Page 1
HEAVY DUTY AIR OSCILLATING
Model
96573
SANDER
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Page 2
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in
the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
IMPORTANT SAFETY INFORMATION
In this manual, on the labeling, and all other information
provided with this product:
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER
WARNING
CAUTION
Notice
CAUTION
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
CAUTION, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
NOTICE is used to address practices not
related to personal injury.
CAUTION, without the safety alert symbol,
is used to address practices not related to
personal injury.
Page 2SKU 96573 For technical questions, please call 1-800-444-3353.
Page 3
WARNING! Read all instructions
Failure to follow all instructions listed below may result in serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
1. Keep children and bystanders away while operating. Distractions can
cause you to lose control.
2. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
PERSONAL SAFETY
1. Wear ANSI-approved safety goggles, NIOSH-approved dust mask/
respirator, and heavy-duty work gloves during use and service.
2. Stay alert and use common sense when operating. Do not use when tired or
under the inuence of drugs, alcohol or medication.
3. Do not overreach. Keep proper footing and balance at all times. This enables
better control in unexpected situations.
4. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
PRODUCT USE AND CARE
1. This product is not a toy. Keep it out of reach of children.
2. Use the correct product for your application. The correct product will do the job
better and safer at the rate for which it was designed. Do not modify this product
or use it for a purpose for which it is not intended.
3. Check for misalignment or binding of moving parts, breakage of parts and any
other condition that may affect the product’s operation. If damaged, have the
product repaired before use.
4. Use the product and accessories etc., in accordance with these instructions and
in the manner intended for the particular type of product, taking into account
the working conditions and the work to be performed. Use of the product for
operations different from those intended could result in a hazardous situation.
Page 3SKU 96573 For technical questions, please call 1-800-444-3353.
Page 4
VIBRATION HAZARD
This tool vibrates during use. Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury, particularly to the hands, arms
and shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an extended period should rst
be examined by a doctor and then have regular medical check-ups to ensure
medical problems are not being caused or worsened from use. Pregnant women
or people who have impaired blood circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or Raynaud’s Disease should not use this
tool. If you feel any medical or physical symptoms related to vibration (such as
tingling, numbness, and white or blue ngers), seek medical advice as soon as
possible.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands and
ngers, increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the vibration effects on the user.
4. Use tools with the lowest vibration when there is a choice between different
processes.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool
do the work.
7. To reduce vibration, maintain the tool as explained in this manual. If any
abnormal vibration occurs, stop use immediately.
SERVICE
1. Have product serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the product is maintained.
2. Maintain labels and nameplates on the product. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
MISCELLANEOUS
1. Use compressed air only. Only use clean, dry and regulated compressed air at
no more than 90 PSI to power this tool. Never use oxygen, carbon dioxide or
any other bottled gas as a power source for this tool.
Page 4SKU 96573 For technical questions, please call 1-800-444-3353.
Page 5
2. WARNING: The brass components of this product contain lead, a chemical
known to the State of California to cause birth defects (or other reproductive
harm). (California Health & Safety code § 25249.5, et seq.)
3. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contains chemicals known [to the State of California]
to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that
are specially designed to lter out microscopic particles. (California Health &
Safety Code § 25249.5, et seq.)
4. The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Page 5SKU 96573 For technical questions, please call 1-800-444-3353.
Page 6
SPECIFICATIONS
Operating PSI 90 PSI
Air Inlet Size 1/4-18 NPT
Air Consumption 4 CFM
Speed 0 to 10,000 RPM
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
1. Use proper size and type air pressure line and ttings. The recommended air
line for this tool is at least 3/8” delivering no more than 90 PSI. Air inlet size is
1/4” 18 NPT.
2. The use of quick connectors, and an in-line oiler, regulator, and lter are
recommended for use with this product. As shown below:
Oiler
Air
Compressor
Regulator
Tool
Connector
Coupler
Connector Filter
Quick
Air Hose
on Reel
Recommended Air Line Components
3.
Connect a pressurized air source to the Air Valve and set the regulator to 90 PSI.
4. Apply an adhesive-backed sanding head (not included) to the Pad. Cut the
sanding head to size if necessary.
5. Secure all workpieces with a clamp or vise so that both of hands are free to
operate the Sander.
6. Connect the Sander to the air compressor hose at the Regulator Assembly (30).
7. Grip the Handle with your left hand and the Body (13) with your right (reverse if
you are left-handed). Depress the Trigger (28) with your left hand to turn the tool
on.
Page 6SKU 96573 For technical questions, please call 1-800-444-3353.
Page 7
8. Allow the motor to reach its full speed before starting to sand.
9. Turn the Regulator Knob (31) to adjust the oscillation speed. The closer the
Regulator Knob is to “MAX” the faster the Pad will move.
10. Always keep a safe distance from the sanding pad while the Sander is operating.
Do not apply pressure. If the Pad slows down as the material is being worked;
pressure is being applied. Allow the Sander to do the job.
11. Always keep your body and clothing a safe distance from the running Sander.
12. Always maintain a good grip with both hands when operating this tool.
13. After the Sander has been turned off, continue to hold onto the tool with both
hands until the Pad stops completely; then set the tool down.
14. Disconnect Sander from compressor when nished.
15. Clean, then store the product indoors out of children’s reach.
MAINTENANCE AND SERVICING
CAUTION
Damaged products can fail, causing personal injury. Do
not use a damaged product. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, maintenance, and lubrication
1. BEFORE EACH USE, inspect the general condition of the product. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts
and any other condition that may affect its safe operation.
2. AFTER USE, clean external surfaces of the product with clean, moist cloth.
Page 7SKU 96573 For technical questions, please call 1-800-444-3353.
Page 8
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part Description
1 Body Cap
2 Bearing
3 R-Bearing Case
4 Cylinder
5 Spring Pin 2.5x6
6 Rotor
7 Vane
8 Rotor Spacer
9 F-Bearing Case
10 Bearing
11 Lock Nut
12 O-ring 32.5
13 Body
14 Balancer
15 Bolt
16 Pad Retainer
17 Bearing
Part Description
18 Snap Ring
19 Spacer
20 Pad
21 Bolt Set
22 Nut Set
23 Valve Cap
24 O-ring
25 Valve Spring
26 Valve
27 Valve Pin
28 Trigger
29 Spring Pin
30 Regulator Assembly
31 Regulator Knob
32 Nut Set
33 Support
Page 8SKU 96573 For technical questions, please call 1-800-444-3353.
Page 9
ASSEMBLY DIAGRAM
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
Page 9SKU 96573 For technical questions, please call 1-800-444-3353.
Page 10
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free
from defects in materials and workmanship for the period of 90 days from the date of
purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in
no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY
IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection veries the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specic legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Page 10SKU 96573 For technical questions, please call 1-800-444-3353.
Loading...