Certance DAT 24, 24 User Manual

Download

CERTANC E

Online User's Guide

DAT24 Tape Drive

Part Number 50001756

April 2004

Certance and the Certance logo are trademarks of Certance LLC. Other product names are trademarks or registered trademarks of their respective owners.

Certance reserves the right to change, without notice, product offerings or specifications. No part of this publication may be reproduced in any form without written permission from Certance LLC.

Certance provides this manual “as is,” without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Certance reserves the right to change, without notification, the specifications contained in this manual.

Certance assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of this manual, nor for any problem that might arise from the use of the information in this manual.

Warnings

All safety and operating instructions should be read before this product is operated, and should be retained for future reference. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or fire hazards. In order not to defeat the safeguards, observe the follow-

ing basic rules for installation, use and servicing.

CAUTION: This symbol should alert the user to the presence of “dangerous voltage” inside the product that might cause harm or electric shock.

Caution! Risk of electric shock! Do not open! To reduce the risk of electric shock, do not remove the cover (or back). No user-serviceable parts

are inside. Refer servicing to qualified service personnel.

• Heed warnings — All warnings on the product and in the operating instructions should be adhered to.

• Follow instructions — All operating and use instructions should be followed.

• Ventilation — The product should be situated so that its location or position does not interfere with proper

ventilation.

• Heat — The product should be situated away from heat sources such as radiators, heat registers, fur-

naces, or other heat producing appliances.

• Power sources — The product should be connected to a power source only of the type directed in this

document or as marked on the product.

• Power cord protection — The power cord should be routed so that it is not likely to be walked on or

pinched by items placed upon or against it, paying particular attention to the cord at the wall receptacle, and the point where the cord exits from the product.

• To complete the disconnection of the electricity, please remove the power (electric) cord and the SCSI

cable from their connections in the back of the product. The plugs should be placed near the product for easy access.

• Object and liquid entry — Care should be taken to insure that objects do not fall and liquids are not

spilled into the product's enclosure through openings.

• Servicing — The user should not attempt to service the product beyond that described in the operating

instructions. All other servicing should be referred to qualified service personnel.

Precautions

• Do not use oil, solvents, gasoline, paint thinners, or insecticides on the unit.

• Do not expose the unit to moisture or to temperatures higher than 151 °F (66 °C) or lower than

-40 °F (-40°C).

• Keep the unit away from direct sunlight, strong magnetic fields, excessive dust, humidity, and

electronic/electrical equipment, which generate electrical noise.

• Hold the power cord by the head when removing it from the AC outlet; pulling the cord can damage the

internal wires.

• Use the unit on a firm level surface free from vibration, and do not place anything on top of the unit.

FCC Notice

This equipment generates and uses radio frequency energy and, if not installed and used properly — that is, in strict accordance with the manufacturer's instructions — may cause interference to radio communications or radio and television reception. It has been tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reason able protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient the receiving antenna.

• Relocate the computer with respect to the receiver.

• Move the computer into a different outlet so that the computer and receiver are on different branch

circuits.

If necessary, you should consult the dealer or an experienced radio/television technician for additional suggestions. You may find the booklet, How to Identify and Resolve Radio-TV Interference Problems, prepared by the Federal Communications Commission, helpful. This booklet (Stock No. 004-000-00345-4) is available from the

U.S. Government Printing Office, Washington, DC 20402.

WARNING: Changes or modifications made to this equipment, which have not been expressly approved by Certance, may cause radio and television interference problems that could void the user's authority to operate the equipment.

Further, this equipment complies with the limits for a Class B digital apparatus in accordance with Canadian Radio Interference Regulations.

Cet appareil numérique de la classe B est conforme au Règlement sur brouillage radioélectrique, C. R. C., ch.

1374.

The desktop device drive described in this manual requires shielded interface cables to comply with FCC emission limits.

WARNING: To prevent fire or electrical shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel.

Contents

Chapter 1 – Introduction .................................................. 9

Chapter 2 – Installation ................................................. 10

Introduction ........................................................................................10

Unpacking and Inspection ...................................................................10

Installing an Internal DAT24 Drive .........................................................10

Installing the Desktop DAT24 Drive .......................................................18

Chapter 3 – Operation................................................... 20

Introduction .......................................................................................20

Loading a Cartridge ...........................................................................20

Unloading a Cartridge ........................................................................21

Initializing a Blank DAT Cartridge .........................................................21

DAT Cartridge Compatibility ................................................................22

Write-Protecting a DAT Cartridge ..........................................................22

Cleaning the Tape Heads ....................................................................23

LED Codes .........................................................................................23

Chapter 4 – UNIX Settings ............................................. 26

Introduction ........................................................................................26

Setting DIP Switches for UNIX Support ..................................................26

Configuring Inquiry Strings ..................................................................27

Configuring for the DEC UNIX Environment ...........................................28

Configuring for the Sun Environment .....................................................29

Configuring for the SGI Environment .....................................................30

Configuring for the HP-UX Workstation Environment ................................32

Configuring for the IBM AIX Environment ...............................................33

Configuring for the SCO Environment ...................................................34

List of Figures

Figure 1. DIP Switches and Jumpers for Internal DAT24 Tape Drives ......................... 11

Figure 2. DIP Switch Settings for Internal DAT24 Drives........................................... 12

Figure 3. Location of Jumper Blocks on Internal DAT2 Drives.................................... 14

Figure 4. Mounting Holes for Internal DAT24 Drive in a 3.5-inch Configuration

(no mounting brackets) .......................................................................... 16

Figure 5. Mounting Holes for Internal DAT24 Drive in 5.25-inch Configuration

(with mounting brackets) ........................................................................ 16

Figure 6. Locations of SCSI Interface and Power Connectors on the Internal Drive ...... 17

Figure 7. Rear Panel of the Desktop Drive.............................................................. 19

Figure 8. SCSI Termination Examples.................................................................... 19

Figure 9. Loading a DAT Tape Cartridge (3.5-inch drive) ........................................ 20

Figure 10. Location of Tape Eject Button and Drive Status LED.................................. 21

Figure 11. Write-protect Tab on a DAT Cartridge................................................... 22

Figure 12. Status LEDs on the Front of the Drive...................................................... 24

vii

List of Tables

Table 1. DAT24 Models Covered in This User’s Guide.............................................. 9

Table 2. LED Flash Codes.................................................................................... 24

Table 3. Cartridge Status LED .............................................................................. 25

Table 4. Drive Configuration Settings.................................................................... 26

Table 5. Inquiry Strings ....................................................................................... 27

Table 6. DAT24 PRTNO Value............................................................................. 27

viii

1 Introduction

The Certance DAT24 is a digital audio tape (DAT) drive that supports the Digital Data Storage (DDS-

3) tape format. The DAT24 drive provides a typical capacity of 24 Gbytes, assuming 2:1 data com

pression (native capacity is 12 Gbytes).

The DAT24 tape drive can connect to a standard, single-ended SCSI or SCSI-2 interface. You can

use a 50-conductor flat cable or a 25-signal twisted-pair cable to connect the drive to a SCSI host

adapter. The cable should not exceed 6 meters (19.5 feet).

The DAT24 drive is offered as internal and desktop versions:

• The internal version is available as a 3.5-inch or 5.25-inch tape drive. It provides a 50-pin,

dual-row single-ended SCSI connector at the back of the drive.

• The desktop version provides two 50-pin, shielded connectors (ANSI Alternative 2) on the

back panel. These connectors consist of two rows of ribbon contacts spaced 2.16 mm (0.085

Tab le 1 on page 9 identifies the Certance DAT24 drive models and model numbers covered by this

User’s Guide.

Table 1. DAT24 Models Covered in This User’s Guide

in) apart. Either connector can be used as a SCSI IN or SCSI OUT connection.

Model Model Number

3.5-inch internal model STD124000N

5.25-inch internal model STD224000N

Desktop model STD624000N

2 Installation

Introduction

This chapter explains how to install the internal and desktop DAT24 tape drives.

Topics covered in this chapter are:

• “Unpacking and Inspection” on page 10

• “Installing an Internal DAT24 Drive” on page 10

• “Installing the Desktop DAT24 Drive” on page 18

Unpacking and Inspection

Although drives are inspected and carefully packaged at the factory, damage may occur during

shipping. Follow these steps for unpacking the drive.

1. Visually inspect the shipping containers and notify your carrier immediately of any damage.

2. Place shipping containers on a flat, clean, stable surface; then carefully remove the contents. If

the equipment is damaged, notify your Certance representative.

3. Always save the containers and packing materials for any future reshipment.

Installing an Internal DAT24 Drive

Installing the internal DAT24 drive involves the following steps:

1. Observe the guidelines and cautions for handling internal tape drives. See “Internal Tape

Drive Guidelines and Cautions” on page 11.

2. Configure the drive. See “Configuring the Internal DAT24 Drive” on page 11.

3. Mount the drive. See “Mounting an Internal DAT24 Drive” on page 15.

4. Connect the power and interface cables. See “Connecting Power and Interface Cables” on

page 17.

5. Registering the tape drive. After you install the DAT24, register it. Registering it ensures that

you will receive the latest information about the drive, as well as other product, service, and support information. For your convenience, you can register the DAT24 through our Web site at http://register.certance.com.

NOTE: Internal drives come in two mounting configurations. Drives configured for 5.25-inch bays are identical to those designed for 3.5-inch bays, except that drive-mounting brackets have been added on each side of the drive. Installation procedures are the same for both drive configurations.

Installation Installing an Internal DAT24 Drive

Internal Tape Drive Guidelines and Cautions

The following guidelines and cautions apply to handling and installing the internal DAT24 tape drive. Keep them in mind as you install the internal drive.

• Handle the drive by the sides rather than by the top cover to reduce the risk of dropping the

drive or damaging it during installation.

• Internal drives contain some exposed components that are sensitive to static electricity. To

reduce the possibility of damage from static discharge, the drives are shipped in a protective antistatic bag. Do not remove the drive from the antistatic bag until you are ready to install it.

• Before you remove the drive from the antistatic bag, touch a metal or grounded surface to dis-

charge any static electricity buildup from your body.

• Always lay the drive either on top of the antistatic bag or place it inside of the bag to reduce

the chance of damage from static discharge.

Configuring the Internal DAT24 Drive

Before you install the internal DAT24 tape drive in your computer, you may need to set the drive's SCSI ID or other drive features. Most features are set using a bank of dip-switches on the underside of the drive (see figure the drive for remote SCSI address selection, use the jumpers on the back of the drive, above

the interface and power connectors.

Figure 1 on page 11). To control SCSI termination and terminator power, or to con-

Dip switches

Note: Drive is shown upside down

SCSI jumper block

Figure 1. DIP Switches and Jumpers for Internal DAT24 Tape Drives

The default settings for internal DAT24 tape drives are:

• SCSI ID is 0.

• Drive reads and writes both MRS and non-MRS 4-mm media.

• Parity checking is disabled.

• Data compression is enabled.

• Power-on self-test diagnostics are disabled.

• SCSI termination is disabled.

If the default settings are appropriate for your computer system, skip ahead to “Mounting an Internal DAT24 Drive” on page 15. Otherwise, proceed to “Changing DIP Switch Settings” on page 12.

Installation Installing an Internal DAT24 Drive

Changing DIP Switch Settings

Figure 2 on page 12 shows the location of DIP switches on the underside of the internal DAT24 drive. Factory-default settings for each switch are also shown in Figure 2 on page 12. These settings are described in detail on the following pages.

Block of 10 dip switches

123456789

Note: Drive is shown upside down

Default dip-switch settings:

S3 S4 S5 S6

Key to dip-switch settings:

SCSI ID

SCSI ID Selection

OFF

MRS

Mode

All

MRS only

Parity

Enable

Disable

Data

compression

Disable

Enable

Inquiry

String

Seagate

Archive

*Some drives may be factory-configured to use the Archive inquiry string.

Figure 2. DIP Switch Settings for Internal DAT24 Drives

NOTE: If you change a DIP switch setting, the new setting does not take effect until you restart the drive or send a SCSI Bus Reset to the drive.

S7*

Self-test

Enable

Disable

S10

UNIX

Configuration

see text

OFF

SCSI ID Switches (Switches 1 through 3)

Switches 1, 2, and 3 correspond to the SCSI device address identification bits 0 (least-significant bit), 1, and 2 (most-significant bit), respectively. The default setting is SCSI ID 0 (all three switches

OFF).

NOTE: Each SCSI device on a bus must have a unique SCSI ID. The SCSI host controller generally uses ID 7. In some systems, the boot drive uses ID 0.

Installation Installing an Internal DAT24 Drive

Media Recognition System (Switch 4)

• Switch 4 ON = Media Recognition System mode disabled (default)

• Switch 4 OFF = Media Recognition System mode enabled

The media-recognition system allows the drive to determine whether a DAT tape supports the DDS standard. Using non-DDS media may appear to give satisfactory results, but the inferior specifica tions of such media can cause data-integrity problems.

Switch 4 enables or disables Media Recognition System (MRS) mode. If switch 4 is ON (the default setting), the drive reads or writes both MRS and non-MRS 4-mm media. If switch 4 is OFF, the drive reads and writes to MRS media, and reads from but does not write to 4-mm media.

Parity Check (Switch 5)

• Switch 5 ON = Parity checking enabled

• Switch 5 OFF = Parity checking disabled (default)

Switch 5 enables or disables parity checking for the SCSI bus. If switch 5 is ON, parity checking is enabled. If switch 5 is OFF (the default setting) parity checking is disabled, but parity is still gener ated by the drive.

DDS Pass-through Mode (Switch 6)

• Switch 6 ON = DDS pass-through data compression disabled

• Switch 6 OFF = DDS pass-through data compression enabled (default)

If switch 6 is OFF (the default setting), DDS pass-through data compression is enabled. If switch 6 is ON, data compression is disabled.

NOTE: The setting of switch 6 can be overridden if the host computer issues the appropriate SCSI Mode Select command.

Inquiry String (Switch 7)

• Switch 7 ON = Drive identifies itself as a Seagate DAT drive (default)

• Switch 7 OFF = Drive identifies itself as an Archive Python drive

If switch 7 is ON, the drive generates a SCSI inquiry string that identifies it as a Seagate DAT drive. For compatibility with older software and operating systems, the drive can be configured as an Archive Python drive by setting switch 7 to OFF.

Installation Installing an Internal DAT24 Drive

Power On Self Test (Switch 8)

• Switch 8 ON = Drive performs Power On Self Test

• Switch 8 OFF = Drive does not perform Power On Self Test (default)

Switch 8 enables or disables execution of Power On Self Test (POST) diagnostics when powered on. If switch 8 is OFF (the default setting), the drive does not perform a POST. If switch 8 is ON, the drive responds to SCSI commands only after successful completion of the POST (about 5 seconds).

UNIX Operating Systems (Switches 9 and 10)

Switches 9 and 10 configure the DAT24 tape drive for use with UNIX operating systems. For more information, see

Chapter 4, “UNIX Settings” on page 26.

Jumper Settings

Configuration jumpers on the back of the drive control SCSI bus termination and terminator power. The jumpers can also be used for remote SCSI address selection. locations of the jumper block and jumper settings for the internal DAT drive.

Figure 3 on page 14 shows the

Jumper Block

Termination Power

(Jumper on pins 15-16 enables termination power)

9 7654321

1211141316

Remote SCSI ID

SCSI Termination

(Jumper on pins 11-12 enables active termination)

Jumper ON

Pins 5-6 OFF OFF OFF OFF ON ON ON ON

Jumper OFF

Pins

3-4

1-2

OFF

SCSI ID 0 1 2 3 4 5 6 7

Figure 3. Location of Jumper Blocks on Internal DAT2 Drives

Settings for each jumper described in detail in the following pages. The default settings are:

• Terminator power is disabled.

• Active termination is disabled.

Installation Installing an Internal DAT24 Drive

Enabling SCSI Termination

Active SCSI termination is disabled as the factory default. If the drive is the only device on the SCSI bus, or if it is the last device on the bus, enable active termination by placing a jumper across pins 11 and 12.

Terminator Power

You can enable terminator power if needed for terminators or other SCSI devices through a jumper placement. The factory default for internal drives is that terminator power is disabled. To enable ter minator power, place a jumper across pins 15 and 16, as shown in Figure 3 on page 14.

Caution. If the jumper is installed, be careful not to short the TERMPWR signal to ground.

The drive contains a terminator power fuse to prevent damage to drive components in case the terminator power is shorted. If terminator power is enabled and the SCSI cable is connected upside down, for example, this fuse may blow to prevent damage to the drive. If this occurs, the drive will no longer supply terminator power to the bus. To replace the fuse, return the drive to an authorized repair facility.

Remote SCSI Address Selection

Use pins 1 through 6 to select the SCSI address remotely. To do so, connect a remote SCSI ID switch to pins 1 through 6.

• Pins 1 and 2 configure SCSI ID bit 0.

• Pins 3 and 4 configure SCSI ID bit 1.

• Pins 5 and 6 configure SCSI ID bit 2.

NOTE: If you use remote SCSI ID selection, set switches 1 through 3 to the OFF position (see Figure 1 on page 11).

Mounting an Internal DAT24 Drive

You can install the internal DAT24 drive horizontally or vertically (on its side).

Mounting the Drive in a 3.5-inch Drive Bay

To mount the drive in a 3.5-inch drive bay, mount the drive using two M3.0 metric screws on each side of the drive. Do not use screws longer than 4 mm or you may damage the drive. The 3.5-inch drive has four screw holes on the bottom and five on each side (see

Figure 4 on page 16).

Installation Installing an Internal DAT24 Drive

41.3 mm

35.0 mm (1.38 in)

2 PLACES

(1.63 in)

28.3 mm (1.11 in)

2 PLACES

8.0 mm (.31 in)

2 PLACES

5.0 mm (.20 in)

2 PLACES

30.0 mm (1.18 in)

2 PLACES

3.8 mm (.15 in)

2 PLACES

101.6 mm (4.00 in)

94.0 mm (3.70 in)

45.0 mm (1.77 in)

M3.0 X

4 DEEP MIN.

4 PLACES

60.0 mm (2.36 in)

2 PLACES

21.0 mm (.83 in)

2 PLACES

152 mm (5.98 in)

70.0 mm (2.76 in)

31.0 mm (1.22 in)

104.1 mm (4.10 in)

Bottom View

M3.0 X

4 DEEP MIN.

10 PLACES

6 mm

(.24 in)

2 PLACES

41.2 mm (1.62 in)

Side View

Figure 4. Mounting Holes for Internal DAT24 Drive in a 3.5-inch Configuration (no mounting brackets)

Mounting the Drive in a 5.25-inch Drive Bay

To mount the drive in a 5.25-inch drive bay, use a drive with mounting brackets. The 5.25-inch drive brackets have four screw holes on the bottom and six on each side (see

41.3 mm (1.63 in)

9.9 mm (.39 in)

2 PLACES

21.8 mm (.86 in)

2 PLACES

31.5 mm

(1.24 in)

2 PLACES

M3.0 X

4 DEEP MIN.

12 PLACES

4 DEEP MIN.

4 PLACES

M3.0 X

146 mm (5.74 in)

139.7 mm (5.50 in)

Figure 5 on page 16).

79.4 mm (3.13 in)

180.6 mm

2 PLACES

(7.11 in)

47.6 mm (1.87 in)

2 PLACES

41.2 mm (1.62 in)

Side View

6 mm

(.24 in)

2 PLACES

Figure 5. Mounting Holes for Internal DAT24 Drive in 5.25-inch Configuration (with mounting brackets)

79.4 mm (3.13 in)

47.6 mm (1.87 in)

148.5 mm (5.84 in)

Bottom View

Installation Installing an Internal DAT24 Drive

Connecting Power and Interface Cables

Attach the power and SCSI interface cables to the appropriate connectors on the back of the drive. Figure 6 on page 17 shows the locations of these connections.

Connecting the SCSI Interface Cable

Turn off all power to the drive and host computer. Attach the SCSI cable, making sure to align pin 1 on the cable with pin 1 on the drive. Pin 1 on the SCSI connector is to your right as you look at the back of the drive (see Figure 6). Your SCSI cable should have pin 1 highlighted by a colored stripe.

Connecting the Power Cable

Attach a 4-pin power connector from the system power supply to the connector on the back of the drive. The recommended 4-pin power connector for the internal drive is an AMP 1-48024-0 housing with AMP 60617-1 pins or equivalent.

4-pin

power

connector

SCSI pin 1

SCSI connector

Figure 6. Locations of SCSI Interface and Power Connectors on the Internal Drive

Installation Installing the Desktop DAT24 Drive

Installing the Desktop DAT24 Drive

The desktop DAT24 tape drive is a compact external unit that connects to the host computer as a turnkey subsystem. Installing the external drive involves the following steps:

1. Configure the drive. See “Configuring the Desktop DAT24 Drive” on page 18.

2. Set the SCSI ID. See “Setting the SCSI ID” on page 18.

3. Connect the SCSI interface cable. See “Connecting the SCSI Interface Cable” on page 19.

4. Connect the power cord. See “Connecting the Power Cord” on page 19.

5. Registering the tape drive. After you install the DAT24, register it. Registering it ensures that

Configuring the Desktop DAT24 Drive

The following is the default configuration for desktop DAT24 tape drive:

• Drive reads and writes both MRS and non-MRS 4-mm media.

• Parity checking is disabled.

• DDS-DC data compression is enabled.

• POST is disabled.

• Termination power is supplied to the SCSI bus.

NOTE: Some configuration settings can be changed using the SCSI Mode Select command. SCSI command information for Certance DAT drives is provided in the product description manual.

Setting the SCSI ID

Be sure the drive is turned off; then set the SCSI ID for the drive using the push-button switch on the back of the external drive.

connectors, the on/off switch, and the power-cord connector.

NOTE: The drive must be restarted, or a SCSI bus reset must be issued to have the new SCSI ID take effect.

Figure 7 on page 19 shows this switch, as well as the two SCSI interface

Installation Installing the Desktop DAT24 Drive

Push-button

Switch

ON/OFF

Switch

Power

SCSI

Connector

Connectors

Figure 7. Rear Panel of the Desktop Drive

Connecting the SCSI Interface Cable

The desktop DAT24 tape drive has two SCSI connectors to allow daisy chaining (see Figure 7 on page 19. You can use either connector to attach the drive to the host computer or to another SCSI

device.

NOTE: Turn off all power before connecting or disconnecting SCSI cables or terminating plugs.

If the desktop drive is the last device or the only device in a SCSI chain, install a terminating plug on the unused SCSI connector.

External SCSI device

(termination enabled)

External SCSI device

SCSI Controller

(termination enabled)

Example 1: SCSI termination in a system that has only external SCSI devices.

Figure 8 on page 19 shows two SCSI termination examples.

External SCSI device

(termination enabled)

External SCSI device

SCSI Controller

Internal SCSI device

(termination enabled)

Example 2: SCSI termination in a system that has both internal and external SCSI devices.

Figure 8. SCSI Termination Examples

Connecting the Power Cord

Attach the power cord securely to the power connector on the back of the drive. Figure 7 on page 19 shows the location of the power connector.

3 Operation

Introduction

This chapter describes how to use your internal or external DAT24 tape drive.

Topics covered in this chapter are:

• “Loading a Cartridge” on page 20

• “Unloading a Cartridge” on page 21

• “Initializing a Blank DAT Cartridge” on page 21

• “DAT Cartridge Compatibility” on page 22

Caution. To avoid data loss, clean the drive heads using a DDS head-cleaning cartridge after every 25 hours of read/write operation, or whenever the green cartridge-status LED flashes during operation. See page 23 for cleaning procedure.

Loading a Cartridge

The DAT24 tape drive has a front-loading cartridge bay for easy operation. The drive-bay door opens automatically when a cartridge is inserted. inserted into a 3.5-inch internal drive. After you insert the cartridge, there will be a brief delay while the drive identifies the cartridge type and state and moves the tape to the data area.

Figure 9. Loading a DAT Tape Cartridge (3.5-inch drive)

Figure 9 on page 20 shows a cartridge being

Operation Unloading a Cartridge

Unloading a Cartridge

Caution. Do not push the eject button while the Drive Status LED is ON. Otherwise, you may lose data.

Be sure the drive-status LED is not lit. Then unload the cartridge by pressing the eject button. For the location of the eject button, see automatically flushes the drive buffer to tape, updates the system log, and rewinds the cartridge

before ejecting it.

NOTE: Several seconds may elapse between the time you press the eject button and the time the cartridge is ejected. Do not power down the tape drive or the host computer during this time.

Figure 10 on page 21. After you press the eject button, the drive

Internal

DAT drive

External

DAT drive

Figure 10. Location of Tape Eject Button and Drive Status LED

Cassette Insertion Slot

Drive status LED

Cassette Insertion Slot

Eject Button

Initializing a Blank DAT Cartridge

When you insert a blank cartridge into the drive for the first time, the drive takes about 10 to 12 seconds to determine that the tape is blank. The drive automatically initializes the tape as soon as it receives a Write command from the host computer. Initializing a blank tape takes about 30 seconds.

While a tape is being initialized, the normal write operation continues until all internal buffers are filled. Ejecting the cartridge before the initialization is complete causes the procedure to abort. The

initialization restarts from the beginning the next time a Write command is received.

NOTE: The data buffer of the drive is flushed to tape if a Rewind command is issued, if the eject button is pushed, or if a delay in SCSI activity occurs. By default, the delay before the flush occurs is set to one minute. However, this delay time can be modified by the host application using a Mode Select command.

Operation DAT Cartridge Compatibility

DAT Cartridge Compatibility

The DAT24 tape drive is designed to use data-grade DDS DAT cartridges that comply with ANSI specifications listed in the “3.81 mm Helical-Scan Digital Computer Tape Cartridge for Information Interchange,” ANSI X3B5/89-156 standard. To ensure optimal data integrity and reliability, we rec ommend using Certance-brand DDS-3 cartridges (CDM24).

The DAT24 drive also recognizes 120-meter MP+ cartridges and other MRS cartridges when MRS is enabled. MRS cartridges have a series of alternate opaque and clear stripes at the beginning of the

tape. These stripes classify the media as data-grade, rather than audio-grade.

NOTE: A slowly flashing green LED in conjunction with the yellow LED indicates that a prerecorded audio tape has been inserted in the drive.

Four recognition holes allow the drive to identify the type of tape, determine its magnetic thickness, and to determine whether the tape is prerecorded or unrecorded or is a cleaning cartridge. Other cartridge features that allow the drive to optically sense cartridge in are Beginning-of-tape and Endof-tape.

Write-Protecting a DAT Cartridge

Figure 11 on page 22 shows how to write-protect or write-enable a DAT tape using the sliding writeprotect tab. You can only write data to the tape when the tab is in the closed position.

Write

Enabled

Figure 11. Write-protect Tab on a DAT Cartridge

Write

Protected

Operation Cleaning the Tape Heads

Cleaning the Tape Heads

If excessive magnetic dust or debris collects at one or more of the tape heads, your drive may not be able to read from or write to tape. To avoid this situation, you must clean the tape heads on your DAT drive

• After the first four hours of tape movement of a new cartridge.

• After every 25 hours of read/write operation.

• Whenever the rectangular, green Cartridge-status LED flashes during operation.

NOTE: A slowly flashing green LED may indicate that a tape is damaged or is nearing the end of its life. If cleaning the head does not correct the flashing LED condition, replace the cartridge. The slowly flashing LED does not indicate a loss of data, nor does it indicate SCSI problems.

To clean the tape heads on your DAT drive, use only a Certance-qualified DDS DAT cleaning cartridge designed for DAT drives, such as Certance Model CDMCL.

After you insert the cleaning cartridge, the drive detects that the cartridge is a cleaning cartridge, then loads and runs the cartridge for about 30 seconds. When cleaning is complete, the drive ejects the cartridge.

Each time the cleaning cartridge is loaded, a new, unused portion of cleaning tape is advanced over the entire tape path. The drive does not rewind a cleaning cartridge. After about 30 cleaning cycles the entire tape is used up and you must purchase a new cleaning cartridge.

If you insert a cleaning tape that has been used up, the drive ejects the tape without completing a cleaning operation. This process takes just under 25 seconds.

LED Codes

As Figure 12 on page 24 shows, the front panel of the DAT24 tape drive has two rectangular LEDs. These two indicators provide information about both normal and error conditions.

• The yellow rectangular LED indicates the condition of the tape drive.

• The green LED indicates the condition of the tape cartridge.

NOTE: Do not use an audio DAT cleaning cartridge. The drive cannot recognize it.

NOTE: The external DAT24 drive also has a round, green power-on LED on the front panel.

Operation LED Codes

Internal

DAT drive

Cartridge

Status LED

(green)

Cassette Insertion Slot

Drive

Status LED

(yellow)

External

DAT drive

Power

LED

Cassette Insertion Slot

Figure 12. Status LEDs on the Front of the Drive

Tab le 2 on page 24 summarizes the LED flash codes for DAT24 drives.

Table 2. LED Flash Codes

LED Color Action Meaning

Yellow ON (lit) The drive is reading or writing normally.

Yellow Flashing Rapidly A hardware fault occurred.

Green ON (lit) A cartridge has been inserted and is operating

normally.

Green Flashing Slowly A cartridge has been inserted but is generating

excessive errors beyond a predefined error threshold (warning only). Use a DDS cleaning cartridge to clean the heads.

Green Flashing Rapidly The drive could not write the tape correctly (a

write error has occurred). Try using a DDS DAT cleaning cartridge to clean the heads or try a new cartridge.

Green and Yellow Both flashing slowly A prerecorded audio cartridge has been

inserted and is being played automatically.

Green power LED (external drives) ON (lit) The external drive is powered on.

Operation LED Codes

Drive Status LED

The Drive Status LED is yellow and indicates the following conditions:

If the Drive Status light is ON continuously, the drive is reading or writing the tape (that is, SCSI or DAT activity is present). If you push the eject button while the Drive Status LED is ON, you may lose

data.

NOTE: If a SCSI Prevent Media Removal command has been issued, the Drive Status LED remains ON until the command is canceled.

If the Drive Status LED is flashing rapidly, a hardware fault has occurred. If this occurs immediately after power-on and you have enabled the Power On Self Test (POST) through a jumper setting, the POST may have failed and the drive will not operate.

Cartridge Status LED

The green, rectangular Cartridge Status LED indicates the following conditions:

Table 3. Cartridge Status LED

LED Status Meaning

ON (lit) A DAT cartridge has been inserted and the drive is operating normally.

Flashing Slowly The tape cartridge in the drive has generated a significant number of

data retries beyond a predefined DDS error threshold. This signal is a warning only and does not indicate data loss. If you see this signal, remove the tape and clean the tape heads using an approved DDS DAT cleaning cartridge. If the LED continues flashing or flashes when ejecting the cartridge, use a new cartridge for future writes.

Flashing Rapidly The drive could not write the tape correctly (maximum rewrite count

exceeded) and the write operation failed. Clean the drive heads using an approved DDS DAT cleaning cartridge. If the LED continues flashing, use a new cartridge for future writes

Cartridge Status LED and the Drive Status LED Flashing Slowly

NOTE: As routine maintenance, you should clean the drive heads after every 25 hours of operation. See page 23.

A prerecorded audio cartridge is being played automatically.

4 UNIX Settings

Introduction

This chapter describes how to configure the DAT24 tape drive to operate on various UNIX systems. It provides drive configuration options and any changes required at the operating system level. When configured as documented in this guide, the drive performs as an integrated component of the system, giving maximum functionality.

Topics covered in this chapter are:

• “Setting DIP Switches for UNIX Support” on page 26

• “Configuring Inquiry Strings” on page 27

• “Configuring for the DEC UNIX Environment” on page 28

• “Configuring for the Sun Environment” on page 29

• “Configuring for the SGI Environment” on page 30

• “Configuring for the HP-UX Workstation Environment” on page 32

• “Configuring for the IBM AIX Environment” on page 33

• “Configuring for the SCO Environment” on page 34

Setting DIP Switches for UNIX Support

Switches 9 and 10 on the bottom of the DAT24 tape drive are used for UNIX support, as shown in Tab le 4 on page 26.

Table 4. Drive Configuration Settings

System Switch 9 Setting Switch 10 Setting

Sun OFF ON

DEC ON OFF

IBM OFF ON

HP OFF OFF

SGI OFF OFF

SCO OFF OFF

Non-UNIX OFF OFF

UNIX Settings Configuring Inquiry Strings

Configuring Inquiry Strings

The DAT24 tape drive returns different inquiry strings, based on the setting of Switch 7 (see Table 5 on page 27).

Table 5. In quiry S trings

Inquiry String Returned Switch 7 Setting

ARCHIVE Python 04106-XXX OFF

SEAGATE DAT 04106-XXX ON

Either setting for Switch 7 can be used, but the correct inquiry string must be entered in the System Configuration information. For simplicity, the ARCHIVE Python string is used in the following sec

tions. If Switch 7 is set to ON, change the string to "SEAGATE DAT.”

NOTE: There are three spaces at the end of "SEAGATE DAT " to give the same overall length as the "ARCHIVE Python" inquiry string. Be sure to insert four spaces between DAT and 04106 when the full inquiry string is required.

Tab le 6 on page 27 shows the PRTNO value in the inquiry string for the DAT24 tape drive. When you make the actual kernel modifications, replace PRTNO with the required number:

Table 6. DAT24 PRTNO Value

Model Number PRTNO Value

STD224000N-SB 04106

UNIX Settings Configuring for the DEC UNIX Environment

Configuring for the DEC UNIX Environment

Digital UNIX Versions 4.0 and Later

With version 4.0 of their UNIX operating system, DEC introduced a new method of configuring the CAM SCSI driver. Modify the file /etc/ddr.dbase as follows:

1. Locate the Database entry for the DEC TLZ07 DAT drive

2. Copy this entry and paste it later in the file, taking care to maintain the file syntax.

3. Modify the new entry as shown below. Modified sections are shown in bold. See “Configur-

ing Inquiry Strings” on page 27 for information about drive inquiry strings:

SCSIDEVICE # Type = tape Name = "ARCHIVE" "Python" # PARAMETERS: TypeSubClass = rdat TagQueueDepth = 0 MaxTransferSize = 0x0ffffff #(16MB-1) ReadyTimeSeconds = 60 # seconds

DENSITY: # DensityNumber = 0,3,4,5,6,7 DensityCode = default CompressionCode = 0x0 Buffered = 0x1

DENSITY: # DensityNumber = 1,2 DensityCode = default CompressionCode = 0x1 Buffered = 0x1

4. Save the file.

5. Run the command ddr_config -c

ddr_config takes the default input file, ddr.dbase, and build a new device database. This is effective immediately, and there is no need to rebuild the kernel.

NOTE: ddr.dbase is a unix shell script and is not written in C. This means # is used to signify a comment, not /* and */ or //, as used in C. Make sure any comments included in this file are preceded with the # character.

UNIX Settings Configuring for the Sun Environment

Digital UNIX Versions Earlier Than 4.0

System configuration is achieved by modifying the file, cam_data.c. This is located in either /usr/ sys/data or /sys/data, depending on system configuration. Modify it as follows:

1. Locate the entry for the "TLZ07 - RDAT" drive.

2. Copy this entry and paste it later in the file, taking care to maintain the syntax of the C source.

3. Modify the new entry as shown below. Modified sections are shown in bold. See “Configur-

ing Inquiry Strings” on page 27 for information about drive inquiry strings:

/* Seagate DAT Drive "ARCHIVE Python" Inquiry, (Switch 7 off) */

{"ARCHIVE Python", 14, DEV_TLZ07,

(ALL_DTYPE_SEQUENTIAL << DTYPE_SHFT) | SZ_RDAT_CLASS,

(struct pt_info *)ccmn_null_sizes, SZ_NO_BLK, (DEC_MAX_REC - 1),

&tlz07_dens, NO_MODE_TAB, SZ_NO_FLAGS,

NO_OPT_CMDS, SZ_READY_DEF, SZ_NO_QUE,

DD_REQSNS_VAL | DD_INQ_VAL, 36, 64

4. Rebuild the kernel using the doconfig script, and re-boot the system

Configuring for the Sun Environment

Sun OS 4.1.x

To configure SunOS 4.1.x explicitly to use the DAT24 tape drive, modify the stdef.h and st_conf.c files (in the directory /usr/sys/scsi/ targets), then rebuild the kernel, as described below:

1. Modify the stdef.h file by adding a define statement for the DAT24 tape drive similar to the

one shown below:

#define ST_TYPE_SEAGATE_DAT <value>

Add this line after the last ST_TYPE_ define statement in the file. <value> should be the next unused hexadecimal value. This value will depend on the release and number of devices sup ported by the system. For example, if the last value for an existing device is 0x2d, then use a value of 0x2e.

2. Modify the st_conf.c file by adding the following lines at the end of the device definition list.

See

“Configuring Inquiry Strings” on page 27 for information about drive inquiry strings:

/*Seagate DAT support */

{

"Seagate DAT Drive",14,"ARCHIVE

Python",ST_TYPE_SEAGATE_DAT,10240,

5000,5000,

{0x0,0x8c,0x8c,0x8c},

{0,0,0,0}

}

UNIX Settings Configuring for the SGI Environment

3. Use the config command to rebuild the kernel and include the new device definition. Refer to

the config man page for details

Solaris 2.x

To configure Solaris 2.x to use the DAT24 tape drive, add the following lines to the file st.conf in the directory /kernel/drv.

tape-config-list=

"ARCHIVE Python PRTNO-XXX","Seagate DAT Drive","SEAGATE_DAT";

SEAGATE_DAT = 1,0x2c,0,0xd639,4,0x00,0x8C,0x8C,0x8C,3;

NOTE: The inquiry string above contains one space between Python and PRTNO. See the beginning of this chapter for information about replacing PRTNO with the number applicable to your DAT24 drive.

Once st.conf has been modified, the kernel must be reconfigured by booting the system using the boot -r command

Configuring for the SGI Environment

Irix V5.x

To configure Irix 5.x to use the DAT24 tape drive, modify the file /var/sysgen/master.d/scsi as described below:

1. Add the following entry to the file /var/sysgen/master.d/scsi.

{DATTAPE,TPDAT,7,12,"ARCHIVE","Python PRTNO"/*DAT*/,0,0,{0,0,0,0},

MTCAN_SILI|MTCAN_SEEK|MTCAN_CHTYPEANY,

/* minimum delay on i/o is 12 minutes, to allow the Drives

* full error recovery sequence to be performed. */

40, 12*60, 12*60, 12*60, 512, 512*512 },

2. Rebuild the kernel, as described below.

NOTE: The main difference between support on Irix 5.x and 6.x is the introduction of Data Compression switching via software in Irix version 6.2. When running 5.x, the drive always operates in the compression setting determined by Switch (OFF = compression enabled (default), ON = compression disabled).

See the beginning of this chapter for information on changing the inquiry string and replacing PRTNO with the number applicable to your DAT24 drive.

UNIX Settings Configuring for the SGI Environment

Irix V6.x

To configure Irix 6.x to use the DAT24 tape drive, modify the files /var/sysgen/master.d/scsi and / dev/MAKEDEV.d/TPS_base, then rebuild the kernel, as described below:

1. Add the following entry to the file /var/sysgen/master.d/scsi

{ DATTAPE, TPDAT, 7, 12, "ARCHIVE", "Python PRTNO"/*DAT*/, 0, 0, {0},

/* This drive uses mode select page 0xf for compression control;

* most of the other drives supporting compression use page 0x10 */

MTCAN_SILI|MTCAN_SEEK|MTCAN_CHTYPEANY|MTCAN_COMPRESS,

/* minimum delay on i/o is 12 minutes, to allow the Drives

* full error recovery sequence to be performed. */

40, 12*60, 12*60, 12*60, 512, 512*512, 0, (u_char *)0 },

2. For IRIX 6.x versions other than 6.4, make the following modification to the file /dev/

MAKEDEV.d/TPS_base (this modification is not required on systems running IRIX 6.4).

Locate the area of code that deals with DAT drives. This starts with:*

Drive?type:*DAT*

Insert the following before or after the similar entries for other supported devices:

*Device:*Python*PRTNO*) # DAT drive with compression

mdev=`expr $mdev + 8`;

mknod ${prf}$1c c ${C_TPS} $mdev;

;;

NOTE: TPS_base is a script, not a C source file. Using the C comment characters, /* */ and // causes the MAKEDEV script to fail and device drivers will not be created. Always use the shell comment character, #, in this file.

3. Rebuild the kernel, as described below.

See “Configuring Inquiry Strings” on page 27 for information about changing the inquiry string and replacing PRTNO with the number applicable to your DAT24 drive.

Rebuilding the Irix Kernel

1. Once the modifications are made, rebuild the kernel. This can be done using the autoconfig

command (see the autoconfig man page for details). Alternatively, Irix 5.3 and later detect the changes made and automatically rebuild the kernel the next time the system boots.

2. Once the new Kernel is built you will need to reboot the system again to bring the changes

into effect.

UNIX Settings Configuring for the HP-UX Workstation Environment

Troubleshooting Installation Problems on the SGI Platform

Checking the Drives Inquiry String

You can configure the DAT24 tape drive to return different inquiry strings. Consequently, before making the changes described in this chapter, it may be useful to check the drive’s inquiry string using the mt command. The following example retrieves the inquiry string and other status data from a DAT24 tape drive on SCSI bus 1, ID 4.

mt -f /dev/rmt/tps1d4 status

System Interchange Problems

If the following error appears when trying to restore a cpio archive from another system, a mistake has been made in the installation sequence above:

Byte swapped Data - re-try with correct device

If this error is encountered, it is probably caused by incorrect setup, as described above, Check and verify the correct modifications were made to /var/sysgen/master.d/scsi.

Switching Hardware Compression

Support for switching Hardware Compression is supported in Irix 6.x by using different device drivers. Drivers including a c in the device name should enable compression. Problems seen with compressed operation can be resolved by installing the latest Irix 6.x patch set.

Configuring for the HP-UX Workstation Environment

HP-UX Versions 10.2 and Later

1. Log in as root.

2. Run the SAM utility.

3. Choose the Peripheral Devices option.

4. Choose Tape Driv es.

5. From the Actions menu in the Tape Device Manager window, choose Add.

6. Within the Add a Tape Drive window, read the instructions, then click on OK.

7. SAM may detect that your HP-UX kernel lacks the drivers necessary to make use of the Tape

Drive. If so, read the message in the Device Driver Check window and choose the appropriate action. If you choose Build a new kernel and shut down the system immediately, SAM creates a new kernel and automatically reboots the system. After the system comes back up, the necessary drivers are loaded and the system can use the tape drive.

If you had to shut down the system to physically connect the tape drive, re-enter SAM and repeat steps 3 to 6.

8. Choose the new tape drive.

9. From the Actions menu, choose Create Device Files.

10. Press OK and exit SAM.

UNIX Settings Configuring for the IBM AIX Environment

Configuring for the IBM AIX Environment

AIX Versions 3.2 and Later

The DAT24 tape drive can be configured to work with AIX versions 3.2 and later by using the SMIT Other SCSI Tape Drive option. Record the SCSI ID of the tape drive before installing it.

To configure AIX using the SMIT utility, use the following procedure:

1. To enter SMIT at the Tape Drive menu, type smit tape.

2. Select Add a tape Drive.

3. Using the Other SCSI Tape Drive option, select the type of tape drive you will be adding.

4. Select the Parent SCSI Adapter from the available list

5. When the Add a Tape Drive Entry Fields appear, change some of the standard options

to maximize drive performance and functionality:

• Set the Connection Address with the Drives Target and Lun (always use

Lun 0). In the list, the Target is the first number and the Lun is the second. For example,

if the drive is ID 5, choose 5,0.

• Set the Fixed Blocksize to 1024.

• Set Density 1 to 140.

• Set the Maximum delay for the Read/Write command to 900.

6. Press the Return key to install the drive in the system database and create the devices.

7. Exit SMIT

AIX Device Drivers and Switching Data Compression

After you use SMIT to install the tape drive, device files are created for accessing the tape drive. Typical examples are:

/dev/rmt0 /dev/rmt0.1 /dev/rmt0. /dev/rmt0.3

/dev/rmt0.4 /dev/rmt0.5 /dev/rmt/0.6 /dev/rmt/0.7

With the configuration information provided here, devices rmt0, rmt0.1, rmt0.2, and rmt0.3 cause the drive to write in compressed mode. Using devices rmt0.4, rmt0.5, rmt0.6, and rmt0.7 causes the drive to write with compression disabled.

UNIX Settings Configuring for the SCO Environment

Configuring for the SCO Environment

The following versions of SCO UNIX that run on the PC platforms support the DAT24 drive using the standard switch settings (Switches 9 and 10 OFF).

SCO UNIX (including ODT and Open Server)

SCO UnixWare

Xenix

Once connected to the system, use the command mkdev tape install the drive. See the online manual pages for the mkdev command for specific installation details about each SCO variant.

Index

Flash codes 23

Cartridge

compatibility 22 initializing 21 loading 20 unloading 21

write-protecting 22 Cartridge Status LED 25 Cleaning tape heads 23 Compatibility of DAT cartridges 22 Configuration

desktop drive 18

internal drive 11 Connecting power cable

desktop drive 19

internal drive 17 Connecting SCSI interface cable

desktop drive 19

internal drive 17

DAT cartridge compatibility 22 DAT24

models 9

overview 9

unpacking 10 DAT24 desktop drive

configuration 18

connecting power cable 19

connecting SCSI interface cable 19

installation 18

SCSI ID 18 DAT24 internal drive

changing DIP switch settings 12

configuration 11

connecting power cable 17

connecting SCSI interface cable 17

DDS pass-through 13

guidelines and cautions 11

inquiry string 13, 27

installation 10

jumper settings 14

Media Recognition System 13

mounting 15

parity check 13

Power On Self Test 14

remote SCSI address selection 15

SCSI ID 12

SCSI termination 15

terminator power 15

UNIX operating systems 14, 26 DDS pass-through 13 DEC UNIX

Digital UNIX earlier than v4.0 29

Digital UNIX v4.0 and later 28 DEC UNIX environment 28 DIP switch settings, internal drive 12 Drive Status LED 25

Guidelines and cautions, internal drive 11

HP-UX environment 32

v10.2 and later 32

IBM AIX environment 33

v3.2 and later 33 Initializing a blank cartridge 21 Inquiry string 13, 27 Inspection 10 Installation

desktop DAT24 18

internal DAT24 10 Irix v5.x 30 Irix v6.x 31

Jumper settings 14

LED flash codes 23 LEDs

Cartridge Status 25

Drive Status 25 Loading a cartridge 20

Media Recognition System 13 Models 9 Mounting internal drive 15

in a 3.5-inch drive bay 15

in a 5.25-inch drive bay 16

Parity check 13 Power On Self Test 14

Remote SCSI address selection 15

SCO environment 34 SCSI ID

desktop drive 18

internal drive 12 SCSI termination

internal drive 15 Setting SCSI ID

desktop drive 18

internal drive 12 SGI environment 30

Irix v5.x 30

Irix v6.x 31

Solaris OS 2.x 30 Sun OS 4.1.x 29 Switches, internal drive 12

Tape heads, cleaning 23 Terminator power, internal drive 15

UNIX operating systems

DEC UNIX environment 28 Digital UNIX

earlier than v4.0 29 v4.0 and later 28

HP-UX environment 32

v10.2 and later 32 IBM AIX environment 33 IBM AIX v3.2 and later 33

SCO environment 34 SGI 30

IRIX v5.x 30

IRIX v6.x 31 Solaris 2.x 30 Sun OS 4.1.x 29 switch settings 14, 26

Unloading a cartridge 21 Unpacking 10

Write-protecting a cartridge 22

Certance DAT 24, 24 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual