Central Pneumatic 92849 Assembly And Operating Instructions Manual
1/4” Air Ratchet Wrench1/4” Air Ratchet Wrench
1/4” Air Ratchet Wrench1/4” Air Ratchet Wrench
1/4” Air Ratchet Wrench
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2005 by Harbor Freight Tools®. All rights reser ved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor F reight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
92849
SKU 92849 Page 2
Specifications
Save This Manual
You will need the manual for the saf ety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. K eep
your inv oice with this man ual. Write the inv oice number on the inside of the front
cover. Keep the manual and inv oice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area c lean . Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or po wer tools in
damp or wet locations. Don’t expose to rain. Keep work area well lit. Do not
use electrically powered tools in the presence of flammable gases or liquids.
3. Keep children a way. Children must ne v er be allow ed in the w ork area. Do
not let them handle machines, tools, or extension cords .
4. Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Alw a ys loc k up tools and k eep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain
applications for which this tool was designed. It will do the job better
and more safely at the rate for which it was intended. Do not modify this
tool and do not use this tool for a purpose for which it was not intended.
:noitcurtsnoC
htiwydoBmunimulatsaC
tehctaRleetSdenihcaM
deepSgnitarepO
:euqroTdna
isp09tampr052
euqrotdellortnoCrotalugeR
:noitpmusnoCriAMFCS5.31:euqroT).W.C.C(sbl/tf13).W.C(sbl/tf33
:eziStelnIriATPN81-"4/1:evirDerauqS"4/1
:snoisnemiDllarevO.aiD"2/1-1xH"4/1-2xL"2/1-8:thgieWteN.sbL6.1
:erusserPgnikroW.xaMisp09:noitceriDgnitarepOelbisreveR
SKU 92849 Page 3
6. Dress properly while working. Do not wear loose clothing or jewelry as
they can be caught in moving parts. Protective, electrically non-conductive
clothes and non-skid footwear are recommended when working. Wear
restrictive hair cov ering to contain long hair.
7. Use eye and ear protection. Always wear ANSI approved impact safety
goggles. W ear a full f ace shield if y ou are producing metal filings or w ood
chips. Wear an ANSI approved dust mask or respirator when working around
metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not
reach over or across running machines.
9. Maintain tools with care. Keep tools clean and in good condition for better
and safer performance. Follow instructions for lubricating and changing
accessories. Inspect tool fittings and hoses periodically and, if damaged, have
them repaired by an authorized technician. The handles must be kept clean,
dry , and free from oil and grease at all times.
10. Disconnect power. Disconnect from air pressure source when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting
wrenches are removed from the tool or machine work surface before
connecting it.
12. Avoid unintentional starting. Be sure the switch is in the Off position when
not in use and before attaching to pressure source. Do not carry any tool with
your finger on the trigger, whether it is attached or not.
13. Stay alert. Watch what you are doing, use common sense. Do not operate
any tool when you are tired.
14. Check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check f or alignment and binding
of moving parts; any broken parts or mounting fixtures; and an y other
condition that may aff ect proper operation. Any part that is damaged should
be properly repaired or replaced by a qualified technician. Do not use the tool
if any switch does not turn On and Off properly.
15. Guard against electric shock when working on electrical equipment.
Prevent body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerator enclosures.
Loading...