Central Machinery 99782 User Manual
RIGHT ANGLE MITER GAUGE
99782
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SAVE THIS MANUAL
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
General Tool Safety Warnings
WARNING Read all safety warnings and instructions. Failure to follow the
warnings and instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
Work area safety1.
Keep work area clean and well lit. a. Cluttered or dark areas invite accidents.
Keep children and bystanders away while operating a power tool. b. Distrac-
tions can cause you to lose control.
Personal safety2.
Stay alert, watch what you are doing and use common sense when operating a.
a power tool. Do not use a power tool while you are tired or under the inu-
ence of drugs, alcohol or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection.b. Safety
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will reduce personal injuries.
Do not overreach. Keep proper footing and balance at all times.c. This enables
better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, cloth-d.
ing and gloves away from moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
Only use safety equipment that has been approved by an appropriate stan-e.
dards agency. Unapproved safety equipment may not provide adequate protec-
tion. Eye protection must be ANSI-approved and breathing protection must be
NIOSH-approved for the specic hazards in the work area.
SKU 99782 For technical questions, please call 1-800-444-3353. Page 2
Unpacking
When unpacking, make sure that the items shown below are intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number
shown throughout the manual as soon as possible.
PARTS LIST AND ASSEMBLY DIAGRAM
1
2
3
No replacement parts are available.
Part Description Qty.
1 Steel Bar 1
2 Handle 1
3 Miter Body 1
4 Nut 1
5 Miter Slot Bolt 1
6 Handle Threaded Rod 1
7 Pin 1
8 Angle Pointer 1
9 Screw 1
5
4
7 8
6
ASSEMBLY
Place the Steel Bar (1) on a at, hard surface. Thread the Handle Threaded Rod 1.
(6) into the Steel Rod. Thread the Nut (4) onto the Threaded Rod (6). Tighten the
Nut (4) onto the Threaded Rod (6) so that the the Threaded Rod (6) is locked into
place. See Figure A below.
9
NOTE2. : Do not extend the Threaded Bolt (6) beyond the bottom surface of the the
Steel Bar. It must be ush with the bottom of the Steel Bar (1).
Thread the Miter Slot Bolt (5) into the Steel Bar (6). Attach the Angle Pointer (8) 3.
onto the Miter Slot Bolt (5), secure it using the Screw (9). See Figure A below.
Figure A
SKU 99782 For technical questions, please call 1-800-444-3353. Page 3
Pivot Pin Hole
(4)
(6)
(9)
(8)
(5)
Loading...