Central Pneumatic 93048 Assembly And Operating Instructions Manual

Air Pin Stripe Removal Kit
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
93048
SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 2
Specifications
Construction:
Cast Aluminum with
Steel Parts
Eraser Pads:
(4) 3-1/2” Dia. x 5/8”
Thick Soft Rubber
Pads
Air Inlet: 1/4” - 18 NPT Operating Pressure: 90 PSI
Average Air
Consumption:
4.5 CFM No Load RPM: 3100 RPM
Regulator: Internal Air Regulator Spindle Threads: 5/16” x 24
Dimensions: 8-1/2”L x 2” Diameter Net Weight: 3.08 LBS.
IMPORTANT:
This tool may cause damage to materials or paints that soften when exposed to the heat generated during use (such as acrylic lacquers). For this reason, we strongly recommend that it not be used on these types of materials.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be fol­lowed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don’t expose to rain. Keep work area well lit. Do not use electrically powered tools in the presence of flammable gases or liquids.
3. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, tools, or extension cords.
4. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or
REV 05i
SKU 93048 For technical questions and replacement parts, please call 1-800-444-3353 Page 3
attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for which it was not intended.
6. Dress properly while working. Protect your skin from accidental abrasion burns by wearing long sleeves and safety gloves. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety goggles, full face shield, and ear protection when using this tool. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines.
9. Maintain tools with care. Keep tools clean and in good condition for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool fittings and hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times.
10. Disconnect power. Disconnect from air pressure source when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the work surface before connecting it.
12. Avoid unintentional starting. Be sure the throttle lever is in the Off position when not in use and before attaching to pressure source. Do not carry any tool with your hand on the throttle lever, whether it is attached or not. Disconnect the air hose from the tool when not in use.
13. Stay alert. Do not operate any tool when you are tired.
14. Check for damaged parts. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if the throttle lever does not function properly.
15. Guard against electric shock when working on electrical equipment, such as your air compressor. Prevent body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerator enclosures.
Loading...
+ 6 hidden pages