Center 340006 User Manual

Operating Your Controller

Normal Operation

For normal operation the slider must be in the Run
Programme position.

A red indicator lamp shows when the heating or hot
water is switched ON.

Two Mode buttons are provided to select how the
heating and hot water are controlled.

Heating

Keep pressing the
through the 4 possible modes:

Off - The heating will remain OFF.

Auto - The heating will be switched ON and OFF

automatically according to the heating programme.

Once - The heating will come ON at the first

programmed ON time and go OFF at the last
programmed OFF time.

Cont. - The heating will remain ON continuously.

The Hot Water

Mode

manner as described above for the Heating Mode
button.

Boost

The BOOST buttons switch the heating or hot water
ON for up to 3 hours without altering the programme.

Pressing either button once will give one hour boost,
and the words HEATING +1 HR or HOT WATER +1 HR
show on the display to confirm the button has been
pressed.

When the red indicator lamp is OFF, pressing the
BOOST button switches the heating or hot water ON
for just one hour.

When the red indicator lamp is ON, pressing the
BOOST button extends the programmed ON period
by one hour.

Further presses of the BOOST buttons will increase
the boost period by one hour for each button press,
up to a maximum of 3 hours. The display will change
to show the number of hours of boost, for example
HEATING +3 HR or HOT WATER +2 HR.

To cancel the boost hours, keep pressing the BOOST
button until the HEATING + (1, 2 or 3) HR or HOT

WATER + (1,2 or 3) HR disappears from the display.

For further information telephone [phone]

Whilst every care has been taken to ensure that the information included in
this document was accurate at the time of printing, we reserve the right to
change specifications at any time.
The photographs reproduced in this publication are within the constraints of
the printing process and are NOT to be used for matching purposes. E&OE.
Wolseley UK, The Wolseley Center, Harrison Way, Spa Park,
Royal Leamington Spa, CV31 3HH

Mode button to scroll

button operates in the same

Advance

The ADVANCE buttons switch the heating or hot
water ON or OFF without altering the programme.

When the indicator lamp is ON, pressing the ADVANCE
button switches the heating or hot water OFF until the
next programmed ON time.

When the indicator lamp is OFF, pressing the

ADVANCE button switches the heating or hot water
ON until the next programmed OFF time.

Power Failure

Your programmer stores the programme in non-volatile
memory to ensure correct operation after a mains
supply power cut. Date/time/mode are saved regularly
so you may only need to correct the time after a power
cut of more than a few minutes. Follow the instructions
for “Setting the Correct Date/Time” overpage.

WEEE Directive 2012/19/EU

At the end of the product life dispose
of the packaging and product in a
corresponding recycling centre. Do
not dispose of the unit with the usual
domestic refuse. Do not burn the product.

User Guide

for 340006 (EHE0200363) Programmer

42009084-015 AB

Introduction

The programmer controls your central heating system.
It will enable you to select the times when heating and
hot water are switched ON and OFF.

Features

• Weekday/weekend heating programme.

•

• Three ON/OFF switching times per day.

•

• ADVANCE buttons for heating and hot water.

• BOOST buttons for heating and hot water, giving

Weekday/weekend hot water programme.

Built-in programme with typical ON/OFF times.

up to 3 hours of boost.

• Settings stored in non-volatile memory to prevent

loss of programme during power cuts.

• 12 hour am/pm or 24 hour clock format.

The programmer and other controls in your
central heating system will provide comfortable
temperatures in your home when you want them.

12 hour am/pm or 24 hour clock display

Your programmer can operate on 12 hour am/pm or
24 hour clock formats. To change the format, ensure
the slider is in the Run Programme position then press

-

the + and

buttons together for about 3 seconds. All
the displayed times will be automatically changed to
the new format.

Repeating this procedure will change the clock display
back to the original format.

Weekday/Weekend Programming

When setting the programme times (slider is in Set
Heating or Set Hot Water positions) the applicable

days will be displayed as a block of days (Mon...Fri or
Sat...Sun). The Day button will switch between the
Weekday and Weekend programmes when pressed.

Ref: 4277

Setting Your Programmer

Setting the Correct Date/Time

To set the correct date and time, unclip the fascia on
the front of the programmer.

STEP 1

Move the slider to the
Set Date/Time position.
The day of the month
will now be flashing
to indicate it can be
changed.

STEP 2

To change the day, press the + or
correct day is displayed. Then press the Confirm/Next
button to confirm and move to the next setting.

STEP 3

Set the month, year and time in the same way, pressing

Confirm/Next to move on each time.

STEP 4

Move the slider to Run Programme to complete
setting the date and time.

–

buttons until the

Choice 1 Press the Day button to switch to

programming Saturday and Sunday. The ON/OFF
times for Saturday and Sunday can then be set as
described in steps 6 to 8.

or
Choice 2 Press the Copy button to copy the Monday

to Friday programme into Saturday and Sunday.

*NOTE*

1. When pressing the + button, the next ON or OFF
marker may start to flash. If this happens the next
programme time will have been changed. Press
the Confirm/Next button to check and adjust this
programme time if necessary.

2. When pressing the - button, the previous ON or OFF
marker may start to flash. If this happens the previous
programme time will have been changed. Follow the
procedure in “Reviewing Programme Times” to
check and adjust this time if necessary.

Moving the slider to the next position completes
setting the hot water programme.

HOT WATER

BOOST

BUTTON

HOT WATER

INDICATOR

LAMP

HOT WATER

ADVANCE

BUTTON

DAY SELECT

BUTTON

COPY

PROGRAMME

BUTTON

HOT WATER

MODE INDICATOR

TIME

DISPLAY

DATE

DISPLAY

PROGRAMME

TIME MARKERS

HEATING MODE

INDICATOR

HEATING
BOOST
BUTTON

HEATING
INDICATOR
LAMP

HEATING
ADVANCE
BUTTON

SLIDER

Setting the Hot Water Programme

The hot water programme has three ON/OFF switching
times per day. Each time can be set between 3.00 am and

2.50 am (on the next day) to allow you to programme
the hot water to stay on past midnight, if required.

STEP 5

Move the slider to the Set Hot Water position. The
words HOT WATER will now be visible on the display
and the days for Monday to Friday and the first ON
time will now be flashing.

STEP 6

Use the + and – buttons to set the first ON time. Each
press of the button will change the time by 10 minutes.

STEP 7

Press the Confirm/Next button once to confirm any
changes and display the first OFF time. Set this time
using the + and – buttons.

STEP 8

By pressing the

Confirm/Next

and + or – buttons the

two remaining ON/OFF times can be set. If you only
require two ON/OFF times per day it is recommended
you set the second OFF time equal to the second ON
time. Be sure to press

Confirm/Next

after making any

changes.

STEP 9

This completes setting the hot water programme for
Monday to Friday.

You now have a choice to set the programme for

Saturday and Sunday:-

Setting the Heating Programme

The heating programme has three ON/OFF switching
times for every day. Each time can be set between

3.00 am and 2.50 am (on the next day) to allow you

to programme the heating to stay on after midnight
if required.

STEP 10
Move the slider to the Set Heating position. The word
HEATING will now be visible on the display, and the

days Monday to Friday and the first ON time will now
be flashing.

STEP 11

The required heating programme for Monday to Friday
and Saturday/Sunday can now be set by following
the same procedure as “Setting the Hot Water

Programme” in steps 6 to 9.

STEP 12

Moving the slider to the next position completes
setting the heating programme.

Reviewing Programme Times

To review your hot water programme move the slider
to the Set Hot Water position.

To review your heating programme move the slider to
the Set Heating position.

To review the programme times for a day press the

Confirm/Next button repeatedly. Any of these times

–

can be adjusted by using the + and

buttons.

Press the Day button to review weekday or weekend
programmes.

Built-in Programme

Monday

to Friday

Saturday

and Sunday

HEATING

HOT WATER

HEATING

HOT WATER

3.00am

Personal Programme

Monday

to Friday

Saturday

and Sunday

HEATING

HOT WATER

HEATING

HOT WATER

3.00am

HOT WATER

MODE BUTTON

4.00am

5.00am

6.00am

7.00am

4.00am

5.00am

6.00am

7.00am

8.00am

8.00am

– AND +

BUTTONS

9.00am

10.00am

9.00am

10.00am

CONFIRM/NEXT

1.00pm

11.00am

12.00am

1.00pm

11.00am

12.00am

BUTTON

2.00pm

3.00pm

2.00pm

3.00pm

HEATING MODE

BUTTON

4.00pm

5.00pm

6.00pm

4.00pm

5.00pm

6.00pm

7.00pm

7.00pm

8.00pm

8.00pm

9.00pm

9.00pm

10.00pm

10.00pm

11.00pm

11.00pm

12.00pm

12.00pm

1.00am

1.00am

2.00am

2.00am

3.00am

3.00am