Central Pneumatic 92208 Assembly And Operation Instructions Manual

AIR IMPACT WRENCH

®

AND

RATCHET SET

Model 92208

ASSEMBLY AND OPERATION

INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

REV 11h

TO PREVENT SERIOUS INJURY,

Specifications

Air Inlet
Maximum Operating Pressure 90 PSI (All tools)

Air Ratchet

Dimensions 1-5/8” D x 10-3/8” L
Drive Size 3/8” Sq.
Maximum Torque Output 50 Ft. Lbs.
Air Consumption 4 CFM
No Load RPM 150 (Reversible)

Impact Wrench

Dimensions 2-3/4” W x 7-1/4” L x 8” H
Drive Size 1/2” Sq.
Maximum Torque Output 240 Ft. Lbs.
Air Consumption 4 CFM
RPM 6,500 (Reversible)
BPM 1,020

1

/4”-18 NPT (All tools)

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instruc­tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with
this manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tools, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use machines or power tools in damp or
wet locations. Don’t expose to rain. Keep work area well lit. Do not use electrically
powered tools in the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, extension cords, or air hoses.

4. Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. There are certain applications for which this
tool was designed. It will do the job better and more safely at the rate for which it was
intended. Do not modify this tool and do not use this tool for a purpose for which it
was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically nonconductive clothes and nonskid footwear are
recommended when working. Wear restrictive hair covering to contain long hair.

SKU 92208 For technical questions, please call 1-800-444-3353. Page 2

7. Use eye and ear protection. Always wear ANSI approved impact safety goggles.
Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical
dusts and mists.

8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or
across running machines or air hoses.

9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.

10. Disconnect air supply. Disconnect air hose when not in use.

11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches
are removed from the tool or machine work surface before connecting the tool.

12. Avoid unintentional starting. Be sure the trigger is released when not in use and
before connecting to the air source. Do not carry any tool with your finger on the
trigger, whether it is connected or not.

13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.

14. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified technician.
Do not use the tool if the trigger does not operate properly.

15. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.

16. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.

17. Industrial applications must follow OSHA guidelines.

18. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.

19. Use proper size and type extension cord. If an extension cord is required, it must
be of the proper size and type to supply the correct current to the compressor without
heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical
damage to the compressor. Check your air compressor’s manual for the appropriate
size cord.

20. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.

SKU 92208 For technical questions, please call 1-800-444-3353. Page 3