Calx 36 Pendant
Installation Instructions
General Product information
This product is suitable for indoor dry and
damp locations only.
CAUTION - RISK OF FIRE
This product requires installation by a qualied
electrician. Before installing be sure to read
all instructions and TURN POWER OFF TO THE
JUNCTION BOX
Junction Box
3
Universal
Crossbar
8-32 x 3/4” Screw
Adjusting the Fixture Height
1
Measure the desired height (H) that you want
the xture to hang below the ceiling.
2
Adjust the length of the suspension cables
to roughly the desired length by pushing
them into the side-exit cable grippers. Final
adjustments can be made after the xture is
mounted.
Mounting the Fixture
3
Attach the universal crossbar to the junction box using the
supplied 8-32 x 3/4” screws.
Pull line voltage wires through crossbar. Feed the clear power cord
4
through the strain relief hole in the canopy and make connections
between line voltage wires and power cord.
Figure 1
1
H
Black (hot)
Smooth (hot)
Junction Box
4
Yellow Wire Nut
Yellow Wire Nut
Ribbed (Neutral)
White (Neutral)
Strain Relief Hole
8-32 x 1.75” Screw
Power Cord
Suspension Cable
Side-Exit
Cable Gripper
2
7
CERNOGROUP.COM T_949.715.1534
1751 MCGAW AVE, IRVINE, CA 92614
COPYRIGHT 2016 CERNO LLC.
Calx 36 Pendant
Installation Instructions
5
8
6
5
After electrical connections have been made, place wire
connections and excess wire into the junction box.
6
Fasten the canopy to the universal crossbar using the included
#8-32 x 1.75” screws.
Leveling the Fixture
Level the xture by making small adjustments to the length
7
of each suspension cable. Pressing the small cylindar on top
of the side-exit cable grippers will release the grip on the
suspension cable.
8
Once the xture is set at the correct height and is leveled,
squeeze the black strain relief onto the clear power cord and
press into the strain relief hole in the canopy. Once properly
installed, the power cord should be held tightly and can not
be pulled from the canopy.
Installing the Bulbs
9
Once the xture is suspended and leveled, install the GU-24
base bulbs (not included) into the four GU-24 sockets within
the xture.
Securing the Canopy
Figure 3
CERNOGROUP.COM T_949.715.1534
1751 MCGAW AVE, IRVINE, CA 92614
COPYRIGHT 2016 CERNO LLC.
Calx 36 Pendant
Installation Instructions
Care, maintenance instructions
Regularly maintaining your Cerno® product is easy and will help keep it looking beautiful. Scratches can be bued out in minutes. Wood surfaces
will be revitalized with minimal eort every few years. The LED light source is rated to last 50,000 hours, and should last the life of the product.
Your pendant may include materials listed below. Please use these tips to keep your product looking its best.
Wood Finishes: Wood surfaces should be dusted and cleaned with a damp cloth.
Metal Finishes: Everyday cleaning of metal surfaces can be done with a damp cloth.
Polymer: To clean polymer surfaces, use a damp cloth with soap and water or typical cleaners. Avoid heavy-duty cleaners (i.e. anything solventbased), as they can damage the material. Repair: Scratches can be bued out of polymer surfaces using 200 - 300 grit sandpaper.
Cerno’s mission since the company's inception has been to fuse quality, performance and resource eciency with contemporary design.
Producing environmentally responsible products involves far more details than merely guaranteeing your products energy ecient performance and maintaining
eco conscious manufacturing practices. We live in a consumer age characterized by excess and waste, where nearly everything we posses is viewed as disposable,
from the cars we drive to the bottle of water you are drinking right now.
At Cerno we aim to provide our customers an opportunity to purchase objects of value to enhance their built environment. We construct our products with
integrity that will pass the test of time with the goal of evading a premature trip to the local landll. All the products are assembled by human hands and endure
rigorous testing to assure that our exceptionally high standards of quality are always satised.
Warranty
In addition to our two year product defect warranty, Cerno oers a repair service for the life of your product. Every Cerno product is designed and manufactured
in the United States which facilitates excellent quality control and easy access to our engineers and service technicians. At Cerno we pride ourselves on delivering
products executed with an unparalleled level of craftsmanship. For any reason should our customers have an issue with their orders upon delivery we will repair or
replace the item.
In addition to our warranty and quality guarantees, Cerno welcomes customer feedback so please e-mail all comments to info@cernogroup.com
CERNOGROUP.COM T_949.715.1534
1751 MCGAW AVE, IRVINE, CA 92614
COPYRIGHT 2016 CERNO LLC.
Loading...