Central Pneumatic 93742 Assembly And Operating Instructions Manual

6” Random Orbit6” Random Orbit

6” Random Orbit6” Random Orbit

6” Random Orbit

Palm SanderPalm Sander

Palm SanderPalm Sander

Palm Sander

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camar illo, CA 93011

Visit our Web site at http://www .harborfreight.com

Copyright © 2005 by Harbor Freight Tools®. All rights reser ved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

93742

Due to continuing improvements, actual product ma y differ slightly from the product described herein.

SKU 93742 For technical questions, please call 1-800-444-3353. Page 2

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, par ts list and diagram. Keep
your invoice with this manual. W rite the invoice number on the inside of the front
cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injurie s.

2. Observe work area conditions. Do not use machines or power tools such as
air compressor in damp or wet locations. Don’t expose to rain. Keep work
area well lit. Do not use electrically powered tools in the presence of flammable
gases or liquids.

3. Keep children awa y. Children must ne ver be allowed in the w ork area. Do not
let them handle machines, tools, or air lines.

4. Store idle equipment. When not in use, tools must be stored in a dry location
to inhibit rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. There are cer tain applications for
which this tool was designed. It will do the job better
and more safely at the rate for which it was intended. Do not modify this
tool and do not use this tool for a purpose for which it was not intended.

6. Dress properly while working. Do not wear loose clothing or jew elry as they
can be caught in moving par t s . Protective, electr ically nonconductive clothes

noitcurtsnoC

,ydoBmunimulAtsaC

dna,gnisuoHretuOCVP

telnIriAssarB

daPgnikcaB

"8/7-5x"8/3

csiDenahteruyloP

sno

isnemiDtelnIriAelameFTPN81-"4/1deepS

MPR000,01

noitomlatibromodnar

riAegarevA

noitpmusnoC

ISP09@MFC7erusserPr

iA.xaMISP09

snoisnemiDllarevOH"½-4xW"½-4xL"¾-5thgieWteN.sbL2

SKU 93742 For technical questions, please call 1-800-444-3353. Page 3

and nonskid footwear are recommended when wo rking. Wear restrictive hair
cove ring to contain long hair.

7. Use eye and ear protection. Always wear ANSI approved impact safety
goggles. Wear a full face shield if you are producing metal filings or wood
chips. Wear an ANSI approved dust mask or respirator when working around
metal, wood, and chemical dusts and mists.

8. Do not overreach. Keep proper footing and balance at all times. Do not reach
over or across running machines.

9. Maintain tools with care. Keep tools clean and in good condition for better
and safer performance. Follow instructions for lubricating and changing
accessories. Inspect tool fittings and hoses periodically and, if damaged, ha ve
them repaired by an authorized technician. The tool must be kept clean, dry,
and free from oil and grease at all times.

10. Disconnect Air Hose before maintenance. Never service the Sander, clear
jams, or disassemble with the air hose attached. Disconnect the Sander when
not in use.

11. Remove adjusting keys and wrenches. Check that keys and adjusting
wrenches are removed from the tool or machine work surface before connecting
it.

12. Avoid unintentional star ting. Be sure the val ve lever is in the Off position
when not in use and before attaching to pressure source.

13. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.

14. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment and binding of moving
parts; any broken parts or mounting fixtures; and any other condition that may
affect proper operation. Any part that is damaged should be properly repaired
or replaced by a qualified technician. Do not use the tool if the trigger does not
operate properly.

15. Replacement parts and accessories. When ser vicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Appro ved accessories are a vailable
from Harbor Freight Tools.

16. Compressed air only. Never use combustible gas as a power source.

17. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.