MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the
original purchaser that each new MILLER wrecker or other MILLER products will be free from defects
in material and workmanship for a period of twelve (12) months from date placed in service, but in no
event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER.
The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no
event shall MILLER accept such notication later than twenty-four (24) months from date of delivery or
twelve (12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement
at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will
be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does
not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair
or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY,
EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of
prots or goodwill, or any other special, incidental, indirect, or consequential damages concerning or
relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach
of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from
any general or particular requirement which MILLER knew or had reason to know about at the time
of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be afxed or
any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR
PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such
warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted
under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the following
items, which are set forth by way of example and not limitation:
A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs,
failure to provide reasonable and necessary maintenance, or uses for which the equipment
was not designed or intended.
C. Alterations or modications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
aps, fenderettes, light bulbs, hydraulic oil, lters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
SERIAL NUMBERMiller Industries Towing Equipment Inc.
8503 Hilltop Drive
This Section is provided by the manufacturer for the purpose of ordering any
component part of the CENTURY EB-4 / EXPRESS that may be required
when part replacement is necessary . Be certain to use only original equipment
replacement parts for warranty purposes as well as for keeping your
CENTURY EB-4 / EXPRESS in its original state and optimum operating
capacities.
When ordering replacement or spare parts be sure to provide the following
information to the manufacturer’s Parts Department.
1. Manual Number & Date of Publication
2. Manual Page Number
3. Page Title
4. Reference Number of Part Desired
5. Part Number
6. Part Description
7. Quantity of Part Desired
Providing this information will help ensure that the correct parts will be delivered
to you in an expedient manner without delay . Should additional information
be required for repair or replacement of certain components, contact your
Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability .
VI-1
Page 4
Section VI - PARTS LIST (cont'd)
REF .PARTNO.
NO.NUMBERDESCRIPTIONREQ'D
--120015412CENTURY EB4T W/EXPRESS CROSSBAR 84/90
10302080HARNESS SWITCH P ANEL1
20302122SWITCH PANEL HOT WIRE1
3030322680 A MP CIRCUIT BREAKER1
40303880REMOTE CONTROL HANDLE2
50303883WINCH CABLE ASSEMBL Y2
60500971DA T A PLA T E - EB4/6500 CENTURY1
70714948SUCTION HOSE, 1" 16C4 10 FT .1
--0901496KI T - CENTUR Y NAMEPLA TE1
--0903069KIT - BACK UP ALARM1
--0903275KIT - SAFETY CHAIN F65001
--0903284KIT - DAYTONA BOX1
--0903295KIT - CONTROL KNOB1
--0904103KIT - ELECTRICAL TERMINAL1
--0904782KIT - STINGER POSITIONING1
--0904799BODY ASSEMBLY 84CA/90W DUAL1
--AWS-1000-ATIE DOWN STRAP ASSEMBL Y2
--0901496KI T - CENTUR Y NAMEPLA TE
80400035#10-24 X 1/2" OVAL HD SS6
90500406NAMEPLA TE, CENTURY2
--0903069KIT - BACK UP ALARM
100300077WIRE, 16 GA, RED2 FT.
110300153CONNECTOR, WIRE (BLUE)6
120301812HEAT SHRINK TUBE-IN.MELT1
130303061BACK UP ALARM ECCO #MS971
1404000571/4"-20 X 1-1/4" HHCS2
1504003671/4"-20 NYLOK HEX NUT ZP2
160500676INST ALLA TION INSTRUCTIONS - BACKUP ALARM1
2103008443/4" X 1/8" CLOSED CELL25 FT.
220302855TOOL CMPT LATCH PLAIN4
230303993STRIKER BOL T4
240400021#8-32 X 1/2" RDHD PH MCH SC SS16
250400351#8-32 HEX NUT & ST AR W ASHER ZP16
VI-2
Page 5
Section VI - PARTS LIST (cont'd)
REF .PARTNO.
NO.NUMBERDESCRIPTIONREQ'D
--0902798KIT - CONTROL KNOB
260300834KNOB - CTRL (IN-OUT)4
270300835KNOB - BOOM (UP-DOWN)2
280300837KNOB - BOOM (IN-OUT)2
290302856KNOB - TIL T, 3/8"-16 THREAD2
300302917KNOB - WHEEL LIFT EXTEND (IN-OUT)2
310303283KNO B - CLA W (OPEN-CLOSE)2
3204003933/8"-16 HEX NUT JAM ZP14
--0904103KIT - ELECTRICAL TERMINAL
3303014761/4" BLADE CONN, PIGGYBACK24
340301503#10 RING CONN.10
350302423TERMINAL, 1/4" RING 14-16GA 4
--0904782KIT - STINGER POSITIONING
3604002381/2"-13 X 1-1/2" SKT HD CP SC2
3704003781/4"-20 X 1" FL PHIL HD4
3804004081/2"-13 NYLOK HEX NUT2
390501002INST ALLA TION INSTRUCTIONS1
400709110CLAMP ADJUSTMENT BLOCK2
410709111SPACERS - ADJUSTING6
420713131SHEAR BLOCK1
430804106STINGER POSITIONING BRACKET WELDMENT1
--0904783RETAINER PIN ASSEMBL Y
450400579SPRING PIN, 3/8" X 4"1
460714507RETAINER PIN1
--0904799BODY ASSEMBLY 84CA/90W DUAL
470300032PLUG , 1" DIA HOLE1
480300071CLAMP, HOSE, 1" IDEAL2
490300113GREASE FITTING , ALEMITE1
500300329SNAP RING, EXTERNAL 2"2
510300787HOSE ASSEMBL Y , 53"1
520301334CATERPILLER GROMMET , 1/2"1
530301471HOSE ASSEMBL Y , 30"1
540301473HOSE ASSEMBL Y , 18"1
550301533TIE DOWN STRAP , 15"1
560301659HOSE ASSEMBL Y , 150"1
570302171PLUG , 3/4"-16 PLASTIC1
580302552C-WA-10 WELD ADAPTER4
VI-3
Page 6
Section VI - PARTS LIST (cont'd)
REF .PARTNO.
NO.NUMBERDESCRIPTIONREQ'D
--0904799BODY ASSEMBLY 84CA/90W DUAL (cont'd)
590302610HOSE ASSEMBL Y , 36"1
600302855TOOL COMPT LATCH PLAIN1
610302926HOSE ASSEMBL Y , 29"5
620303014HOSE ASSEMBLY, 1/2" DIA 80"4
630303193BLACK SKUFF JACKET #SJ1620 FT .
640303481SLIDE P AD - BUMPER3
650303863HOSE ASSEMBL Y , 170"2
660304264TOOL BOX HINGE2
670400002#4 X 1/4" DRIVE SCREW RD HD4
680400021#8-32 X 1/2" RD HD PH MCH SC SS4
6904000621/4"-20 X 3/4" THRD CUT HEX2
7004000701/4"-20 X 1" HHCS GR5 ZP4
7104000781/4"-20 X 2" HHCS GR5 ZP1
7204001185/16"-18 X 3/4" HHCS GR5 ZP4
7304001223/8"-16 X 1-1/4" HHCS GR5 ZP2
7404001543/8"-16 X 1/2 HHCS GR5 ZP2
7504002233/8"-16 X 3/4" FL HD6
7604002391/2"-13 X 3/4" HHCS GR52
7704002495/8"-1 1 X 1-1/4" SOC HD CAP SCREW8
7804002645/8"-1 1 X 2-1/4" HHCS GR5 ZP12
790400351#8-32 HEX NUT & ST AR W ASHER ZP4
8004003825/16"-18 NYLOK HEX NUT ZP4
8104003983/8"-16 NYLOK HALF-NUT ZP24
8204004215/8"-1 1 NYLOK HEX NUT ZP12
8304004511/4" FLA TW ASHER ZP4
8404004521/4" HELICAL LOCKWASHER ZP8
8504004823/8" HELICAL LOCKWASHER ZP2
8604005085/8" HELICAL LOCKWASHER ZP8
8704005671/4" RIVET BTT 84 SS4
880400579SPRING PIN, 3/8" X 4" ZP2
890701956SCREW , OUTER CROSSTUBE RET , FI4
900703640WASHER, THRUST (NYLATRON)2
910708529HOSE, RETURN 3/4" I.D. X 36"1
910708931ACCESS COVER1
920713913SHAFT , BOOM PIVOT - EB41
930801952LEG, SHIPPING2
940803906BOOM TRUNION PIVOT2
950803919TUBE, HOSE WELDMENT1
960803947BODY WELDMENT1
970803957TUBE, BOOM HOSE WELDMENT1
--0901479VALVE, SHUTTLE ASSEMBL Y1
--0902182KIT - INLINE FILTER1
VI-4
Page 7
Section VI - PARTS LIST (cont'd)
REF .PARTNO.
NO.NUMBERDESCRIPTIONREQ'D
--0904799BODY ASSEMBLY 84CA/90W DUAL (cont'd)
--0902721KIT - HYDRAULIC TANK1
--0902949IN-CAB CONTROL HYDRAULIC KIT1
--0904171SWIVEL ASSEMBL Y , BOOM END1
--0904520KIT - VALVE1
--0904521KIT - SOLENOID1
--0904534TENSIONER, HOSE ASSEMBLY1
--0904539KIT - SPLASH GUARD FT1
--0904595CYLINDER - LIFT ASSEMBLY1
--0904598CROSSBAR ASSEMBLY, MED DUTY1
--0904609KIT - CONTROL DUAL1
--0904798WKR & W/L LESS CROSSBAR DUAL1
98CZ15RUBBER GROMMET , 1/2"3
99DE17165/32" X 1/4" DOME HEAD4
--0901479VALVE, SHUTTLE ASSEMBL Y
1000300142FITTING, ELB 6MJ-4MP901
1010301424FITTING, MALE CONNECTOR 6MJ-4MP2
1020301868FITTING, MALE RUN TEE 4FP-4FP-4MP2
1030302053FITTING, STRAIGHT 8MJ-4MP2
1040302226VALVE, SHUTTLE1
10504000901/4"-20 X 1-3/4" RD HD GR5 ZP2
10604004521/4" HELICAL LOCKWASHER ZP2
--0904598CROSSBAR ASSEMBLY, MED DUTY
1520303860HOSE ASSEMBLY , 10"1
1530303861HOSE ASSEMBLY , 17"1
1540303886PLUG 4MB2
1550303911CYLINDER, MED DUTY EXPRESS2
1560303917BEARING, MED DUTY EXPRESS2
15704003493/8"-16 X 3/4" FLT SKT HD2
17104004275/8"-11 HEX JAM NUT ZP2
15804004285/8"-11 FLEXLOC THIN HIGH2
15904005461/8" X 1-1/4" COTTER PIN2
16004005905/8" X 1-1/4" CLEVIS PIN2
1610714030PIN, CYLINDER, MED DUTY EXPRESS2
1620714521BOLT, PIVOT PIN (EXPRESS)2
1630803949ADAPTER, TIRE WELDMENT2
1640803956CROSSBAR WELDMENT, MED DUTY1
1650803958ARM, LEFT L WELDMENT , MED DUTY1
1660803959ARM, RIGHT L WELDMENT , MED DUTY1
1670803963PIN WELDMENT, L ARM T O CROSSBAR2
1680804069PIVOT PIN WELDMENT, EB4 EXPRESS1
169HC1291FITTING, 4MJ-4MB STR THR6
170HD01061/4" X 1-3/4" SPRING PIN ZP2
--0904609KIT - CONTROL DUAL
1600300122GROMMET, SPLIT PLASTIC21
16104000661/4"-20 X 3/4" HHCS GR5 ZP6
16204003701/4" “U” TYPE TINNERMAN6
16304003903/8"-16 HEX JAM NUT14
16404003923/8"-16 NYLOK HEX NUT ZP7
16504003933/8"-16 HEX NUT JAM ZP21
16604004521/4" HELICAL LOCKWASHER ZP6
16704005275/16" X 5/8" CLEVIS PIN7
16804005423/16" X 1-1/4"COTTER PIN SS14
16904005431/8" X 3/4" COTTER PIN7
1700701099ROD, CONTROL7
1710703501ANGLE, CROSS CONTROL1
1720704517CHANNEL, X-ROD BEARING2
VI-8
Page 11
Section VI - PARTS LIST (cont'd)
REF .PARTNO.
NO.NUMBERDESCRIPTIONREQ'D
--0904609KIT - CONTROL DUAL (cont'd)
1730705494LEVER, CONTROL14
1740713483CROSSROD, WRECKER FI4
1750713484CROSSROD, WHEEL LIFT FI3
1760800604ARM, CONTROL7
1770801309SHIFTER, VALVE, SHORT2
1780801310SHIFTER, VALVE, MEDIUM3
1790801311SHIFTER, V AL VE, LONG2
--0904798WRECKER & W/L LESS XBAR DUAL
1880300044FITTING, CONNECTOR 6MJ-8MB2
1890300110SNAP RING, 1"4
1900300113GREASE FITTING, ALEMITE8
1910300679BEARING PAD, NYLATRON4
1920301376FITTING, CONNECTOR 8MJ-10MB4
1930301921HOSE ASSEMBLY , 128"2
1940301964HOSE ASSEMBLY , 65"1
1950301965HOSE ASSEMBLY , 131"1
1960302469MOTOR, CHAR-L YNN2
1970302919CYLINDER HYD FOLD1
1980302922HOSE ASSEMBLY , 170"2
1990303067SLIDE PAD - INNER BOOM1
2000303068SLIDE PAD - OUTER BOOM1
2010303550CYLINDER HYD EXTEND - SWRK1
2020303852WINCH ASSEMBLY - NARROW DRUM1
2030303853WINCH ASSEMBLY - NARROW DRUM1
20404000601/4"-20 X 1/2" HHCS GR5 ZP3
20504000661/4"-20 X 3/4" HHCS GR5 ZP2
20604000701/4"-20 X 1" HHCS GR5 ZP2
20704001293/8" X 3/4" ALLEN HD SET1
20804001393/8"-16 X 1-1/2" HEX SKT SET1
20904002347/16"-14 X 1-1/4" HHCS GR5 ZP8
21004003533/8" X 1/2" SET SCR W/P A TCH1
21104003671/4"-20 NYLOK HEX NUT ZP6
21204003767/16"-14 X 2" HHCS GR5 PL8
21304003933/8"-16 HEX NUT JAM ZP2
21404003983/8"-16 NYLOK HALF-NUT ZP2
21504004511/4" FLATWASHER ZP6
21604004521/4" HELICAL LOCKWASHR ZP4
21704004803/8" FLATWASHER ZP12
21804004877/16" HELICAL LOCKWASHER16
21104005931/4"-20 X 1/2" SKT FL HD6
2190703082PIN, EXT CYL PIVOT1