Central Machinery 95346 Assembly And Operation Instructions Manual
GASOLINE AUGER DRILL
Model
95346
Distributed exclusively by
Harbor Freight Tools
®
.
1.5 HP
ASSEMBLY AND OPERATION INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
CAUTION!
Your Warranty Is Voided If:
You do not operate the Auger Drill with the proper 25:1 unleaded fuel/2-cycle oil mix in its fuel tank. Do not
run the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper fuel mix,
low or no fuel mix, will permanently damage the unit.
You do not operate the Auger Drill with the proper amount of SAE 80-90 gear oil in its Gearbox. Do not run the
Auger Drill with low or no gear oil. Running the Auger Drill with low or no gear oil will permanently damage
the unit.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
ALL WARNINGS AND INSTRUCTIONS BEFORE USE.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 07b, 07e
SPECIFICATIONS
Engine Specications 1.5 HP / 52cc / Single Cylinder / 2-Stroke / Recoil Start
Fuel Required 25:1 Unleaded Gasoline (89 octane or better) & 2 Cycle Oil Mixture
Fuel Tank Capacity 0.26 Gallon
Recommended Gear Oil SAE 80 – 90 Weight Gear Oil
Rotation Single Rotation Only (Clockwise)
Drilling Speed 150 RPM
Maximum Drilling Depth 1’ 10”
Auger Diameter 4”
Overall Bit Length 2’ 6-3/4” Long
Cutting Edge Length 2’ Long
Drive Shaft 7/8” Diameter x 1-1/2” Long
Accessories Auger Bit / Fuel & Oil Mixing Container / Spark Plug Wrench
Flat Head Screwdriver / Hex Keys (Qty. 2) / Storage Bag
Weight 17-1/4 lb. (without fuel and oil)
This product requires a 25:1 ratio of unleaded fuel and 2-cycle oil to be added to
its fuel tank before starting. Attempting to start the Engine with an improper fuel mix, low
or no fuel mix WILL ruin the Engine and void the warranty.
This product requires the proper amount of SAE 80-90 gear oil in its Gear Case
before starting. Attempting to start the Auger Drill with low or no gear oil WILL ruin the
Gear Case and void the warranty.
The Engine’s Carburetor may need to be adjusted by a qualied mechanic for efcient high-altitude use.
The Emission Control System for this product’s engine is warranted for standards
set by the U.S. Environmental Protection Agency. For warranty information, refer to the
last pages of this manual.
SAVE THIS MANUAL
You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the front
cover. Keep this manual and invoice in a safe and dry place for future reference.
SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 2
REV 07b, 07e
GENERAL SAFETY RULES AND PRECAUTIONS
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in
electric shock, re, and/or serious injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. 1. Cluttered benches and dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the pres-2.
ence of ammable liquids, gases, or dust. Power tools create sparks which may
ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool. 3.
Distractions can cause you to lose control. Provide barriers or shields as needed.
Children should not be allowed in the work area.
PERSONAL SAFETY
Stay alert. Watch what you are doing, and use common sense when operat-1.
ing a power tool. Do not use a power tool while tired or under the inuence
of drugs, alcohol, or medication. A moment of inattention while operating power
tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. 2.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Make sure to remove the Spark Plug before per-3.
forming any service, maintenance, or cleaning procedures on the unit.
Remove adjusting keys or wrenches before turning the Auger Drill on. 4. A
wrench or a key that is left attached to a rotating part of the machine may result in
personal injury.
Do not overreach. Keep proper footing and balance at all times. 5. Proper footing
and balance enables better control of the power tool in unexpected situations.
TOOL USE AND CARE
Do not force the tool. Use the correct tool for your application. 1. The correct
tool will do the job better and safer at the rate for which it is designed.
SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 3
Do not use the Auger Drill if the Kill Switch does not turn it off. 2. Any tool that
cannot be controlled with its Kill Switch is dangerous and must be replaced.
Store idle tools out of reach of children and other untrained persons. 3. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. 4. Properly maintained tools are less likely to malfunction
and are easier to control. Do not use a damaged tool. Tag damaged tools “Do
not use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts, and any 5.
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your 6.
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
Tool service must be performed only by qualied repair personnel. 1. Service or
maintenance performed by unqualied personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instruc-2.
tions in the “Inspection, Maintenance, And Cleaning” section of this manual.
Use of unauthorized parts or failure to follow maintenance instructions may create
a risk of electric shock or injury.
SPECIFIC SAFETY RULES AND PRECAUTIONS
IMPORTANT! 1. Your Warranty is voided if:
You do not operate the Auger Drill with the proper 25:1 fuel mix in its fuel a.
tank. Do not run the Engine with an improper fuel mix, low or no fuel mix. Run-
ning the Engine with an improper fuel mix, low or no fuel mix, will permanently
damage the unit.
You do not operate the Auger Drill with the proper amount of SAE 80-90 b.
gear oil in its Gearbox. Do not run the Auger Drill with low or no gear oil. Run-
ning the Auger Drill with low or no gear oil will permanently damage the unit.
Maintain labels and nameplates on the Auger Drill. 2. These carry important infor-
mation. If unreadable or missing, contact Harbor Freight Tools for a replacement.
3. Always wear safety equipment. When operating the Auger Drill,
wear ANSI-approved safety impact eye goggles, hearing protection,
heavy duty work gloves, sturdy steel-toed work boots, and head
protection.
SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 4
Do not leave the Auger Drill unattended when it is running. 4. Turn off the Engine
before leaving.
Do not allow children and other unauthorized people to handle or play with 5.
the Auger Drill. Do not leave the drill unattended in an area accessible to
children.
Maintain a rm grip on the Auger Drill with both hands and be aware of the 6.
strong start-up torque of the tool.
Keep your thumb near the Kill Switch in the event the Auger Drill must be 7.
turned off immediately.
Do not use the Auger Drill if the Auger is dull, bent, or damaged.8.
Avoid accidental damage to underground pipes, electric lines, cables, etc. 9.
and possible personal injury. Contact your local public utility companies (gas,
water, electric, cable, etc.) prior to drilling in an unknown area.
Drill with the Engine running at full speed. 10. Fully squeeze the Speed Control
Lever and maintain a steady drilling speed.
Keep the Auger clean and sharp.11.
Keep all guards and safety devices in proper working order and properly 12.
adjusted.
Before starting the Engine, make sure the Auger is not contacting any ob-13.
ject.
When shutting off the Engine, and make sure the Auger has stopped before 14.
setting the tool down.
CARBON MONOXIDE PRECAUTIONS
This Auger Drill is designed for outdoor use only. Do not operate the Auger
Drill in a closed area or in a poorly ventilated area. When running, the Engine
of this product produces carbon monoxide, a colorless, odorless, toxic gas
that, when inhaled, can cause serious personal injury or death.
FIRE AND EXPLOSION PRECAUTIONS
1. Gasoline fuel and fumes are ammable, and potentially explosive. Use
proper fuel storage and handling procedures. Have multiple ABC class re
extinguishers nearby.
Keep the Auger Drill and surrounding areas clean at all times.2.
SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 5
When spills of fuel or oil occur, they must be cleaned up immediately. 3. Dis-
pose of uids and cleaning materials as per any local, state, or federal codes and
regulations. Store oil rags in a covered metal container.
Do not store fuel or other ammable materials near the Auger Drill.4.
Do not smoke, or allow sparks, ames, or other sources of ignition around 5.
the Auger Drill.
Keep grounded conductive objects, such as tools, away from exposed, live 6.
electrical parts and connections to avoid sparking or arcing. These events
could ignite fumes or vapors.
Do not rell the Fuel Tank while the Engine is running or while the Engine is 7.
still hot. Do not operate the Auger Drill with known leaks in the fuel system.
Use only Engine manufacturer recommended fuel and oil.8.
MECHANICAL PRECAUTIONS
Prior to performing service, maintenance, or cleaning procedures, allow the 1.
Engine to completely cool. Then, remove the spark plug from the Engine.
Do not alter or adjust any part of the Auger Drill or Engine that is assembled 2.
and supplied by the manufacturer.
Follow scheduled Auger Drill and Engine maintenance.3.
CHEMICAL PRECAUTIONS
Avoid contact with hot fuel, oil, exhaust fumes, and solid surfaces.1.
Avoid body contact with fuels, oils, and lubricants used in the Auger Drill and 2.
Engine. If swallowed, seek medical treatment immediately. Do not induce vomiting
if fuel is swallowed. For skin contact, immediately wash with soap and water. For
eye contact, immediately ush eyes with clean water.
WARNING: This product contains or, when used, produces a chemical 3.
known to the State of California to cause cancer and birth defects or other
reproductive harm. (California Health & Safety Code § 25249.5, et seq.)
NOTE: This item does not meet California CARB requirements and is not
for sale or use in California.
NOISE PRECAUTIONS
Prolonged exposure to high noise levels is hazardous to hearing. Wear
proper hearing protection when operating or working around the Auger Drill when
it is running.
SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 6
REV 09b
Loading...