Page 1
ROTROT
ROTROT
ROT
ARAR
ARAR
AR
Y TY T
Y TY T
Y T
ABLE - 3 INCHABLE - 3 INCH
ABLE - 3 INCHABLE - 3 INCH
ABLE - 3 INCH
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
Copyright © 2004 by Harbor Freight Tools®. All rights reser ved. No por tion of this
manual or any artwork contained herein may be reproduced in any shape or for m
without the express written consent of Harbor F reight T ools .
For technical questions and replacement parts, please call 1-800-444-3353
92066
Page 2
SKU 92066 For technical questions, please call 1-800-444-3353 Page 2
Specifications
Item Description
Application For use on sm all milling and multipurpose
machines.
Table Diame ter 3 inches
Table Rotation 360 degrees in 10 de gree increme nts (with
marks eve ry 5 degree s)
Hand W hee l Scale 10o per revolution marked at 30 m inute
increments
Machine Mounting T-slots for vertical and horizontal mounting
Mounting Slot Dim ens ions 1/4 (W) x 0.47 (D) inch es
Overall Dimensions 4-7/8 (L) x 5-3/8 (W) x 1-1/2 (H) inches
Table Dimens ions 3 (dia.) x 1/2 (H) inches
Weight 3.2 lbs.
Save This Manual
You will need the manual for the saf ety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram. K eep
your inv oice with this man ual. Write the inv oice number on the inside of the front
cover. Keep the manual and inv oice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool!
1. Keep work area c lean . Cluttered areas invite injuries.
2. Observe work area conditions. Do not use machines or po wer tools in
damp or wet locations. Don’t expose to rain. K eep work area well lighted.
Do not use electrically powered tools in the presence of flammab le gases or
liquids.
3. Keep children awa y. Children must nev er be allo wed in the w ork area. Do
not let them handle machines, tools, or extension cords .
4. Store idle equipment. When not in use, tools must be stored in a dry
location to inhibit rust. Alw a ys loc k up tools and k eep out of reach of children.
5. Use the right tool for the job. Do not attempt to force a small tool or
attachment to do the work of a larger industrial tool. There are certain
applications for which this tool was designed. It will do the job better and
more safely at the rate for which it was intended. Do not modify this tool and
do not use this tool for a purpose for which it was not intended.
Page 3
SKU 92066 For technical questions, please call 1-800-444-3353 Page 3
6. Dress properly. Do not wear loose clothing or je welry as they can be caught
in moving parts. Protectiv e , electrically non-conductiv e clothes and non-skid
footwear are recommended when w orking. Wear restrictive hair co v ering to
contain long hair .
7. Use eye and ear protection. Always wear ANSI approved impact saf ety
goggles. W ear a full f ace shield if y ou are producing metal filings or w ood
chips. W ear an ANSI appro v ed dust mask or respirator when working around
metal, wood, and chemical dusts and mists.
8. Do not overreach. Keep proper footing and balance at all times. Do not
reach over or across running machines.
9. Maintain tools with care. Keep tools sharp and clean for better and safer
performance. F ollow instructions f or lubricating and changing accessories.
Inspect tool cords periodically and, if damaged, have them repaired by an
authorized technician. The handles must be kept clean, dry, and free from oil
and grease at all times.
10. Remove adjusting keys and wrenches. Check that k e ys and adjusting
wrenches are removed from the tool or machine w ork surface before
operating.
11. Stay alert. Watch what y ou are doing, use common sense. Do not operate
any tool when you are tired.
12. Check for damaged parts. Bef ore using an y tool, an y part that appears
damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check f or alignment and binding
of moving parts; any broken parts or mounting fixtures; and an y other
condition that may aff ect proper operation. Any part that is damaged should
be properly repaired or replaced by a qualified technician.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are
availab le from Harbor F reight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read
warning labels if taking prescription medicine to determine if your judgment or
reflex es are impaired while taking drugs. If there is any doubt, do not operate
the tool.
15. Maintenance. F or your safety, service and maintenance should be
performed regularly by a qualified technician.
Page 4
SKU 92066 For technical questions, please call 1-800-444-3353 Page 4
Rotary T ab le Specific Saf ety Precautions
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that ma y occur. It
must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator .
Warning: The brass components of this product contain lead, a chemical known
to the State of California to cause birth defects (or other reproductive harm).
(California Health & Safety Code 25249.5 et seq.)
Caution: Prior to using the Rotary Table on a milling or other machine, make
sure to read and understand all instructions and safety precautions as outlined in the machine’s operation manual.
Unpacking
When unpacking, check to mak e sure that all the parts are included. Ref er to the
Parts List and Assembly Dra wing at the end of this man ual. If any parts are
missing or broken, please call Harbor F reight Tools at the number on the cover of
this manual.
Operation
1. Secure the Rotary Table to the saddle of the milling machine using the two
vertical or horizontal mounting slots on the Rotary Table and appropriate
hardware (not supplied).
2. Securely mount the workpiece to the Rotary Table (hardware not supplied).
3. Loosen Brass Screw (2), then turn Hand Wheel (5) to move the table to the
desired angle. Read the angle (in deg rees and seconds) on the Rotary Table
(7) and Hand Wheel (5) scales .
4. Retighten Brass Screw (2).
5. Begin milling operation as outlined in the operating manual of the machine
being used. Adhere to all warnings and instructions provided in the manual.
Maintenance
1. To clean the Rotary Table, apply a mild solv ent to a clean cloth and wipe
clean.
2. To prevent o xidation, apply a thin coat of light oil to the surface and all moving
parts.
3. Store the Rotary Table in a clean and dry location.
Page 5
SKU 92066 For technical questions, please call 1-800-444-3353 Page 5
Parts List
Item Description Qty
1. Base 1
2. Brass Screw 1
3. Guide Rod for Handle 1
4. Vernier Wheel 1
5. Hand Wheel 1
6. Screw 4
7. Rotary Table 1
8. Handle Rod 1
9. Base Plate and Pin 1
10. Bearing 1
Assembly Drawing
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN
THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR
DISTRIBUTOR MAKES ANY REPRESENTA TION OR WARRANTY OF ANY KIND TO THE B UYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE
OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND
PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
NOTE: Some par ts are listed and shown for illustration purposes only
and are not available individually as replacement parts.
Loading...