Page 1
18 RANGE ANALOG MUL18 RANGE ANALOG MUL
18 RANGE ANALOG MUL18 RANGE ANALOG MUL
18 RANGE ANALOG MUL
TITESTERTITESTER
TITESTERTITESTER
TITESTER
OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www .harborfreight.com
Copyright© 2005 by Harbor F reight Tools®. All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor F reight Tools .
For technical questions and replacement parts, please call 1-800-444-3353
®
32418
WARNING!
Electric shock can cause DEA TH or SEVERE PERSONAL INJURY.
Never touch exposed conductors of electricity with
fingers, hands or any other body part.
Page 2
SKU 32418 Page 2For technical questions, please call 1-800-444-3353.
Specifications
Save This Manual
Y ou will need the man ual for the safety warnings and precautions, and operating
and maintenance procedures. K eep your in voice with this manual. Write the inv oice
number on the inside of the front cover . Keep the manual and in voice in a safe and dry
place for future reference.
noitcnuFycaruccA/egnaR
segnaRegatloVCA*DSF%5±V0001/005/052/05/01
segnaRegatloVCDDSF%5±V0001/005/052/05/01/52.0
segnaRegarepmACD )Vm004<:porDegatloV(DSF%5±Am005/52/5.2/52.0
segnaRecnatsiseR
K/01x/1x
Ω
crafo%5±
serutaeFrehtO
oreZ,tseTrotsisnarT,tseTytiunitnoC,tseTyrettaBV5.1
oreZdna,tsujdA Ω tsujdA
noitcelfeDelacS-lluF="DSF"*
METINOITPIRCSED
noitcetorPdaolrevOedoiddnaesufA5.0
ycneuqerFzH06
yalpsiDtnemevomlacinahcemortcele,golanA
yrettaBseirettaB"AA"owT
erutarepmeTgnitarepOF°401ot°23
ytidimuHgnitarepOHR%58nahtsseL
erutarepmeTegarotSF°221ot°41
thgieWsbl7.0
seirosseccA(deR + (kcalBdna) - sdaeLtseT"53)
Page 3
SKU 32418 Page 3For technical questions, please call 1-800-444-3353.
Safety Warnings and Precautions
WARNING: When using tool, basic saf ety precautions should alwa ys be f ollow ed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tester!
If all warnings and safety precautions in this manual are not followed
completely , the protection pr ovided b y this product will be reduced.
On this sheet, and in the included manual:
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious personal injury.
CAUTION indicates a potentially hazardous situation which, if not a v oided,
may result in a minor/moderate personal injury or damage to this tool or the unit
being tested by it.
WARNING
1. A void w orking alone. If an accident happens, an assistant can bring help.
2. Keep work area clean. Cluttered areas invite injuries.
3. Av oid electrical shock. Use extreme caution when working around uninsulated
conductors or bus bars. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and cabinet enclosures when testing voltages.
4. Av oid damaging meter. Use only as specified in this manual.
5. Observe work area conditions. Do not test circuits in damp or wet locations.
Don’t expose to rain. K eep work area well lit.
6. Keep children awa y. Children m ust never be allo wed in the work area. Do not
let them handle machines, tools, or extensions cords.
7. Store idle equipment. When not in use, tools must be stored in a dry location
to inhibit rust. Always lock up tools and keep out of reach of children.
8. Dress properly. Do not wear je welry as an accidental brush may cause a short
circuit causing electric shock or severe burns. Protective, electrically nonconductive clothes and nonskid rubber-soled footwear are recommended when
working. W ear restrictive hair covering to contain long hair .
9. Use eye protection. Always wear ANSI approved impact safety goggles.
10. Do not overreach. K eep proper f ooting and balance at all times. Do not reach
over or across electrical cables or frames.
11. Maintain tools with care. Ensure m ultimeter has a fresh battery. Inspect tool
cords periodically and, if damaged, have them repaired by an authorized technician.
12. Stay alert. W atch what you are doing, use common sense. Do not operate an y
tool when you are tired.
Page 4
SKU 32418 Page 4For technical questions, please call 1-800-444-3353.
13. Check for damaged parts. Bef ore using any tool, any part that appears dam-
aged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment and binding of mo ving parts;
any broken parts or mounting fixtures; and an y other condition that may affect
proper operation. In addition to a general inspection, look specifically for:
a. Pay special attention to the insulation protecting the connectors.
b. Check the leads for e xposed metal, damaged insulation, and continuity .
Replace damaged test leads immediately , bef ore use.
Any part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any s witch does not oper ate properly.
14. Remove the test leads before performing maintenance, opening the case,
or the battery compartment.
15. Do not use the multimeter if:
a. The test leads are damaged in any way.
b. The battery is low.
c. Near any explosive gasses or fumes.
d. Any abnormal operation is detected.
(If in doubt about the condition of the meter, ha v e it serviced.)
e. The battery cover is open.
16. This meter should be powered only b y tw o, correctly installed 1.5V “AA”
type batteries.
17. Accessories. Only use accessories intended for use with this tool. Approved
accessories are availab le from Harbor Freight Tools.
18. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
19. People with pacemakers should consult their physician(s) before using
this product. Electromagnetic fields in close proximity to a heart pacemaker
could cause interference to or f ailure of the pacemaker .
In addition, caution is necessary when near the coil, spark plug cables, or
distributor of a running engine. The engine should always be off if adjust-
ments are to be made to the distributor .
20. Do not test voltage on circuits higher than 1,000 volts. Do not test current
on DC circuits higher than .5 amps or on A C circuits at all.
Warning: The w arnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but m ust be supplied b y the operator .
Page 5
SKU 32418 Page 5For technical questions, please call 1-800-444-3353.
Unpacking
When unpacking, make sure that the Analog Multimeter and both Test Leads
are included. If an y parts are missing or broken, please call Harbor F reight Tools at
the number on the cover of this manual.
CAUTION
1. Prior to testing capacitors, resistance, diodes, or continuity; disconnect all power
to the circuit and discharge all high-voltage capacitors.
2. Check fuse before testing current.
3. Use the proper settings, terminals, techniques, and range for the tests per-
formed. Alw ays start with the range stated in the instructions.
4. Be careful not to apply voltage to the Test Leads when the meter is in an ohms
testing position. Damage can occur to the multimeter .
NOTE:
The batteries must be
installed before first use.
See
Battery Replacement
under
Maintenance
, page 11.
Page 6
SKU 32418 Page 6For technical questions, please call 1-800-444-3353.
Control and Scale Layout
Refer to this diagram while following the directions in the
Operation
section.
The bold numbers inside brackets [XX] below refer to the page number where the
explanation of the function starts.
-COM Jack + Jack
Transistor
Selection
Area [9]
DC Current
Selection
Area (mA)
[8]
Ohm
Selection
Area (Ω) [8]
AC Volt
Selection
Area [8]
Ohm Zero
Adjust [8]
DC V olt
Selection
Area [7]
Continuity
Selection
Area [9]
Battery
Selection
Area [10]
Ohm Scale
[8]
Current
Gain Scale
(hFE) [9]
Battery
Test Scale
[10]
Accuracy
Mirror [6]
Leakage
Current
(lceo) Scale
[9]
Amperage/
Voltage
Scales [7]
Continuity
Indicator [9]
The Accuracy Mirror
The Accuracy Mirror is used to insure that the meter’ s pointer is being read
straight, ensuring accuracy . Simply make sure that the meter is angled so that, when
reading it, the reflection of the pointer is hidden under the pointer.
Zero Adjust
[10]
Page 7
SKU 32418 Page 7For technical questions, please call 1-800-444-3353.
WARNING!
Electric shock can cause DEA TH or SEVERE PERSONAL INJURY.
Always observe the following precautions when working:
1. Never touch exposed conductors of electricity with fingers, hands or any
other body part.
2. Use caution when working near voltages above 30 VAC rms, 42 V AC peak,
or 60 VDC. Voltages this high present a risk of electric shock.
3. Disconnect the circuit’ s power before connecting the meter in series, when
measuring current.
4. Connect the common (COM) test lead first and disconnect it last.
5. Hold the probes with fingers behind guards.
Operation
DC V olta ge Measurements
Measure DC voltages up to 1,000 V.
1. T urn the Range Selector Switch to 1000 DCV.
Always start with the highest range
if the voltage is unknown.
2. Plug the red lead into the + Jack.
Plug the black lead into the -Com
Jack.
3. Carefully touch the appropriate exposed conductors with the tips of the
probes to measure the voltage (not
amperes).
4. Read measurement on the V olt/Amp
Scale - see
How to Read the Volt/
Amp Scale
table, right.
If the needle moves in the opposite
direction, then the probes are connected incorrectly. Reverse the
probes’ locations.
If the voltage is less than 500 volts,
set the Range Selector Switch to the
next lower range until the meter
pointer is mid-range on the scale.
elacSpmA/tloVehtdaeRotwoH
egnaRpmA/tloV
elacSpmA/tloV
daeRebot
reilpitluMtluseR
000101-0001
00505-001
052052-0–
0505-0–
52052-01.0
01
(rof CD ylno)
01-0–
01
(rof CA ylno)
deR elacS01-0
–
5.2052-010.0
52.0052-0100.0
:trahCehtesUoT
(tfelehtniegnardetcelesehtdniF.1 egnaR .nmuloc)
(retnecehtnidetacidnielacsehtdaeR.2 elacS )
.wortahtfonmuloc
thgirehtnireilpitlumehtybgnidaerehtylpitluM.3
( reilpitluM "afI.wortahtfonmuloc)–ninwohssi"
eriuqertonseodgnidaerehtneht,nmulocthgireht
.noitacilpitlum
:elpmaxE ottessiegnarehtfI AmCD52 ehtneht, 052-0 elacs
ybdeipitlumdnadaerebdluow 10.0 .
( tnemerusaeM=reilpitluMXgnidaeR )
fognidaerarof,oS 011 dluowtnemerusaemeht,egnarsihtni
eb AmCD1.1 ( 1.1=10.0X011 .)
Page 8
SKU 32418 Page 8For technical questions, please call 1-800-444-3353.
5. When testing is complete, remov e Test Leads and store them and the meter in a
safe, dry location.
AC V oltage Measurements
Measure AC v oltages up to 1,000 V.
1. Turn the Range Selector Switch to 1000 ACV.
Always start with the highest range if the voltage is unknown.
2. Follow the directions on the previous page under
DC Voltage Measurements
(except for the polarity directions, they are unnecessary with AC).
DC Current Measurements
Measure DC conductors carrying up to 500 mA (.5 A).
1. Turn the Range Selector Switch to the 500 DCmA position. Plug the red lead
into the + Jack. Plug the black lead into the -Com Jack.
Note: Testing current should ONLY be done in series, with the circuit con-
nected and current flowing.
3. Carefully connect the test leads to the circuit or the load being tested.
4. If the Amperage is less than 25 mA (.025 A), set the Range Selector Switch to
the next lower range until the meter pointer is mid-range on the scale.
5. When testing is complete, remov e Test Leads and store them and the meter in a
safe, dry location.
Resistance (Ohm) Measurements
Circuit resistance can be measured on ranges from meter reading times 1 to meter
reading times 1,000.
Note: Testing resistance should ONLY be done with the power to the circuit
disconnected. Test to make sure no voltage is present first. If voltage is
applied while testing, disconnect the tester immediately , otherwise the fuse
may blow and the tester may be damaged-see
Fuse Replacement
under
Maintenance,
page 11.
1. Turn the Range Selector Switch to the Ohm testing position (between x1
ΩΩ
ΩΩ
Ω and
K
ΩΩ
ΩΩ
Ω) you will be measuring at.
2. Plug the red lead into the + Jack. Plug the black lead into the -Com Jack.
3. Short the Test Leads together . The meter should read “0” Ohms.
4. If the meter does not read “0” Ohms, the ohmmeter needs to be calibrated to
enable accurate measurements.
a. With the test leads held together , adjust the Ohm Zero Adjust Knob until the
meter’s pointer aligns on “0”.
b . If the pointer can’t align with zero , the batteries may need to be replaced-see
Battery Replacement
under
Maintenance
, page 10.
Page 9
SKU 32418 Page 9For technical questions, please call 1-800-444-3353.
5. Touch the exposed conductors with the tips of the Test Leads. If , b y chance, a
voltage is present, the fuse may blow-see
Fuse Replacement
under
Mainte-
nance,
page 11. Immediately remo ve the Test Leads from the conductors.
6. Read the Ohm Scale. If in the x1
ΩΩ
ΩΩ
Ω setting, the measurement is as read. If in
the x10
ΩΩ
ΩΩ
Ω setting, multiply the reading by 10. If in the xK
ΩΩ
ΩΩ
Ω setting, multiply the
reading by 1,000.
If the resistance measured is off the scale, move the Range Selector Switch to
a higher Ohms position.
7. Continuity T esting: Turn the Range Selector Switch to the Continuity (x1
Ω)Ω)
Ω)Ω)
Ω)
setting. This test is a type of Ohms test. When the wir ing between the test
leads has low resistance, the Continuity Indicator will illuminate . This is useful
for detecting breaks in wiring.
8. When testing is complete, switch the meter to a DCV testing location (to
help prolong battery life), remove the Test Leads, and store the leads and
meter in a safe, dry location.
Transistor Measurements
Caution: This tester is capab le of damaging or destro ying a transistor. It is entirely
the responsibility of the user to ensure that the settings are correct for the
specific transistor before connecting the meter. Harbor Freight Tools takes no
responsibility for any damage, whether direct or consequential that may be
done to the device under test due to improper use or connection.
1. Turn the Range Selector Switch to the hFE (x10
Ω)Ω)
Ω)Ω)
Ω) position and set the “0”
Ohms as stated above.
2. T o check the Iceo (leak) v alue:
a. Plug the red lead into the + Jack. Plug the black lead into the -Com Jack.
b . Carefully connect the black test lead to the emitter and the red test lead to
the collector of the transistor being tested.
c. Read the Iceo value on the Iceo scale.
3. T o chec k the hFE value:
a. If connecting to a PNP transistor:
Plug the black lead into the -Com Jack and connect the other end of the
lead to the Emitter. Connect the hFE Connector (an optional accessory ,
see page 12) to the + Jack. Carefully connect its red clip to the Collec-
tor and its black clip to the Base.
If connecting to a NPN transistor:
Plug the red lead into the + Jack and connect the other end of the lead
to the Emitter. Connect the hFE Connector (an optional accessory , see
page 12) to the -Com Jack. Carefully connect its red clip to the Collec-
tor and its black clip to the Base.
b . The meter will show the approximate hFE (IC/IB) value on the hFE scale.
Page 10
SKU 32418 Page 10For technical questions, please call 1-800-444-3353.
Maintenance
1. Wipe unit with a damp cloth using a light detergent. Do not use solvents or
abrasives. Allow the unit to dry completely before use or storage.
2. Remove batteries if not in use for long periods.
4. Store unit in a dry location out of children’s reach.
5. Aside from the fuse and batteries, there are no user replaceable parts on this
unit. REP AIRS SHOULD BE DONE ONLY BY A QU ALIFIED TECHNICIAN.
6. Meter Pointer Calibration
Over time, it may become necessary to adjust the meter pointer to align on “0.”
a. Remove the Test Leads from the multimeter and make sure that the unit is
not set at an Ohm testing setting.
b . Using a small standard screwdriver , place it on the small meter Zero Adjust
screw right below the center of the dial. See
Control and Scale Layout
on
page 6.
c. T urn screw slightly until the pointer points directly at the zero on the Amper-
age/V oltage Scale.
Figure A
Screw
4. When testing is complete, switch the meter to a DCV testing location (to
help prolong battery life), remove the Test Leads, and store the leads and
meter in a safe, dry location.
Battery Testing
1. Turn the Range Selector Switch to the 1.5V (“AAA”, “AA”, “C”, & ”D” Size Battery) setting.
2. Plug the red lead into the + Jack. Plug the black lead into the -Com Jack.
3. Connect the red test lead to the positive end of the battery and the black lead to
the negative.
4. Read measurement. When testing is complete, remove Test Leads and store
them and the meter in a safe, dry location.
7. Battery Replacement
If the Ohms cannot be adjusted to
indicate zero , the batteries require
replacement.
a. Remove the Test Leads from the
multimeter.
b . T urn the unit over to show its back.
c. Remove the screw indicated in
Figure A
using a cross-head
screwdriver.
Page 11
SKU 32418 Page 11For technical questions, please call 1-800-444-3353.
d. Open the back cover .
e. Remove the batteries and replace
them, being sure to align the new
batteries properly . See
Figure B
.
f. Put the back cover on, bottom
edge first. See
Figure C
. Then,
retighten the screw .
Figure C
Figure B
Fuse
spare
fuse
holder
“AA” Batteries
8. Fuse Replacement
If the multimeter is exposed to excessive current, misused, or dropped, the fuse may
become blown. Check the fuse if the meter does not work for no apparent reason.
a. Follow directions a through d un-
der
Battery Replacement
to
remove the back cove r.
b . Note the location of the spare fuse
holder and the fuse in
Figure B
.
Note: A spare fuse is not in-
cluded.
c. Carefully examine the fuse in the
meter. If the thin wire in the tube
is broken, the fuse is blown and
needs to be replaced. See
Fig-
ure D
.
Warning: ONLY replace the fuse
in this meter with another fast-
acting 0.5A fuse. Using the
wrong fuse or using another
material or object instead of a
fuse is very dangerous and
may cause a fire.
d. After replacing the fuse, close the
meter . Put the bac k cover on, bot-
tom edge first. See
Figure C
.
Then, retighten the screw .
Figure D
Fuse
Page 12
SKU 32418 Page 12For technical questions, please call 1-800-444-3353.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUF ACTURER AND/OR DISTRIBU TOR HAS PRO VIDED THE
WIRING DIAGRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER
THE MANUF ACTURER OR DISTRIBUT OR MAKES ANY REPRESENT A TION OR
W ARRANTY OF ANY KIND TO THE BUYER THA T HE OR SHE IS QU ALIFIED T O
MAKE ANY REP AIRS T O THE PRODUCT, OR THA T HE OR SHE IS Q UALIFIED
TO REPLA CE ANY P ARTS OF THE PR ODUCT . IN F A CT , THE MANUF ACTURER
AND/OR DISTRIBUT OR EXPRESSL Y ST A TES THA T ALL REPAIRS AND P ARTS
REPLACEMENTS SHOULD BE UNDER T AKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NO T BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INST ALLA TION OF REPLA CEMENT P ARTS THERET O.
Wiring Diagram
Aside from the fuse and batteries, there are no
user replaceable parts on this unit.
Note: The hFE connector is available as an optional accessory.
It can be ordered using part Sku 28532.
Loading...