Central Pneumatic 95030 Set Up And Operating Instructions Manual
3” PNEUMATIC
Model
95030
POLISHER KIT
SET UP AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised 11h
PRODUCT SPECIFICATIONS
Operating Air Pressure 90 PSI
Air Consumption 3.1 CFM @ 90 PSI
Free Speed 2,000 RPM
Air Inlet Size 1/4”- 18 NPT
Recommended Air Hose Diameter 3/8” @ 90 PSI
Disc Attachment Type Hook & Loop
Required Air Inlet Screen 20-Mesh (Included)
Additional Features Rear Air Exhaust
Accessories Open End Wrench (Qty. 1)
Foam Pad (Qty. 2)
Bufng Pad (Qty. 1)
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the inside
of the front cover. Keep this manual and invoice in a safe and dry place for future reference.
UNPACKING
When unpacking, check to make sure that all the parts and accessories listed on
page 9 are included, and the product is intact and undamaged. If any parts are miss-
ing or broken, please call Harbor Freight Tools at the number shown on the cover of this
manual as soon as possible.
SAFETY WARNINGS AND PRECAUTIONS
WARNING! Use eye and hearing protection. 1. Always wear ANSI-approved
safety impact glasses and full face shield when using this Polisher Kit. Also,
wear ANSI approved hearing protection. Other people in the work area must
also wear appropriate ANSI approved safety equipment.
Keep work area clean. 2. Cluttered areas invite accidents.
Stay within air pressure capacity. 3. Never operate the Polisher Kit above 90
PSI.
Observe work area conditions. 4. Keep work area well lit. Do not use pneumatic
tools in the presence of ammable gases or liquids.
Keep children away. 5. Children must never be allowed in the work area. Do not
let them handle machines, tools, extension cords, or air hoses.
Store idle equipment. 6. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 2
Use the right tool for the job. 7. Do not attempt to force a small tool or attach-
ment to do the work of a larger industrial tool. There are certain applications for
which this tool was designed. It will do the job better and more safely at the rate
for which it was intended. Do not modify this tool, and do not use this tool for a
purpose for which it was not intended. Only use the included Foam and Bufng
pads with this Polisher. Never use sanding or grinding accessories.
Dress properly. 8. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid foot-
wear are recommended when working. Wear restrictive hair covering to contain
long hair.
Do not overreach. 9. Keep proper footing and balance at all times. Do not reach
over or across running tools or air hoses.
Disconnect air hose and release any built-up air pressure. 10. Never service
the Polisher Kit or disassemble with the air hose attached. Always release any
built-up air even after disconnecting hose. Disconnect the Polisher Kit when not
in use.
Avoid unintentional starting. 11. Be sure the Trigger (8) is in the OFF position
when not in use and before plugging in. Do not carry any tool with your nger on
the Trigger, whether it is attached to an air source or not.
Stay alert. 12. Watch what you are doing. Use common sense. Do not operate any
tool when you are tired or distracted.
Periodically check your work to make sure that the workpiece is not being 13.
damaged.
Check for damaged parts. 14. Before using any tool, any part that appears dam-
aged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment and binding of moving parts,
any broken parts, and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualied tech-
nician. Do not use the tool if the Trigger does not operate properly.
Replacement parts and accessories. 15. This product is to be repaired and ser-
viced only by a qualied technician. When this product is serviced, only identical
replacement parts should be used. Use of any other parts will void the warranty.
Only use accessories intended for use with this tool. Approved accessories are
available from Harbor Freight Tools.
Do not operate tool if under the inuence of alcohol or drugs. 16. Read warning
labels if taking prescription medicine to determine if your judgement or reexes
are impaired while taking drugs. If there is any doubt, do not operate the tool.
SKU 95030 For technical questions, please call 1-800-444-3353. PAGE 3
Loading...