button of the remote control. (Buttons linked to a
lock before this period expired are preserved)
l If no lock in your account has the “Lock management" function any longer, you can no
longer add a remote control.
(The remote controls added before this period expired are preserved)
“Lock management" is linked to each lock.
CESeasy motor cylinder Page 35 of 53
11 Administration
The time starts to run upon the first lock registration. If you delete a lock, the functions
linked to it continue to be activated, and time continues to run. If this lock is registered
again, it is added to the account with the remaining time.
If you have activated the "5 additional keys" function for a lock, you can issue and retrieve
these keys for the lock in question only within the validity period. The additional keys do not
prolong the term of expiration.
5 additional keys (for locks)
This function provides you with five additional keys for one lock. Additional keys are only valid for
the lock to which you have added this extension function.
You can issue additional keys for one lock as long as you can also issue the keys which were
delivered to you together with the lock.
When you delete a lock you also delete all additional keys which were added to this lock.
Afterwards, these additional keys cannot be added to another lock.
Key to organisation (for locks)
This function allows you to issue keys not only to individuals but rather also to organisations. The
organisation which has received a key from you can pass it on to its employees.
This function is valid for five years. The time during which this function is valid starts to
run after you have added this function to the lock. If you delete the lock, time continues to
run. If this lock is registered again, it is added to the account with its remaining time.
The “Key to organisation" function can only be added and used if a valid “Lock
management” function has been added to it. The “Lock management" function is part of
the locks as delivered by CESeasy.
Building management (for lock owner accounts)
The “Building management" function allows you to manage buildings in the role of a building
manager. Your account is extended with the tab “Buildings" which allows you to create buildings
and to add locks to these buildings. If you own the “Building management” function, you can
additionally define how the name of the lock is displayed on the web platform and in the CESeasy
app.
The “Building management" function is used to extend two account types:
Page 36 of 53 CESeasy motor cylinder
11 Administration
l If you extend a lock owner account with the “Building management" function, you have a
lock owner account with building management.
l If you extend an organisation account with the “Building management" function, you
have a lock owner account with building management in addition to your organisation
account. You can switch between the accounts on the web platform.
The “Building management" function is valid for five years. It is linked to your lock owner account.
100 employees (for an organisation)
You can use the "100 employees” function in two ways:
l It allows you to manage 100 additional employees in your organisation. Initially, you can
manage 100 employees per organisation, while this function allows you to manage 200
employees in your organisation (or even more, if you buy this function several times).
If you manage several organisations with your organisation account: these
100 additional employees are added only to the organisation you have
selected when activating this function.
The “100 employees" function has a duration of five years.
l When the licence duration of your organisation has expired, you can prolong it by another
five years with the “100 employees” function.
Organisation (for organisation accounts)
You can use the "Organisation" function in two ways:
l It allows you to create an organisation account. This account automatically creates an
organisation with 100 employees.
l If you already own an organisation account, this function allows you to add another organ-
isation with 100 employees.
One organisation has a validity of 5 years. To extend its validity by another 5 years, you
have to add the function "100 employees" to this organisation.
CESeasy motor cylinder Page 37 of 53

12 Operation

12.1 How to use it with the rotary knob

The door can easily be locked or unlocked using the rotary knob. As
soon as you move the rotary knob in the direction “Lock” or “Unlock”,
the motor cylinder detects the movement and locks or unlocks the
door.
Night locking mode:
12 Operation
If in night locking mode, the motor cylinder locks the door, which then no longer can
be mechanically opened. If someone tries to turn the rotary knob in the opening
direction, the motor cylinder exerts some force turning it in the closing direction.
The night locking mode is a break-in resistance property intended e.g. to prevent
someone from turning the rotary knob of the motor cylinder from the outside
through the mail slot.
The night locking mode is deactivated when the lock is opened by remote
control or the CESeasy app.
To be able to open a door which is in night locking mode, you must have a
remote control or the CESeasy app. In an emergency, this could lead to life-
threatening situations!
Before you activate the night locking mode, be sure to note all requirements
concerning escape routes and fire protection (e.g. certain doors must not be
locked).
When in night locking mode, the motor prevents the knob from being
manually turned by exerting force in the opposite direction. This uses a lot of
battery energy, which is why they may empty more quickly when in night
locking mode.
Page 38 of 53 CESeasy motor cylinder
12 Operation

12.2 Operation with a mechanical key

You can always lock and unlock your door with a mechanical key from
the outside. A specific coupling in the motor cylinder disengages it as
soon as you insert a key into the mechanical cylinder.
However, you should always carry a mechanical key with you even if you operate your
motor cylinder by smartphone or remote control only. You can use it in an emergency, e.g.
if the batteries of the motor cylinder, the remote control or your smartphone are empty.

12.3 How to use it with a remote control

You can also operate the CESeasy motor cylinder with a remote
control. Press a button of the remote control not too far away from
the motor cylinder. The lock owner defines the functions assigned to
the buttons of the remote control.
For details, please refer to the manual for the CESeasy remote
control.
Remote control range
The remote control range depends on various factors:
l The lock environment (building materials of doors, walls, etc.)
l The remote control environment (the way it is held, if it is used inside or outside, etc.)
l The surrounding environment between lock and remote control (doors and walls between
them, further radio signals in the surroundings which could influence the communication,
etc.)

12.4 Operation via smartphone

You can operate the motor cylinder by means of the CESeasy app and
a suitable smartphone.
To operate the motor cylinder, you need a digital key. You can assign
digital keys to yourself or others on the CESeasy web platform.
For details, please refer to the manual for the CESeasy web
platform.
CESeasy motor cylinder Page 39 of 53
12 Operation
How to download the CESeasy app
The CESeasy app is available for Android and iPhone. Simply scan the QR code to download the
app.
The QR code is able to detect whether you are using an Androidphone or iPhone, and
refers you to the correct app.
CESeasy app “access”
If the scan does not work, please open the following link on your smartphone. The link is also able
to detect whether you are using an Android phone or iPhone, and refers you to the correct app.
https://ces.qr1.at/CESeasyApp
Smartphone prerequisites:
l iOS (iOS 9.2 or higher) or Android (Android 4.4 or higher)
l If you use an iPhone: iPhone 4S or newer models
l Bluetooth 4.0 or higher
l suitable for Bluetooth Low Energy
Location transmission
To enable the CESeasy app to connect to the lock, the location transmission must be activated.
This applies to both the settings of the app itself (CESeasy app must be allowed to share the
location) and the location transmission of your smartphone (location transmission must be
activated for the smartphone).
If you use an Android smartphone, you may have to set the location transmission once
manually in the settings of the CESeasy app after it has been installed.
Page 40 of 53 CESeasy motor cylinder
13 Technical data

13 Technical data

13.1 Equipment features

CESeasy motor cylinder Article number Motorised cylinder: 347100V
Complete package: EASY-xxx (xxx = profile range, e.g. WD5): Motor cylinder with mounted locking cylinder, 1 mechanical key, 5 digital keys, 1 remote control, 1 "lock management" function (5 years), door contact and connecting cable for door contact
Material ABS, lacquered / anodized aluminium Locking cylinder Each state-of-the-art CES locking system, incl. 1 key Cylinder profile Euro profile (PZ); optionally Swiss round profile (22mm)
Power supply Batteries 6 x AA alkaline batteries Power input 12 VDC / 2.5 A / stabilised Optional power supply unit 347130V Inputs and outputs Sensor input Input for an optional door contact (347129V). A special cable is required
(347110V). Set containing a door contact and a cable: 347128V Max. cable length: 30 cm
Further inputs and outputs Available via the CESeasy communication module RF-Transceiver RF-Transceiver 868 MHz, for remote controls and the communication module Bluetooth LE transceiver 2.4 GHz, to communicate with mobile phones Encryption AES128 Memory / capacity Number of digital keys 600 access group (1 access group = max. 65,000 employee keys, or 1 digital
key, or 1 remote control)
Encryption AES128 Service life Service life Min. 200.000 operations (at 20°C), in accordance with SKG Battery service life Approx. 7,500 operations (2 turns, latch and deadbolt, 1 Nm, at 20°C) in one
year
Environment Device environment The device side equipped with motor is suitable for indoor use only Operating temperature 0 … + 50°C Humidity during operation 5 … 90%, non-condensing Unsuitable climates Do not use in corrosive environments (chlorine, ammonia, lime water)
Tests and certificates Safety class SKG*** CE label NEN EN 300330-02, NEN EN 301489-03 Control and operation Mobile phone Compatible Apple device with BLE and iOS 9.2 or higher
Compatible* Android device with BLE and Android 4.4 or higher
* Due to the vast number of differentAndroid phones and versions, testing the compatibilityof a particular Android device is recommended.
CESeasy motor cylinder Page 41 of 53

13.2 Dimensions

13.2.1 Case with a mechanical cylinder
13 Technical data
Page 42 of 53 CESeasy motor cylinder
14 Optional accessories

14 Optional accessories

14.1 Door contact

The door contact transmits the information “door is locked” or “door is open” to the lock. This
information can be used for motor cylinders and door controllers.
A door contact allows you to use the “Automatic closure” function. The door contact enables the
motor cylinder to detect that the door is closed and thus automatically lock it.
The “Automatic closure” function increases the battery consumption.
You can use standard reed switches as door contacts. To connect the door contact to the motor
cylinder you need a connecting cable with a special plug. Both are available at CES:
Door contact 347129V
Connecting cable 347110V
Set containing a door contact and a connecting cable 347128V
14.1.1 How to install a door contact
How to install a door contact
1. Loosen the design screw by hand.
CESeasy motor cylinder Page 43 of 53
14 Optional accessories
2. Slide the cover of the battery compartment
downwards and remove it.
3. Insert the plug of the door contact cable into the
intended port (see image).
4. Remove the lug in the cover of the battery
compartment.
5. Run the connecting cable through the recess into the
motor cylinder (see picture).
6. Slide the cover back onto the battery compartment.
Page 44 of 53 CESeasy motor cylinder
14 Optional accessories
Make sure that the power cable runs into the cover
through the new opening (removed lug).
7. Install the door contact directly next to the motor
cylinder and the door. In doing so, follow the
instructions for the door contact.
8. Mount the magnet which belongs to the door contact
onto the door frame opposite the door contact.
9. Connect the connecting cable to the door contact.
If necessary, you can shorten the connecting cable,
but you cannot extend it. The door contact cable
must not exceed approx. 25cm. A cable which is too
long may lead to unintended behaviour.
10. In the configuration menu, activate the use of the
door contact (see "Configuration" on page27).
CESeasy motor cylinder Page 45 of 53

14.2 Power supply unit for external power supply

The motor cylinder can be connected to an external power supply unit.
Requirements of the power supply unit:
l Stabilised DC voltage of 12V ± 10%
l Current of max. 2.5A
14.2.1 How to connect the power supply unit
Tools required
Tool e.g. by
0.5 x 3.0 x 80 wrench Wera 335(5110001001)
14 Optional accessories
How to connect the power supply unit
1. Loosen the design screw by hand.
2. Slide the cover of the battery compartment downwards
and remove it.
3. Cut the wire ends to 6mm length.
Make sure that the wire ends are either tin-plated or
carry suitable wire end sleeves.
Page 46 of 53 CESeasy motor cylinder
14 Optional accessories
4. Push the wire ends into the connector, and carefully
tighten them.
Make sure to connect the cable correctly to the positive
and negative terminals as indicated in the connector of
the motor cylinder case.
+ next to the bottom side
- next to the button
5. Remove the lug in the cover of the battery compartment.
6. Run the power cable through the recess into the motor
cylinder (see picture).
7. Slide the cover back onto the battery compartment.
Make sure that the power cable runs into the cover
through the new opening (removed lug).
Now the external power supply unit is connected.
It is recommended to additionally insert batteries which
ensure that the motor cylinder can also be used in the
event of a power outage.
CESeasy motor cylinder Page 47 of 53
15 Disposal

15 Disposal

15.1 Notes on disposal

Device
In accordance with the Waste Electrical and Electronic Equipment recycling (WEEE) Regulations,
every consumer has a duty to dispose of old electronic/electrical appliances safely and separately
from household waste. It is forbidden to dispose of electronic devices in the household waste. You
can bring old devices free of charge to the local (council's) collection points. Or you can send the
device to C.Ed. Schulte GmbH Zylinderschlossfabrik, Velbert/Germany. Please make sure correct
postage is paid for the return.
The symbol with the crossed-out dust bin signifies old electrical appliances must not
be disposed of as household waste.
Electronic devices contain many different substances and materials. If old electronic devices are
not disposed of appropriately, the contaminants contained in them can lead to health and
environmental hazards. In addition, appropriate disposal allows recovery and re-use of recyclable
materials, which is a substantial contribution to maintaining natural resources.
Batteries
In accordance with the Waste Batteries and Accumulators Regulations 2009, every consumer has
a duty to return used and empty batteries. It is illegal to dispose of them in the household waste.
You may bring all batteries free-of-charge to any local (council’s) collection point that is part of the
waste battery collection scheme. You can also send used batteries that were delivered by CES
back to C.Ed. Schulte GmbH Zylinderschlossfabrik, Velbert/Germany. Please make sure correct
postage is paid for the return.
Used batteries may contain contaminants or heavy metals which can pose a health and
environmental hazard. Batteries are recycled, as they contain important raw materials like iron,
zinc, manganese, or nickel.
Page 48 of 53 CESeasy motor cylinder
15 Disposal
The symbol with the crossed-out dust bin signifies that batteries and rechargeable
batteries must not be disposed of as household waste. Beneath the symbol you may
also find the chemical designation of the substances contained, e.g.:
l (Pb) lead
l (Cd) cadmium
l (Hg) mercury
Collection points for batteries and rechargeable batteries are identified by a variety of
symbols.
Package
Packaging of the components is made from environmentally friendly, reusable materials. In detail,
these are:
l Outside packaging and inlays from cardboard
l Inlays and protective foils from Polyethylene (PE)
Please dispose of the packaging in an environmentally friendly way through waste
separation streams.
CESeasy motor cylinder Page 49 of 53
16 Index

16 Index

1
100 employees (extension function) 37
5
5 additional keys (extension function) 36
A
App 27
B
Batteries
Safety instructions 7
Battery consumption 23
Battery replacement 24
Building management (extension function) 36
C
CESeasy app 27
CESeasy web platform 35
Configuration 27
Coupling 28
Coupling button 29
Cylinder length (mechanical cylinder) 10
Page 50 of 53 CESeasy motor cylinder
D
Declaration of conformity 6
Dimensions 42
Door contact 43
Assembly 43
E
EU Declaration of conformity 6
Extension functions 35
16 Index
F
Firmware update 34
Functions (extension functions) 35
H
High burglary protection 9
K
Key
mechanical 39
Key to organisation 36
L
Lock management (extension function) 35
CESeasy motor cylinder Page 51 of 53
16 Index
M
Mechanical cylinder 10
N
Night locking mode 38
O
Organisation (extension function) 37
P
Power supply unit 46
Connection 46
R
Registration card 17
Remote control 39
Rotary knob 38
S
Safety instructions 6
Scope of delivery 17
W
Web platform 35
Page 52 of 53 CESeasy motor cylinder
C. Ed. Schulte GmbH Zylinderschlossfabrik
Friedrichstraße 243 D-42551 Velbert
+49 2051 204 0
+49 2051 204 229
info@ces.eu
CESnederland B.V.
Lage Brink 9 NL-7317 BD Apeldoorn
+31 55-52 66 89 0
+31 55-52 66 89 9
infonl@ces.eu
United Kingdom
CES Security Solutions Ltd.
Unit 4 Kendon Business Park Maritime Close, Medway City Estate Rochester, Kent ME2 4JF
+44 1 634 713 369
+44 1 634786833
info@uk.ces.eu
Middle East
A.G.P Advanced German Products LLC
PO Box 102761 UAE Dubai
+971 4 885 7050
+971 4 369 7051
+971 4 390 8935
info@agp-dubai.com
CESfrance SARL
8 Impasse Charles Petit F-75011 Paris
+33 1 44 87 07 56
+33 1 43 07 35 78
infofr@ces.eu
CESitalia srl
V. d. vecchie Fondamenta, 4 Straße d. A. Gründungen 4 I-39044 Egna / Neumarkt (BZ)
+39 0471 812 294
+39 0471 812 294
info@it.ces.eu
CESrom srl.
Str. Metalurgistilor 3 D RO-550137 Sibiu
+40 269-206 00 2
+40 269-206 00 5
info@ro.ces.eu
Austria
César A. Cárcamo
Büro: Wiener Bundesstrasse 33 A-4050 Traun
+43 660-73 20 311
+43 732-21 00 22 2681
office@ces.at
Belgium
LockingSystems
Guy Lambrechts Van Haeftenlaan 10 BE-2950 Kapellen
+32 497 946267
guy.lambrechts@ces.eu
Spain
Benidorm Locks S.L.
Av. Marina Baixa s / n Partida Torrent ES-03530 La Nucia, Alicante
+34 96 689 79 79
+34 96 689 79 78
info@benidormlocks.com
www.ces.eu
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use