Celestron 21094 User manual

ENGLISH

O

mnnii XXLLTT SSeerriieess TTeelleessccooppeess

O

m

IINNSSTTRRUUCCTTIIOONN MMAANNUUAALL

●● OOmmnnii XXLLTT 110022 ●● OOmmnnii XXLLTT 110022EEDD ●● OOmmnnii XXL

●● OOmmnnii XXLLTT112277 ●● OOmmnnii XXLLTT 115500 ●● OOmmnnii XXLLTT 115500RR

LTT 112200

TTaabbllee ooff CCoonntteennttss

INTRODUCTION .......................................................................................................................................................... 4

Warning...................................................................................................................................................... 4

ASSEMBLY .................................................................................................................................................................... 8

Setting up the Tripod.................................................................................................................................. 8

Attaching the Equatorial Mount ................................................................................................................. 9

Attaching the Center Leg Brace ............................................................................................................... 10

Installing the Counterweight Bar.............................................................................................................. 10

Installing the Counterweights................................................................................................................... 11

Attaching the Slow Motion Control Knobs (Cables)................................................................................11

Attaching the Telescope Tube to the Mount............................................................................................. 12

Installing the Finderscope......................................................................................................................... 13

Installing the Visual Back......................................................................................................................... 13

Installing the Star Diagonal ...................................................................................................................... 14

Installing the Eyepieces............................................................................................................................ 14

Moving the Telescope Manually .............................................................................................................. 15

Balancing the Mount in R.A..................................................................................................................... 15

Balancing the Mount in DEC ................................................................................................................... 16

Adjusting the Mount................................................................................................................................. 16

Adjusting the Mount in Altitude............................................................................................................... 17

Adjusting the Mount in Azimuth.............................................................................................................. 17

TELESCOPE BASICS ................................................................................................................................................. 18

Image Orientation..................................................................................................................................... 20

Focusing ................................................................................................................................................... 20

Aligning the Finderscope ......................................................................................................................... 21

Calculating Magnification........................................................................................................................ 21

Determining Field of View....................................................................................................................... 22

General Observing Hints .......................................................................................................................... 22

ASTRONOMY BASICS............................................................................................................................................... 23

The Celestial Coordinate System ............................................................................................................. 23

Motion of the Stars ................................................................................................................................... 24

Latitude Scale........................................................................................................................................... 25

Pointing at Polaris .................................................................................................................................... 25

Finding the North Celestial Pole .............................................................................................................. 26

Polar Alignment in the Southern Hemisphere.......................................................................................... 27

Pointing at Sigma Octantis ....................................................................................................................... 28

Finding the South Celestial Pole (SCP).................................................................................................... 28

Declination Drift Method of Polar Alignment.......................................................................................... 29

Aligning the R.A. Setting Circle .............................................................................................................. 30

Using the R.A. Vernier Scale ................................................................................................................... 31

CELESTIAL OBSERVING......................................................................................................................................... 32

Observing the Moon................................................................................................................................. 32

Lunar Observing Hints ............................................................................................................................. 32

Observing the Planets............................................................................................................................... 32

Observing the Sun .................................................................................................................................... 33

Solar Observing Hints .............................................................................................................................. 33

Observing Deep Sky Objects.................................................................................................................... 33

Seeing Conditions..................................................................................................................................... 33

2

Transparency ............................................................................................................................................ 33

Sky Illumination....................................................................................................................................... 33

Seeing ....................................................................................................................................................... 34

Using the Lens Cap Aperture Stop with Refractor Telescopes ................................................................ 34

ASTROPHOTOGRAPHY........................................................................................................................................... 35

Piggyback Photography............................................................................................................................ 35

Short Exposure Prime Focus Photography for Refractors & Newtonians................................................ 36

Short Exposure Prime Focus Photography for Schmidt-Cassegrains....................................................... 36

Eyepiece Projection for a Schmidt-Cassegrain......................................................................................... 37

Long Exposure Prime Focus Photography ............................................................................................... 38

Planetary and Lunar Photography with Special Imagers.......................................................................... 39

CCD Imaging for Deep Sky Objects ........................................................................................................ 40

Terrestrial Photography............................................................................................................................ 40

Metering ................................................................................................................................................... 40

Reducing Vibration .................................................................................................................................. 40

TELESCOPE MAINTENANCE ................................................................................................................................. 41

Care and Cleaning of the Optics............................................................................................................... 41

Collimation of Refractors......................................................................................................................... 41

Collimation of a Schmidt-Cassegrain....................................................................................................... 42

Collimation of a Newtonian ..................................................................................................................... 44

OPTIONAL ACCESSORIES ...................................................................................................................................... 48

APPENDIX A - TECHNICAL SPECIFICATIONS ...................................................................................................51

APPENDIX B - GLOSSARY OF TERMS.................................................................................................................. 52

SKY MAPS.................................................................................................................................................................... 55

CELESTRON TWO YEAR WARRANTY ................................................................................................................ 61

3

Congratulations on your purchase of an Omni XLT Series telescope. The Omni XLT Series of telescopes come in
several different models: 102mm refractor, 102mm ED refractor, 120mm refractor, 150mm refractor, 150mm
Newtonian, 127mm Schmidt-Cassegrain. The Omni Series is made of the highest quality materials to ensure
stability and durability. All this adds up to a telescope that gives you a lifetime of pleasure with a minimal amount
of maintenance. Furthermore, your Celestron telescope is versatile — it will grow as your interest grows. This
instruction manual covers all the different models of the Omni XLT telescopes.

No matter at what level you are starting out, the Omni XLT Series telescopes will unfold for you and your friends
all the wonders of the Universe.

Some of the many standard features of the Omni XLT include:

• Hand selected optical glass and hand figured optics resulting in superior images.

• Premium Celestron Starbright XLT optical coatings that provide maximum contrast and image sharpness.

• Heavy-duty equatorial mount with a rugged and very stable stainless steel tripod.

• Ball bearings in both axes of the mount ensure smooth performance.

• CD-ROM “The Sky” --- astronomy software which provides education about the sky and printable sky maps.

Many other high performance features!

The Omni XLT deluxe features combined with Celestron’s legendary optical systems give amateur astronomers the
most sophisticated and easy to use telescopes available on the market today.

Take time to read through this manual before embarking on your journey through the Universe. It may take a few
observing sessions to become familiar with your telescope, so you should keep this manual handy until you have
fully mastered your telescope’s operation. The manual gives detailed information regarding each step as well as
needed reference material and helpful hints guaranteed to make your observing experience as simple and pleasurable
as possible.

Your telescope is designed to give you years of fun and rewarding observations. However, there are a few things to
consider before using your telescope that will ensure your safety and protect your equipment.

WWaarrnniinngg

 Never look directly at the sun with the naked eye or with a telescope (unless you have the

proper solar filter). Permanent and irreversible eye damage may result.

 Never use your telescope to project an image of the sun onto any surface. Internal heat build-up

can damage the telescope and any accessories attached to it.

 Never use an eyepiece solar filter or a Herschel wedge. Internal heat build-up inside the telescope

can cause these devices to crack or break, allowing unfiltered sunlight to pass through to the eye.
Never leave the telescope unsupervised, either when children are present or adults who may not be
familiar with the correct operating procedures of your telescope.

- 4 -

12

10

11

9

1

2

3

4

5

6

7

8

Figure 1-1 Omni XLT 102 Refractor

(Omni XLT 102ED, Omni XLT 120 and Omni XLT 150R refractors are similar)

1. Optical Tube 7. 1.75" Steel Tripod

2. Tube Rings 8. Accessory Tray/ Leg Brace

3. Finderscope 9. Counterweights

4. Eyepiece 10. Counterweight Bar

5. Equatorial Mount 11. Dovetail Slide Bar

6. Latitude Adjustment Screw 12. Objective Lens Shade

- 5 -

12

11

10

1

2

3

4

5

6

7

8 9

Figure 1-2 Omni XLT 150 Newtonian

1. Finderscope 7. 1.75" Steel Tripod

2. Finderscope Bracket 8. Accessory Tray/ Leg Brace

3. Focuser 9. Counterweights

4. Eyepiece 10. Counterweight Bar

5. Tube Rings 11. Dovetail Slide Bar

6. Equatorial Mount 12. Optical Tube

- 6 -

12

11

10

1

2

3

4

9

5

8

6

7

Figure 1-3 Omni XLT 127 Schmidt-Cassegrain

1. Optical Tube 7. 1.75" Steel Tripod

2. Finderscope 8. Counterweights

3. Finderscope Bracket 9. Counterweight Bar

4. Equatorial Mount 10. Declination Setting Circle

5. Latitude Scale 11. Dovetail Slide Bar

6. Accessory Tray/ Leg Brace 12. Schmidt Corrector Lens

- 7 -

This section covers the assembly instructions for your Celestron Omni XLT telescope. The equatorial mount is
exactly the same for all the Omni telescope models and the optical tubes have some differences which will be noted.
Your Omni telescope should be set up indoor the first time so that it is easy to identify the various parts and
familiarize you with the correct assembly procedure before attempting it outdoor.

Each Omni telescope comes in two boxes. One box contains the tripod, tripod accessory tray/brace, equatorial
mount, counterweight bar, two counterweights, R.A. knob, Dec knob, polar axis polar cap, and a Phillips head
screwdriver. The second box contains the telescope optical tube assembly, finderscope and bracket, eyepiece, and
other standard accessory items per the specific model that you have.

SSeettttiinngg uupp tthhee TTrriippoodd

Remove the tripod from the box that it is in (Figure 2-1). The Omni tripod comes with an all metal center leg
brace/accessory tray to give rock solid support to the mount. The tripod comes fully assembled with a metal plate,
called the tripod head that holds the legs together at the top. In addition, there is a central rod that extends down
from the tripod head that attaches the equatorial mount to the tripod. To set up the tripod:

1. Stand the tripod upright and pull the tripod legs apart until each leg is fully extended. The tripod will now stand

by itself (Figure 2-2). Once the tripod is set up, you can adjust the height at which it stands.

2. Loosen the lever (turn counterclockwise) on the leg clamp so that the tripod leg can be adjusted (Figure 2-3).

3. Slide the center portion of the tripod leg away from the tripod head until it is at the desired height.

4. Tighten the levers (turn clockwise) on each leg clamp to hold the legs in place.

5. The standard height of the tripod is 33” and it can be extended at any height up to a maximum of 47”.

Remember that the tripod will be the most rigid and stable at the lowest height.

Figure 2-1 Figure 2-2 Figure 2-3

- 8 -

AAttttaacchhiinngg tthhee EEqquuaattoorriiaall MMoouunntt

The equatorial mount allows you to tilt the telescope’s axis of rotation so that you can track the stars as they move
across the sky. The Omni mount is a German equatorial mount that
tripod head there is a metal alignment peg for aligning the mount. This side of the tripod will face north when
setting up for an astronomical observing session. To attach the equatorial head:

1. Locate the azimuth adjustment screws on the equatorial mount (see Figure 2-4).

2. Retract the screws so they no longer extend into the azimuth housing on the mount. DO NOT remove the

screws since they are needed later for polar alignment.

3. Hold the equatorial mount over the tripod head so that the azimuth housing is above the metal peg.

4. Place the equatorial mount on the tripod head so that the two are flush. You can rotate the mount slightly to the

center position (where the front latitude adjustment screw is directly over the “N” on the tripod). Then tighten
the azimuth adjustment screws.

5. Tighten the mounting knob (attached to the central rod) on the underside of the tripod head to hold the

equatorial mount firmly in place.

Equatorial
Mount

Azimuth Adjustment
Screws

Figure 2-4

attaches to the tripod head. On one side of the

Tripod
Head

Alignment
Peg

Mounting
Knob

Figure 2-5

- 9 -

AAttttaacchhiinngg tthhee CCeenntteerr LLeegg BBrraaccee

Figure 2-6

1. Remove the accessory tray knob and washer from the central rod.

2. Slide the accessory tray over the central rod so that each arm of the tray is pushing against the inside of the

tripod legs.

3. Thread the accessory tray knob onto the central rod and tighten.

IInnssttaalllliinngg tthhee CCoouunntteerrwweeiigghhtt BBaarr

To properly balance the telescope, the mount comes with a counterweight bar and two counterweights. To install
the counterweight bar:

1. Remove the counterweight safety screw from the counterweight bar (opposite of the threaded end).

2. Thread the counterweight bar through the counterweight bar locking nut.

3. Locate the opening in the equatorial mount on the DEC axis.

4. Thread the counterweight bar into the opening until tight.

5. Tighten the counterweight bar lock nut fully for added support (see fig 2-7).

Once the bar is securely in place you are ready to attach the counterweights.

Counterweight Bar
Locking Nut

Counterweight Locking
Screw

Safety Screw

Tripod

Mounting Knob

Central Rod

Accessory Tray

Accessory Tray Knob

Figure 2-7

Counterweights

Counterweight
Bar

- 10 -

Since the fully assembled telescope can be quite heavy, position the mount so that the polar axis is pointing
towards north before the tube assembly and counterweights are attached. This will make the polar
alignment procedure much easier.

IInnssttaalllliinngg tthhee CCoouunntteerrwweeiigghhttss

Each Omni mount comes with two counterweights (One weighs 7 lbs./3.2kg and the other weighs 4 lbs./1.8kg). To
install the counterweights:

1. Orient the mount so that the counterweight bar points toward the ground.

2. Loosen the locking screw on the side of the counterweights (it doesn’t matter which counterweight you attach
first) so that the threads do not protrude through the center hole of the counterweight.

3. Slide the counterweight onto the shaft (see Figure 2-7).

4. Tighten the locking screw on the side of the weight to hold the counterweight in place.

5. Slide the second counterweight onto the shaft and tighten as in # 4.

6. Replace the counterweight safety screw.

AAttttaacchhiinngg tthhee SSllooww MMoottiioonn CCoonnttrrooll KKnnoobbss ((CCaabblleess))

The Omni mount comes with two slow motion control knobs (cables) that allows you to make fine pointing
adjustments to the telescope in both R.A. and Declination. To install the knobs:

1. Locate the two knobs (one is longer than the other
and is for the R.A. axis). Make sure the screw on
each knob does not protrude through the knob shaft
opening. Use the supplied Phillips head
screwdriver.

2. Line up the flat area on the inner portion of the
R.A. slow motion knob with the flat area on the
R.A. shaft.

3. Slide the R.A. slow motion knob onto the R.A.

shaft. There are two R.A. shafts, one on either side
of the mount. It makes no difference which shaft

you use since both work the same. Use
whichever one you find more convenient. If
after a few observing sessions you find the R.A.
slow motion knob is more accessible from the
other side, reinstall it on the opposite side.

4. Tighten the screw on the R.A. knob to hold it
securely in place.

Figure 2-8b

Declination Shaft

R.A. Shaft

Figure 2-8a

Declination Knob

R.A. Knob

- 11 -

m

t

5. The DEC slow motion knob attaches in the same manner as the R.A. knob. The shaft that the DEC slow
motion knob fits over is toward the top of the mount, just below the telescope mounting platform. Once again,
you have two shafts to choose from. Use the shaft that is pointing toward the ground. This makes it easy to
reach while looking through the telescope, something which is quite important when you are observing but
again if it is more convenient for you to use, then reinstall the knob position that suits your needs.

6. Put the polar axis cap over the polar axis. It is held into place by a tension fit.

AAttttaacchhiinngg tthhee TTeelleessccooppee TTuubbee ttoo tthhee MMoouunntt

The telescope optical tube attaches to the mount via a dovetail slide bar mounting bracket. For the refractors and the
Newtonian, the mounting bracket is the long bracket which is attached to the tube rings. For the Schmidt­Cassegrain the mounting bracket is attached along the bottom of the telescope tube. Before you attach the optical
tube, make sure that the declination and right ascension clutch knobs (clamps) are tight. This will ensure that
the mount does not move suddenly while attaching the telescope optical tube. To mount the telescope tube:

1. Remove the protective paper covering the optical
tube. You will have to remove the tube rings on the
refractors and Newtonian before removing the paper.

2. Loosen the mounting knob and the mounting safety
screw on the side of the mount platform so they do
not protrude into the mounting platform

Mounting Bracket

Tube Rings

3. Slide the dovetail mounting bracket into the recess on
the top of the mounting platform (see figure 2-9).

4. Tighten the mounting knob on the Omni mounting
platform to hold the telescope in place.

Mounting
Platfor

Telescope
Mounting
Screw

5. Hand tighten the mounting platform safety screw
until the tip touches the side of the mounting bracket.

Refractor Optical Tube is shown. The Newtonian and
Schmid

-Cassegrain attach similarly.

Figure 2-9

NOTE: Never loosen any of the knobs on the telescope tube or mount other than the R.A. and DEC knobs.

- 12 -

IInnssttaalllliinngg tthhee FFiinnddeerrssccooppee

To install the finderscope onto the telescope you must first mount the finderscope through the finder bracket and
then attach it to the telescope. Toward the rear of the telescope tube (on refractors and Schmidt-Cassegrain) and
front of the telescope tube (Newtonian), there is a small bracket with a set screw in it. This is where the finderscope
bracket will be mounted. To install the finderscope:

1. Loosen the finderscope adjustment screws so

they don’t protrude into the bracket. Then
slide the rubber O-ring over the eyepiece end
of the finderscope (smallest diameter side) and
roll it 2/3 of the way up into the slot (groove)
in the finderscope.

2. Insert the eyepiece end of the finderscope

through the narrow part of the bracket until the
O-ring presses tightly between the finder and
the inside of the bracket. Once it stops, then
pull outward on the spring loaded adjustment
screw and continue inserting the finderscope
until it is approximately centered in the
bracket.

3. Tighten the two adjustment screws until they

make contact with the finderscope body.

4. Locate the mounting bracket near the front (open) end of the telescope.

5. Loosen the set screw on the mounting bracket on the telescope so it

does not protrude into the bracket.

6. Slide the finder bracket (attached to the finderscope) into the mounting bracket on the telescope.

7. The finderscope bracket will slide in from the back. The finderscope should be oriented so that the

objective lens is toward the front (open) end of the telescope.

8. Tighten the set screw on the mounting bracket to hold the finderscope in place.

For information on aligning your finderscope, see the Telescope Basics section of this manual.

IInnssttaalllliinngg tthhee VViissuuaall BBaacckk

Finder

Bracket

Finderscope

Figure 2-10

Mounting

Bracket

Set
Screw

Only applicable to the Schmidt-Cassegrain, the Visual Back is the accessory that allows you to attach all visual
accessories to the telescope. The Omni Schmidt-Cassegrain normally comes with the Visual Back installed. If in
case it is not installed, follow these instructions for attaching it:

1. Remove the cover on the rear cell and then place the knurled slip ring on the Visual Back over the threads

on the rear cell (Fig 2-11).

2. Hold the Visual Back with the set screw in a convenient position and rotate the knurled slip ring clockwise

until tight. Once this is done, you are ready to attach other accessories, such as diagonals (for refractors
and the Schmidt-Cassegrain), eyepieces, etc. If you want to remove the Visual Back, rotate the slip ring
counterclockwise until it is free of the rear cell.

- 13 -

IInnssttaalllliinngg tthhee SSttaarr DDiiaaggoonnaall

The Star Diagonal is a prism that diverts the light at a right angle to the light path of refractors and Schmidt­Cassegrain telescopes. This allows you to observe in positions that are
physically more comfortable than if you looked straight through. To
attach the Star Diagonal onto the optical tube of a Schmidt-Cassegrain:

Eyepiece

1. Turn the set screw on the visual back until its tip no longer extends
into (i.e., obstructs) the inner diameter of the visual back.

2. Slide the chrome portion of the Star Diagonal into the visual back.

3. Tighten the set screw on the visual back to hold the Star Diagonal
in place.

If you wish to change the orientation of the Star Diagonal, loosen the
set screw on the visual back until the Star Diagonal rotates freely.
Rotate the diagonal to the desired position and tighten the set screw.

Refractors – To use the Star Diagonal with refractor telescopes, insert it into the 1 ¼” eyepiece adapter.

IInnssttaalllliinngg tthhee EEyyeeppiieecceess

The eyepiece, or ocular as it is also called, is an optical element that magnifies the image focused by the telescope.
Without the eyepiece it would be impossible to use the telescope visually. The eyepiece fits directly into the focuser
of refractors and the Newtonian or into the visual back on the Schmidt-Cassegrain. To attach an ocular:

1. Loosen the set screw on the eyepiece
adapter so that it does not obstruct the
inner diameter of the barrel.

2. Slide the chrome portion of the eyepiece
into the focuser.

3. Tighten the set screw to hold the eyepiece
in place.

To remove the eyepiece, loosen the set screw
on the focuser and slide the eyepiece out. You
can replace it with another ocular.

Figure 2-12

Many times it will be more comfortable to use a star diagonal on the refractors and Schmidt-Cassegrain for most
areas of the sky. To install an eyepiece into the star diagonal:

A. Loosen the set screw on the star diagonal until the tip no longer extends into the inner diameter of

the eyepiece end of the diagonal.

B. Slide the chrome portion of the eyepiece into the star diagonal.
C. Tighten the set screw on the star diagonal to hold the eyepiece in place.
D. To remove the eyepiece, loosen the set screw on the star diagonal and slide the eyepiece out. You

can replace it with other optional eyepieces.

Focuser Knob

Star
Diagonal

Visual Back

Focuser Tension
Screw

Figure 2-11

1 ¼" Eyepiece
Adapter

2" Focuser
Barrel

T-Adapter

- 14 -

The refracting telescopes can use eyepieces and diagonals of a 2” barrel diameter. To use a 2” barrel eyepiece, the
1¼” eyepiece adapter must first be removed. To do this, simply loosen the two chrome thumbscrews located around
the focuser barrel (see figure 2-12) and remove the 1 ¼” adapter. Once removed, a 2” eyepiece or accessory can be
inserted directly into the focuser barrel and secured with the two thumb screws.

Eyepieces are commonly referred to by focal length and barrel diameter. The focal length of each eyepiece is
printed on the eyepiece barrel. The longer the focal length (i.e., the larger the number) the lower the eyepiece
magnification (i.e., power) and the shorter the focal length (i.e., the smaller the number) the higher the
magnification. Generally, you will use low-to-moderate power when viewing. For more information on how to
determine power, see the section on “Calculating Magnification.”

MMoovviinngg tthhee TTeelleessccooppee MMaannuuaallllyy

In order to properly balance your telescope, you will need to move your telescope manually at various portions of
the sky to observe different objects. To make rough adjustments, loosen the R.A. and DEC clutch knobs slightly
and move the telescope in the desired direction.

Both the R.A. and DEC axis have lock levers to clutch down each axis of the telescope. To loosen the clutches on
the telescope, rotate the lock levers counterclockwise.

BBaallaanncciinngg tthhee MMoouunntt iinn RR..AA..

To eliminate undue stress on the mount, the telescope should be properly balanced around the polar axis in R.A. In
addition, proper balancing is crucial for accurate tracking if using an optional motor drive. To balance the mount:

1. Release the R.A. Clamp (see figure 2-13) and position the telescope off to one side of the mount (make sure
that the mounting bracket screw is tight). The counterweight bar will extend horizontally on the opposite side
of the mount (see figure 2-14).

2. Release the telescope — GRADUALLY — to see which way the telescope “rolls.”

3. Loosen the counterweight locking screw on the counterweight.

4. Move the counterweights to a point where they balance the telescope (i.e., it remains stationary when the R.A.
clamp is released).

5. Tighten the locking screw to hold the counterweights in place.

These are general balance instructions and will reduce undue stress on the mount. When taking
astrophotographs, this balance process should be done for the specific area at which the telescope is
pointing.

DEC Clamp

Figure 2-13

R.A. Clamp

- 15 -

BBaallaanncciinngg tthhee MMoouunntt iinn DDEECC

The telescope should also be balanced on the declination axis to prevent any sudden motions when the DEC clamp
(Fig 2-13) is released. To balance the telescope in DEC (all telescopes except the SCT):

1. Release the R.A. clamp and rotate the telescope so that it is on one side of the mount (i.e., as described in the
previous section on balancing the telescope in R.A.).

2. Lock the R.A. clamp to hold the telescope in place.

3. Release the DEC clamp and rotate the telescope until the tube is parallel to the ground (see figure 2-15).

4. Release the tube — GRADUALLY — to see which way it rotates around the declination axis. DO NOT LET

GO OF THE TELESCOPE TUBE COMPLETELY!

5. Loosen the screws that hold the telescope tube inside the mounting rings and slide the telescope either forwards
or backwards until it remains stationary when the DEC clamp is released.

6. Tighten the tube ring screws firmly to hold the telescope in place.

Note: The Omni XLT150R is the most difficult to balance depending on the latitude, the accessories used, and

which part of the sky the telescope is pointing to. Balance this telescope as best you can.

Figure 2-14

Like the R.A. balance, these are general balance instructions and will reduce undue stress on the mount. When
taking astrophotographs, this balance process should be done for the specific area at which the telescope is pointing.

AAddjjuussttiinngg tthhee MMoouunntt

In order for a motor drive to track accurately, the telescope’s axis of rotation must be parallel to the Earth’s axis of
rotation, a process known as polar alignment. Polar alignment is achieved NOT by moving the telescope in R.A. or
DEC but by adjusting the mount vertically, which is called altitude, and horizontally, which is called azimuth. This
section simply covers the correct movement of the telescope during the polar alignment process. The actual process
of polar alignment is making the telescope’s axis of rotation parallel to the Earth’s, is described later in this manual
in the section on “Polar Alignment.”

- 16 -

Figure 2-15

AAddjjuussttiinngg tthhee MMoouunntt iinn AAllttiittuuddee

• To increase the latitude of the polar axis, tighten the rear latitude adjustment screw and loosen the front screw
(if necessary).

• To decrease the latitude of the polar axis, tighten the front (under the counterweight bar) latitude adjustment
screw and loosen the rear screw (if necessary).

The latitude adjustment on the Omni mount has a range from approximately 20° to 60°.

It is best to always make final adjustments in altitude by moving the mount against gravity (i.e. using the rear
latitude adjustment screw to raise the mount). To do this you should loosen both latitude adjustment screws and
manually push the front of the mount down as far as it will go. Then tighten the rear adjustment screw to raise the
mount to the desired latitude.

Front Latitude
Adjustment Screw

Azimuth
Adjustment Screw

AAddjjuussttiinngg tthhee MMoouunntt iinn AAzziimmuutthh

For rough adjustments in azimuth, simply pick up the telescope and tripod and move it. For fine adjustments in
azimuth:

• Turn the azimuth adjustment knobs located on either side of the azimuth housing (see Fig 2-16). While

standing behind the telescope, the knobs are on the front of the mount.

• Turning the right adjustment knob clockwise moves the mount toward the right.

• Turning the left adjustment knob clockwise moves the mount to the left.

Both screws push off of the peg on the tripod head, which means you may have to loosen one screw while
tightening the other. The screw that holds the equatorial mount to the tripod may have to be loosened slightly.

Keep in mind that adjusting the mount is done during the polar alignment process only. Once polar aligned, the
mount must NOT be moved. Pointing the telescope is done by moving the mount in right ascension and
declination, as described earlier in this manual.

Rear Latitude Adjustment
Screw

Figure 2-16

- 17 -

A telescope is an instrument that collects and focuses light. The nature of the optical design determines how the
light is focused. Some telescopes (known as refractors) use lenses and other telescopes, known as reflectors
(Newtonians), use mirrors. Then, the Schmidt-Cassegrain telescope uses both mirrors and lenses. Each optical
design is briefly discussed below:

Developed in the early 1600s, the refractor is the oldest telescope design. It derives its name from the method it
uses to focus incoming light rays. The refractor uses a lens to bend or refract incoming light rays, hence the name
(see Figure 3-1). Early designs used single element lenses. However, the single lens acts like a prism and breaks
light down into the colors of the rainbow, a phenomenon known as chromatic aberration. To get around this
problem, a two-element lens, known as an achromat, was introduced. Each element has a different index of
refraction allowing two different wavelengths of light to be focused at the same point. Most two-element lenses,
usually made of crown and flint glasses, are corrected for red and green light. Blue light may still be focused at a
slightly different point.

A Newtonian reflector uses a single concave mirror as its primary mirror. Light enters the tube traveling to the
mirror at the back end. There light is bent forward in the tube to a single point, its focal point. Since putting your
head in front of the telescope to look at the image with an eyepiece would keep the reflector from working, a flat
mirror called a diagonal intercepts the light and points it out the side of the tube at right angles to the tube. The
eyepiece is placed there for easy viewing.

Newtonian Reflector telescopes replace heavy lenses with mirrors to collect and focus the light, providing much
more light-gathering power for the dollar. Because the light path is intercepted and reflected out to the side, you can
have focal lengths up to 1000mm and still enjoy a telescope that is relatively compact and portable. A Newtonian
Reflector telescope offers such impressive light-gathering characteristics you can take a serious interest in deep
space astronomy even on a modest budget. Newtonian Reflector telescopes do require more care and maintenance
because the primary mirror is exposed to air and dust. However, this small drawback does not hamper this type of
telescope’s popularity with those who want an economical telescope that can still resolve faint, distant objects.

AA ccuuttaawwaayy vviieeww ooff tthhee lliigghhtt ppaatthh ooff tthhee RReeffrraaccttoorr o

Figure 3-1

o

ppttiiccaall ddeessiiggn

n

- 18 -

AA ccuuttaawwaayy vviieeww ooff tthhee lliigghhtt ppaatthh ooff tthhee NNeewwttoonniiaann o

Figure 3-2

o

ppttiiccaall ddeessiiggn

n

The Schmidt-Cassegrain optical system (Schmidt-Cass or SCT for short) uses a combination of mirrors and lenses
and s referred to as a compound or catadioptric telescope. This unique design offers large-diameter optics while
maintaining very short tube lengths, making them extremely portable. The Schmidt-Cassegrain system consists of a
zero power corrector plate, a spherical primary mirror, and a secondary mirror. Once light rays enter the optical
system, they travel the length of the optical tube three times.

Inside the optical tube, a black tube extends out from the center hole in the primary mirror. This is the primary
baffle tube and it prevents stray light from passing through to the eyepiece or camera.

AA ccuuttaawwaayy vviieeww ooff tthhee lliigghhtt ppaatthh ooff tthhee SScchhmmiiddtt--CCaas

Figure 3-3

s

sseeggrraaiinn ooppttiiccaall ddeessiiggn

n

- 19 -