Central Pneumatic 96314 Assembly And Operation Instructions Manual
SPOT WELD DRILL
Model
96314
®
ASSEMBLY AND OPERATION INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
SPECIFICATIONS
Features
Overall Dimensions 12-1/8” L X 1-3/4” W X 5-1/16” H
Handle Dimensions 5-5/32” L X 1-3/4” OD
Grip Handle Dimensions 8” L X 11/16” W X 1-1/4” H X 5/64” Thick (Spring Loaded)
Activation Method Paddle Switch/Throttle Lever
Air Inlet 1/4” - 18 NPT
Maximum Operating Pressure 90 PSI
Air Consumption 10 SCFM
Maximum Speed 1400 RPM
Minimum Hose Requirement 3/8” ID Hose
Drill Bit Included 1 - High Speed Steel (HSS)/1-5/8” L X 8mm Diameter
Net Weight 4 lb.
3” Hook
Adjustable Depth Stop
Save This Manual
You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Write the product’s serial number in the back of the manual near the assembly
diagram, or write month and year of purchase if product has no serial number. Keep this
manual and invoice in a safe and dry place for future reference.
1.
2.
GENERAL SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
Do not operate this Spot Weld Drill in explosive atmospheres, such as in the pres-
ence of flammable liquids, gases, or metallic dust. This Drill may create sparks
which may ignite fumes.
For technical questions, please call 1-800-444-3353.
Page 2SKU 96314
3.
Keep bystanders, children, and visitors away while operating. Distractions can cause
you to lose control. Protect others in the work area from debris such as metal frag-
ments, and sparks. Provide barriers or shields as needed.
PERSONAL SAFETY
1.
2.
3.
4.
5.
Stay alert. Watch what you are doing, and use common sense when operating. Do
not use this Spot Weld Tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating may result in damage to your
project and/or serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
Avoid accidental starting. Be sure the Throttle Lever (5) is in off position (full up)
before attaching air supply. Carrying power tools with your hand on the Throttle
Lever (5), or attaching an air supply with the Throttle Lever (5) depressed invites
accidents.
Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the Spot Weld Drill in unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, nonskid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
Always wear ANSI-approved safety goggles and a dust mask/respirator under full
face shield when using or performing maintenance on this Spot Weld Drill.
1.
2.
3.
4.
TOOL USE AND CARE
Use clamps (not included) or other practical ways to secure and support the work-
piece to a stable platform. Holding the work by hand or against your body is unstable
and may lead to loss of control.
Do not force the action of the Spot Weld Drill and always use the correct tool for your
application. The correct tool will do the job better and safer at the rate for which it
is designed. Do not force any tool and do not use any tool for a purpose for which
it is not intended.
Do not use the power Spot Weld Drill if the Throttle Lever (5) is in full up position and
the Drill does not off, or if it will not turn on, or off. Any tool that cannot be controlled
with its Power Switch is dangerous and must be replaced.
Disconnect the Spot Weld Drill from its air supply source before making any adjust-
ments, changing accessories, or storing. Such preventive safety measures reduce
the risk of starting the tool accidentally.
For technical questions, please call 1-800-444-3353.
Page 3SKU 96314
5.
Store the idle Spot Weld Drill out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users. Never allow children to come
in contact with this product.
6.
7.
8.
1.
2.
Maintain the Spot Weld Drill with care. Keep bits sharp and clean. Properly main-
tained tools are less likely to bind and are easier to control. Do not use a damaged
tool. Tag damaged tools “Do not use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the Drill’s operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used
on another tool.
SERVICE
Service on this Spot Weld Drill must be performed only by qualified repair person-
nel. Service or maintenance performed by unqualified personnel could result in a
risk of injury.
When servicing, use only identical replacement parts. Follow instructions in the
“Inspection, Maintenance, and Cleaning” section of this manual. Use of unauthor-
ized parts or failure to follow maintenance instructions may create a risk of damage
to the Spot Weld Drill, and/or personal injury.
1.
2.
3.
4.
5.
6.
7.
8.
9.
SPECIFIC SAFETY RULES
Inspect the Drill Bit before use. Never use if the bit is damaged or dull.
Secure the Drill Bit before each use.
Only use a Drill Bit intended for use with this Spot Weld Drill.
Use both hands to securely hold this Spot Weld Drill during use.
Do not exceed the maximum air pressure of 90 PSI.
Compressed air only. Do not use oxygen or any other bottled or flammable gas as
a power source.
Do not modify Drill.
Disconnect the air supply when this Spot Weld Drill is not being used.
Maintain labels and nameplates on the tool. These carry important information. If
unreadable or missing, contact Harbor Freight Tools for a replacement.
For technical questions, please call 1-800-444-3353.
Page 4SKU 96314
Loading...