Page 1
2005 NEW PRODUCT PROPOSAL
CPX 2350
Description: 2 channel alarm with dual polarity door locks, trunk/hatch release, dual stage shock
sensor, starter disable output, 20 watt single tone siren, mini-transmitters.
B.O.M.:
1- Main Unit
2- mini -transmitters at 433.9 MHz.
1- 20 watt six tone siren (SN3541 20 watt single tone- Same as Auto Page standard)
1- dual zone shock sensor
1- valet/override switch
1- LED with white plug
1- 3 -pin plug for dual polarity door lock/unlock outputs (same as Auto Page standard)
1- Mul ti-pin alarm wire harness
1- 5 -pin standard power harness
1- 2 -color box (Auto Page to provide the design)
1- Manuals for Operations and Installation (English and Spanish)
Specifications:
1. 500 milli-amp output for starter disable (ground while armed)
2. 500 milli-amp output for door lock/unlock outputs
3. 200 milli-amp output for 2nd channel trunk release
4. Dual polarity parking light with 2 fuses (one for main power / one parking light
power input) on the 5-pin power harness.)
5. On board parking light relay (same as Auto Page standard)
Programming:
PROGRAMMING:
Note: This system can keep up to 4 remote transmitters in its memory. If more than 4 transmitters
programmed, the system will keep only the last 4 transmitters.
PROGRAMMING THE REMOTE TRANSMITTER
Enter:
1. Turn the Ignition ‘switch ‘OFF/ON’ 3 TIMES and stay in ON
position. Within 15 seconds.
2. Push the Valet switch 2 times. (Holding in on the 2nd push) until you hear a long chirp. The
transmitter is ready to program.
Program:
1. Press any button on the transmitter until the siren responds with a confirming chirp the first
transmitter is now programmed.
2. Press button on the second transmitter until the siren responds with a confirming chirp, the
second transmitter is now programmed.
3. Apply the same procedure to program 3rd and 4th
Exit: Turn Ignition to ‘OFF’ position, or leave it for 15 seconds. A 3 long chirps & 3 parking light
flashes to confirm exit.
.
Page 2
FEATURE PROGRAMMING:
FEATURE “A” PROGRAMMING:
1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 3 times (holding in on the 3rd push) until one chirp with a long chirp is
heard, then release the valet switch. You are now in the Alarm feature ‘A’ programming
mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
(See chart on next page)
The siren chirps and LED pause will indicate new setting.
The factory default settings are always [1] LED flash, [1] siren chirp.
4. Depress the transmitter button to change the feature. Simply keep re-depressing the
transmitter button again until the module advances to your desired setting.
a. In this case, Press the button again, the module would advance
to [2] LED flash, [2] horn chirp.
b. Press the button again; the module would advance to [3] LED
flash, [3] horn chirps etc.
Press
Transmitter
Button
1
2
3
4 +
5 +
Exit: Turn Ignition to ‘ON’ position, or leave it for 15 seconds.
3 long chirps & 3 parking light flashes will confirm exit.
Notice : The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCCRULES. OPERATIONS IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFEERENCE THAT MAY CAUSE UNDESRIED OPERATION
One Chirp /
LED one pulse
Factory Default
Setting
Active arming
Automatic Rearm
off
Instant Door Ajar
error chirp
Siren Confirmation
chirp on only
Ignition Alarm
trigger “ON”
Two Chirps /
LED two pulses
Passive arming
without passive
door locking
Automatic Rearm
on
45 seconds delay
Door Ajar error
chirp.
All Confirmation
chirps off
Ignition Alarm
trigger “OFF”
Three Chirps /
LED three
pulses
Passive arming
with passive
door locking.
Four Chirps /
LED four
pulses
Page 3
One Chirp /
FEATURE “B” PROGRAMMING:
1 Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 5 times (holding in on the 5th push) until two chirps with a long chirp is
heard then release the valet switch. You are now in the Alarm feature ‘B’ programming mode.
3 Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
1
2
3
4 +
LED one pulse
Factory
Default Setting
Pathway
illumination
feature “off”
Ignition
controlled door
locks &
unlocks
0.8-second
Door lock
pulses.
Car Jacking
Off
Two Chirps /
LED two
pulses
Parking light
turns “on” for
30- second
upon an
unlock signal
Ignition
controlled
door locks
only
3.5-second
Door lock
pulse.
Car Jacking
On
Three Chirps /
LED three
pulses
Ignition
controlled door
unlocks only
Double pulse
unlock
Four Chirps /
LED four
pulses
Without
ignition
controlled
door locks &
unlocks
5
+
H1/4 Brown
Wire =
(+) Siren
Output
Exit: Turn Ignition to ‘ON’ position, or leave it for 15 seconds.
3 long chirps & 3 parking light flashes will confirm exit.
Transmitter Operation
Transmitter
Button
System Function Remark
H1/4 Brown
Wire =
(+) Horn pulse
Output (Relay
Required for
negative out)
＊
II
-
+
-
-
Lock Doors & Arm System
Panic function Press and Hold for 3 seconds
Car Locator Under armed mode
Arm and Delete The 2 Stage Shock
Sensor
Silent Arming / Disarming Ignition in "off" position.
Unlock Doors & Disarm System
Two Steps Door Unlock & Disarm
System
Trunk Release (Channel 2) Press and Hold for 2 seconds
Passive Arming By-pass While the system Disarmed.
Silent Arming / Disarming Press within 3 seconds
Control another car Press and Hold for 2 seconds
Press twice within 3 seconds
Press twice within 3 seconds.
Loading...