Central Machinery 94099 Assembly Instructions Manual

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

Copyright © 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

ASSEMBLY INSTRUCTIONS

MACHINE STAND

94099

Due to continuing improvements, actual product may differ slightly from the product described herein.

SKU 94099 For technical questions, please call 1-800-444-3353. Page 2

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the
front cover. Keep the manual and invoice in a safe and dry place for future
reference.

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Keep work area well lit while assembling.

3. Check for damaged parts. Before using any product, any part that

appears damaged should be carefully checked to determine that it will
perform its intended function. Check for any broken or damaged parts and
any other conditions that may affect its operation. Replace or repair
damaged or worn parts immediately.

4. Always check hardware and assembled parts after assembling. All

connections should be tight and hardware tightened.

5. Keep children away. Children must never be allowed in the work area

when assembling or using this product.

6. Dress Properly. Non skid footwear is recommended when setting up this

product. Wear restrictive hair covering to contain long hair.

7. Use eye protection. Always wear ANSI approved impact safety goggles

when setting up this product.

Finish
Overall Dimensions
Table Top Dimensions
Weight Capacity
Table To p Fr a me
Table Top Frame Dims.
Pull Out Shelf Dims.
Weight Capacity of Shelf

Lacquered Finish-MFD/11/16” Thick Material
12-5/8”L x 31-3/4”W x 34-3/4”H
13-7/8”L x 31-5/8”W x 11/16” Thick
500 Lbs.
Hot Rolled Steel Plate-Finish, Black
11-13/16”L x 24-1/8”W x 2-3/4”H
12”L x 14-3/8”W x 11/16” Thick
30 Lbs.

SKU 94099 For technical questions, please call 1-800-444-3353. Page 3

8. Maintain product with care. Follow instructions for setting up this product.

Inspect periodically.

9. Do not overreach. Keep proper balance at all times when setting up this

product. Never sit or stand on the Machine Stand.

10. Use the right product for the job. There are certain applications for which

this product was designed. Do not modify this product or use this product for
a purpose other than which it was intended.

11. Do not assemble this product if under the influence of alcohol or
drugs. Read warning labels on prescriptions to determine if your judgement
or reflexes are impaired while taking drugs. If there is any doubt, do not set­up this product.

12. Be sure this product is located on a smooth level surface capable of

supporting the weight of objects placed on the stand, and all related
tools placed on the shelf. Maintain balance of machinery on the
Machine Stand. If too much weight is placed on the pullout Shelf, the Stand

will topple. Do not exceed the maximum weight capacities shown on page 2.

13. For safe assembly of this product, an individual may require assitance from
another person while assemblying portions of the Machine Stand.

Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
operator.

Unpacking

When unpacking this product check to make sure that all parts are included
as shown in the parts list. If any parts are missing or broken, please call

Harbor Freight Tools at the number below.

SKU 94099 For technical questions, please call 1-800-444-3353. Page 4

Step 1:

1. Turn the Table Frame (B) over on a smooth surface. Attach the Pull-Out
Bracket (K) to the Table Frame (B) as shown in

Figure 1.

Figure 1

Pull Out Shelf

Pull Out Shelf

ASSEMBLY INSTRUCTIONS

SKU 94099 For technical questions, please call 1-800-444-3353. Page 5

Step 2:

1. Attach the Table Frame (B) to the Table Top (A). Use Bolts (E) in the
predrilled holes.

Figure 2.

Turn this assembly over.

Figure 2

SKU 94099 For technical questions, please call 1-800-444-3353. Page 6

Step 3:

1. Place the four Feet (I) with Nuts (H) to the Front Legs (C1) and Back Legs
(C2). Tighten the Nuts.

See Figure 3.

Figure 3

Step 3a:

SKU 94099 For technical questions, please call 1-800-444-3353. Page 7

Step 4:

1. Attach Front Legs (C1) and Back Legs (C2) to Leg Support Frame (D) with
Bolts (J), Washers (F), Rings (G), and Nuts (H).

See Figure 4.

Figure 4

SKU 94099 For technical questions, please call 1-800-444-3353. Page 8

Step 5:

1. Place the Table Top Assembly (A & B) on top of the Legs (C1 and C2),
matching the holes in the Table Frame (B). Note: Legs fit inside Table Top.

See Figure 5.

Figure 5

SKU 94099 For technical questions, please call 1-800-444-3353. Page 9

Step 6:

1. Secure the Table Top Assembly (A & B) on top of the Legs (C1 and C2),
matching the holes in the Table Frame (B) with Bolts (J), Washers (F), Rings
(G), and Nuts (H).

See Figure 6.

Figure 6

1. Wipe the Table Top (A) and Pull-Out Shelf with a clean, damp cloth. Dry well.

2. When not in use, store in a dry place to avoid rust and corrosion.

3. Periodically check the Machine Stand to make sure all parts and hardware
are tightly secured in place.

Maintenance/Inspection

Assembly is complete. Make sure all hardware is tight before using the Machine
Stand.

SKU 94099 For technical questions, please call 1-800-444-3353. Page 10

PARTS LIST

(See part’s descriptions on page 11.)

SKU 94099 For technical questions, please call 1-800-444-3353. Page 11

NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.

Parts List

Parts Identification

Part # Description Qty.

Table To p
Table Frame w/ Pull-Out Shelf
Front Legs
Back Legs
Leg Support Frame
Bolt
Flat Washer

A
B
C1
C2
D
E
F

1
1
2
2
1
6
16

Lock Washer
Nut
Feet
Bolt
Pull-Out Bracket
Screw

G
H
I
J
K
L

16
20
4
16
1
2

Part # Description Qty.

Part A

Part B

& J

Part C1

Part D

Part K & L

Part C2

Part H & I

Part J, F,

G ,& H

Pull-Out Shelf

SKU 94099 For technical questions, please call 1-800-444-3353. Page 12

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS

THERETO.

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of
maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]

LIMITED 90 DAY WARRANTY