Century Falcon 4D Plus Series, CFD-4206P, CFD-4304P User Manual
User’s Manual
Falcon 4D Plus Series
FCC COMPLIANCE STATEMENT
FOR AMERICAN USERS
This equipment has been tested and found to comply with the limits for a CLASS A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at own expense.
EMS AND EMI COMPLIANCE STATEMENT
FOR EUROPEAN USERS
This equipment has been tested and passed with the requirements relating to electromagnetic
compatibility based on the standards EN 55022:1998+A1:2000+A2:2003, CISPR 22 , Class A
EN 55024:1998+A1:2001+A2:2003, IEC 61000- 4 Series EN 61000-3-2 / 2000 & EN 61000-3-3 /
1995. The equipment also tested and passed in accordance with the European Standard
EN55022 for the both Radiated and Conducted emissions limits.
FALCON PLUS SERIES
TO WHICH THIS DECLARATION RELATES
IS IN CONFORMITY WITH THE FOLLOWING STANDARDS
EN55022 : 1998,CLSPR 22, Class A / EN55024 : 1998IEC 61000-4 Serial / EN61000-3-2 : 2000
/ EN 6100-3-3 : 1995 / CFR 47, Part 15/CISPR 22 3rd Edition : 1997, Class A / ANSI C63.4 :
2001 / CNS 13438 / IEC60950-1 : 2001 / GB4943 : 2001 / GB9254 : 1998 / GB17625.1 : 2003
/EN60950-1 : 2001
CAUTION
Danger of explosion if battery is incorrectly replaced
Replace only with the equivalent type recommended by the manufacture.
Dispose of used batteries according to the manufacturer’s instructions.
Specifications are subject to change without notice.
Falcon 4D Plus User’s Manual
1
Safety Instructions
Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.
1. Die Geräte nicht der Feuchtigkeit aussetzen.
2. Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dass die
Spannung des Geräts mit der Netzspannung übereinstimmt.
3. Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerät könnte
sonst Schaden nehmen.
4. Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort den
Netzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichen elektrischen
Schlags.
5. Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur von
autorisierten Personen durchgeführt werden.
6. Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften der
zuständigen Berufsverbände und Behörden unbedingt eingehalten werden.
7. Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls die
zuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust der
Versicherungsleistungen führen.
Falcon 4D Plus User’s Manual
2
Safety Instructions
Please read the following instructions seriously.
1. Keep the equipment away from humidity.
2. Before you connect the equipment to the power outlet, please check the voltage of the
power source.
3. Disconnect the equipment from the voltage of the power source to prevent possible
transient over voltage damage.
4. Don’t pour any liquid to the equipment to avoid electrical shock.
5. ONLY qualified service personnel for safety reason should open equipment.
6. Don’t repair or adjust energized equipment alone under any circumstances. Some one
capable of providing first aid must always be present for your safety
7. Always obtain first aid or medical attention immediately after an injury. Never neglect
an injury, no matter how slight it seems.
Falcon 4D Plus User’s Manual
3
1. BARCODE PRINTER...................................................................5
1-1. Printer Accessories.........................................................................................................5
1-2. General Specifications....................................................................................................5
1-3. Communication Interface................................................................................................7
1-4. Printer Parts....................................................................................................................9
2. PRINTER INSTALLATION......................................................... 11
2-1. Ribbon Installation ........................................................................................................11
2-2. Label Installation...........................................................................................................13
2-3. Label Roll Core Installation Instruction.........................................................................14
2-4. Card / Hang tags Installation ........................................................................................15
2-5. PC Connection..............................................................................................................15
2-6. Driver Installation.......................................................................................................... 16
3. ACCESSORY............................................................................. 17
3-1. Stripper Installation....................................................................................................... 17
3-2. Cutter Installation..........................................................................................................20
3-3. CF Card Adapter Installation.........................................................................................22
3-4. CF Card Instruction....................................................................................................... 23
4. CONTROL PANEL.....................................................................24
4-1. LED Status....................................................................................................................24
4-2. FEED Key.....................................................................................................................25
4-3. Self-Test........................................................................................................................ 25
4-4. Auto Sensing................................................................................................................. 26
4-5. Dump Mode ..................................................................................................................26
4-6. Direct Thermal / Thermal Transfer Mode Switch.......................................................... 26
4-7. See-through Sensor on/off............................................................................................ 27
4-8. Error Messages.............................................................................................................28
5. MAINTENANCE AND ADJUSTMENT....................................... 29
5-1. Thermal Print Head Cleaning .......................................................................................29
5-2. Thermal Print Head Balance Adjustment......................................................................29
5-3. Print Line Adjustment.................................................................................................... 30
5-4. Adjust the cutter............................................................................................................30
5-5. Troubleshooting............................................................................................................ 31
Falcon 4D Plus User’s Manual
4
1. Barcode Printer
1-1. Printer Accessories
After unpacking, please check the accessories that come with the package, and store
appropriately.
Barcode printer
Power cord
Switching Power
USB Cable
Label
Ribbon
Empty Ribbon Roll
Clean card
Quick Start Guide
CD (includes label editing software CLabel / Manual)
1-2. General Specifications
Model Falcon 4D Plus (CFD-4206P) Falcon 4D Plus (CFD-4304P)
Resolution
203 dpi (8 dot/mm) 300 dpi (12 dot/mm)
Print Mode
Thermal Transfer / Direct Thermal
CPU
32 Bit
Memory
4MB Flash, 8MB SDRAM
Print Speed
2 IPS ~ 6 IPS 2 IPS ~ 4 IPS
Print Length
Min 12mm (0.47”),
Max 1727mm (68”)
Min 12mm (0.47”),
Max 762mm (30”)
Print Width
108 mm (4.25”) 105.7mm (4.16”)
Sensor Type
Adjustable Reflective sensor; Fixed transmissive, center aligned
Sensor Detection
Type: Label gap and black mark sensing.
Detection: Label length auto sensing and / or program command setting
Media
Label Roll OD: Max. 125mm (4.92”)
Core Diameter: 1”, 1.5”, 3”
Width: 25mm (1 “) ~ 118mm (4.64”)
Thickness: 0.06~0.25mm (0.0025”~0.0098”)
Ribbon
Length: 300M (981 ft)
Max. ribbon roll OD: 68mm (2.67 “)
Type: transfer ribbons (wax, hybrid, and resin) in widths of 30mm to 110mm
(1.88” to 4.33”)
Core Inner Diameter: 25.4mm (1”)
Printer Language
EZPL (Firmware downloadable)
Software
Application: CLabel-IV(EZPL only)
DLL & Driver: Microsoft Windows NT 4.0, 2000 and XP
Resident Fonts
11 resident Windows bit mapped fonts (6,8,10,12,14,18,24,30,16X26,OCR A &
B); can be rotated in 8 orientations and expandable 8 times horizontally and
vertically. Scalable Font in 4 orientations.
Fonts Download
Windows bit mapped font: can be rotated in 8 orientations and expandable 8
times horizontally and vertically.
Asian font: can be rotated in 4 orientations and expandable 8 times horizontally
and vertically.
True Type Font: can be rotated in 4 orientations.
Image Handling
Support BMP and PCX. Support ICO, WMF, JPG, EMF file through software.
Support image resize, rotating, mapping and inverse through software.
Barcodes
Code 39, Code 93, Code 128 (subset A, B, C), UCC/EAN-128 K-Mart,
UCC/EAN-128, UPC A / E (add on 2 & 5), I 2 of 5, I 2 of 5 with Shipping Bearer
Bars, EAN 8 / 13 (add on 2 & 5), Codabar, Post NET, EAN 128, DUN 14,
MaxiCode, HIBC, Plessey, Random Weight, Telepen, FIM, China Postal Code,
RPS 128, PDF417, Datamatrix code & QR code
Falcon 4D Plus User’s Manual
5
Interfaces
Serial port: RS-232 ( Baud rate : 4800 ~ 115200 , Xon/Xoff , DSR/DTR )
USB port: V2.0
Parallel port: Bi-direction
Control Panel
Two Bi-color LED: Ready, Status
Function Key: FEED
Power
Auto Switching 100/240VAC, 50/60 Hz
Environment
Operation: 41°F to 104°F (5°C to 40°C)
Storage: -4°F to 122°F (-20°C to 50°C)
Cert. Approval
CE, FCC Class A, CCC, CB, cUL, BSMI
Humidity
Operation: 30-85%, non-condensing. Free air.
Storage: 10-90%, non-condensing. Free air.
Printer Dimension
Length: 285 mm (11.2”)
Height: 171 mm (6.8”)
Width: 226 mm (8.9”)
Weight: 2.72 Kg
Options
Rotary Cutter Module
Stripper Module
CF Card Adapter with RTC
Internal Ethernet Adapter Card
Specifications are subject to change without notice.
Falcon 4D Plus User’s Manual
6
1-3. Communication Interface
Parallel Interface
Handshake : DSTB connects to the printer, BUSY connects to the host
Interface cable : Parallel cable compatible to IBM PC
Pin out : See below
PIN NO. FUNCTION TRANSMITTER
1
2-9
10
11
12
13
14
15
16
17
18
19-30
31
32
33
34-35
36
/Strobe
Data 0-7
/Acknowledge
Busy
/Paper empty
/Select
/Auto-Linefeed
N/C
Signal Gnd
Chasis Gnd
+5V,max 500mA
Signal Gnd
/Initialize
/Error
Signal Ground
N/C
/Select-in
host / printer
host
printer
printer
printer
printer
host / printer
host
host / printer
printer
host / printer
Serial Interface
Serial Default
Setting
:
9600 baud rate､no parity､8 data bits､1 stop bit､XON/XOFF protocol and
RTS/CTS。
RS232 HOUSING (9-pin to 9-pin)
DB9 SOCKET DB9 PLUG
--- 1 1 +5V,max 500mA
RXD 2 2 TXD
TXD 3 3 RXD
DTR 4 4 N/C
GND 5 5 GND
DSR 6 6 RTS
RTS 7 7 CTS
CTS 8 8 RTS
RI 9 9 N/C
PC
PRINTER
【
Note】The total current output from parallel port and serial port altogether can not exceed
500mA.
USB Interface
Connector Type : Type B
PIN NO. 1 2 3 4
FUNCTION VBUS D- D+ GND
Falcon 4D Plus User’s Manual
7
Internal Interface
UART1 wafer Ethernet module
N.C
1
1
N.C
TXD
2
2
RXD
RXD
3
3
TXD
CTS
4
4
RTS
GND
5
5
GND
RTS
6
6
CTS
E_MD
7
7
E_MD
RTS
8
8
CTS
E_RST
9
9
E_RST
+5V
10
10
+5V
GND
11
11
GND
+5V
12
12
+5V
UART2 wafer Expansion module
+5V
1
1
+5V
CTS
2
2
RTS
TXD
3
3
RXD
RTS
4
4
CTS
RXD
5
5
TXD
GND
6
6
GND
Falcon 4D Plus User’s Manual
8
1-4. Printer Parts
2
1
3
4
5
6
7
8
1. Cover Open Button
2. Top Cover
3. Label Roll Core
4. Ribbon Rewind Wheel
5. Print Mechanism
6. Ribbon Rewind Shaft + Empty Ribbon Roll
7. Locking Tenon (left/right)
8. Front Cover Piece
2
1
3
4
5
1. LED Light (Ready)
2. LED Light (Status)
3. FEED Key
4. CF Card Slot Cover
5. Print Head Pressure Adjustment Screw (left/right)
Falcon 4D Plus User’s Manual
9
Loading...