Cerio CS Series, CS-1224G Quick Installation Manual

CS-Series CS-1224G

•

Note: If any of these items is found missing or damaged, please contact your local supplier for replacement.

FCC Warning

24 Port 10/100/1000M Gigabit Switch

with 2 SFP Ports

Quick Installation Guide

User’s Guide

Package Contents

Before you start to install this switch, please verify your package that contains the following items:

CS-1224G Main Unit x1 19" Rack Mount Kit x1 Quick Installation Guide x1 Power Code x 1 Warranty Card x 1

Product Features

• Complying with IEEE 802.3 10Base-T, IEE 802.3u 100Base-TX,

• 24 Port 10/100/1000Mbps TX Auto-Negotiation Ethernet Switch

• Supports 2 Gigabit SFP Fiber uplink ports for IEEE 802.3z

• Supports Energy-Efficient Ethernet (EEE), IEEE 802.3az

• Supports Green Ethernet features, Link-On and Cable Length

• Supports auto-detection for SFP ports/mini GBIC module

• Half/Full-Duplex capability on each TX port Auto-learning

• Supports Store & Forward architecture and performs forwarding

• IEEE802.3x flow control for Full-duplex, Back Pressure function

• Provides 9K Jumbo frames to improve network utilization of large

• Non-blocking & Non-head-of-line blocking full-wire speed

• Supports TP interface Auto MDIX function for auto TX/RX swap

• Automatic Source MAC Address Learning and Aging

• Supports up to 8K MAC addresses

• Up to 4.1 Mbit buffer memory

CS-1224G ：Dimensions 441 x 131 x 44 (19 inch)

IEE 802.3ab 1000Base-T, IEEE802.z 1000Base-X, IEEE802.3az specifications

1000Base-SX/LX

standards

Power Saving, Link-Down Power Saving, Power saving mode support to automatic cable detection

insertion

networking configurations

and filtering

for Half-Duplex operation

file transfers

forwarding

This device has been tested and found to comply with limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the user’s manual, it may cause interference in which case users will be required to correct interference at their own expenses.

CE Warning

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Introduction

The CERIO CS-1224G is a 10/100/1000Mbps 24 port Gigabit Ethernet Switch that utilize 2 Gigabit SFP uplink

ports. The CERIO CS-1224G case is designed for small

offices, and can be optionally upgrade to 1U” chassis. The CS-1224G is ideal for micro-segmenting large networks into

smaller networks, connecting subnets for improved performance, and enabling the bandwidth demanded for multimedia and imaging applications. Moreover, the

10/100/1000Mbps Auto-Sensing ability provides an easy way to migrate Gigabit network without pain. By integrating both

data transmitting cable and power cord, the hassle of constructing your network can be eliminated, allowing you to easily connect your wired LAN network. The CERIO

CS-1224G defines new green power saving idea in all Port, incorporating an on/off button to enable or disable the IEEE802.3az function. The CS-1224G can solve the limitation of the network local LAN and offer the system relocation easily.

Plug & play and all kinds of network protocols compilation make the installation of the device both simple and quick. With auto-MDI/MDI-X support, there is no need for any Crossover cables when you connect the device to a computer, or even another switch, In addition, the auto-negotiation function auto-senses and adjusts the connected devices whether they are running at 10 Mbps, 100Mbps, or 1000Mbps.

The CS-1224G also supports Low Power Idle Mode. When Low Power Idle Mode is enabled, systems on both sides of the link can disable portions of functionality and save power during periods of low link utilization, reducing power consumption up to 81%. With its non-blocking architecture, the CERIO CS-1224G Green Ethernet switch receives and forwards traffic seamlessly. Duplex mode also doubles the bandwidth by enabling two-way communication. Every port simultaneously supports up to 2Gbps of bandwidth for all 26 ports, totaling up to 52Gbps of switching capacity to a shared total 10/100/1000

Power Consumption

CS-1224G 4.7 Watts

Dimension & Weight :

CS-1224G 441 x 131 x 44 mm (19 inch)

This switch can be easily installed on a desktop or rack and allow

Attach the Rubber feet provided with the switch to ensure

6. Reconnect all the cables

Media

Speed(Mbps)

Cable Type

Category 3, 4, 5 UTP/STP

Category 5e, 6 UTP/STP

Mini GBIC required

came with purchase

IEEE 802.3 10Base-T

Method: Store and Forward

Forwarding Rates

10Mbps – 14,880pps

1000Base TX Cat 5e, 6 UTP/STP

Per Unit: Power

Power Input

100~240V/AC, 50~60Hz

Dimensions

CS-1224G : 441 x 131 x 44 (19 inch)

Operating Temperature

0 to 50℃

Storage Temperature

-40 to 70℃

Humidity

5 to 90% RH (non-condensing)

Certifications

FCC , CE Class A

Front Panel (LEDs)

LED Indicators of 26 port 10/100/1000Mbps Switch

LED Status Description

Power

LINK/ACT

On Power is on.

Off Power is off.

On Port is for connection.

Off No connection.

Flashing Data is transmitting or receiving

Desktop / Rack Installation

easy device access for connecting cables and to the power button. A minimum of 25mm around the device is recommended for product safety.

Desktop Installation

Rack Installation

The CS-1224G can be mounted on a standard 19” rack to allow for convenient placement and device safety. The switch is supplied with rack mounting brackets and screws for optional installation.

Required Mounting Materials

Mounting Procedure

minimal movement of the device

2. Keep the switch away from devices such as radios, broadband amplifiers, and other transmitters that might cause signal interferences

3. Distancing the device from moisture is also highly recommended

1. Two mounting brackets

2. 6 M3 flathead screws

1. Disconnect all cables from the device

2. Place device on a hard surface, the front of the device must be facing you.

3. Locate mounting holes on the sides of the unit

4. Install mounting brackets using M3 flathead screws on both sides of the device

5. Place unit onto the rack and secure with proper screws

Network Cable Configurations

All of CS-1224G Ports support MDI/MDI-X functionality. The device supports both straight-through and crossover cables which can link the switch to PCs, Hubs, Switches, and Routers. To make a valid connection and obtain optimal performance using appropriate cabling, please refer to the table below.

10/100/1000Mbps Copper

1000Mbps Fiber (Mini GBIC required)

100 Category 5 UTP/STP

1000

differs from one that

Rear Panel (Power)

AC input

AC input (100~240V/AC, 50~60Hz)

Technical Specifications

IEEE 802.3u 100Base-TX,

Standards

Features

Filtering/

Transmission Media

LED Indicators

IEEE 802.3x Flow Control IEEE 802.3ab 1000Base-T IEEE 802.3z 1000Base-X IEEE802.3az Energ y-Efficient-Ethernet

Number of Ports: 26 P orts MAC Address: 8K Buffer Memory: 4.1Mbit

100Mbps port – 148,800pps

10BaseT Cat. 3, 4, 5 UTP/STP 100BaseTX Cat. 5 UTP/STP

Per Port: LINK/ACT