Cedar Ridge RHFD400RT-M-M, CRHFD400RT-M-M User Manual

This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to Air For Combustion and Ventilation section on page 8 of this manual.

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.

LS-SSFBD400RT-M-M-1103

Questions, problems, missing parts? Before returning to your retailer, contact our customer service department at 1-866-573-0674, 8:00 a.m - 4:30 p.m., EST, Monday - Friday or e-mail customerservice@usaprocom.com.

WARNING: This appliance is equipped for (Natural and Propane) gas. Field conversion is not permitted other than between natural or propane gases.

ITEM #0328248

VENT-FREE

GAS FIREPLACE INSERT

MODEL #CRHFD400RT-M-M

CAUTION - FOR YOUR SAFETY

Cedar Ridge

h e a r t h

Español p. 34

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE.

– Do not store or use gasoline or other ammable vapors and liquids in vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department. – Installation and service must be performed by a qualied installer, service agency or the gas supplier.

This appliance may be installed in an aftermarket, permanently located manufactured

(mobile) home, where not prohibited by local codes. This appliance is only for use

with propane or natural gas. This appliance is equipped with a simple means to

switch between propane and natural gas. Field conversion by any other means

including the use of a kit is not permitted.

ITEM #0328248 VENT FREE GAS FIREPLACE

Input Rating 32,000 BTU/Hr 32,000 BTU/Hr Gas Type Natural LP/Propane Ignition Piezo/Automatic Piezo/Automatic Manifold Pressure 4 in. W.C. 9 in. W.C. Inlet Gas Pressure (*For purpose of inlet adjustment) Maximum 10.5 in. 14 in. Minimum 5 in. 11 in. Dimension, inches (H x W x D) Heater 29.5 in. x 29.1 in. x 15.6 in. Carton 31.1 in. x 31.5 in. x 18.1 in. Weight, lbs. Stove 69.5 Shipping 79.5

Safety Information...........................................................................................................................3

Product Features.............................................................................................................................6

Air For Combustion and Ventilation.................................................................................................8

Installation .....................................................................................................................................11

Installing Logs................................................................................................................................18

Operation.......................................................................................................................................19

Care and Maintenance...................................................................................................................25

Troubleshooting.............................................................................................................................27

Replacement Parts........................................................................................................................31

WARNING: Read the installation & operation instructions before using

this appliance.

IMPORTANT: Read instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible re hazard and will void the warranty.

PRODUCT SPECIFICATIONS

TABLE OF CONTENTS

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, re, explosion, electrical shock, and carbon monoxide poisoning.

Only a qualied installer, service agent, or local gas supplier may install and service this product.

WARNING: Do not store or use gasoline or other ammable vapors or liquids in the

vicinity of this or any other appliance.

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning resemble the u with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get fresh air immediately! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease, people who are anemic, those under the inuence of alcohol, and those living in high altitudes.

NATURAL AND PROPANE/LP GAS: Natural and Propane/LP gases are odorless. An odormaking agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists. Make certain you read and understand all warnings. Keep this manual for reference. It is your guide to operating this heater safely.

WARNING: Any change to this replace or its controls can be dangerous.

WARNING: Do not use a blower insert, heat exchange insert or other accessory not

approved for use with this heater.

Due to high temperatures, the appliance should be located out of trafc and away from furniture and draperies. Do not place clothing or other ammable material on or near the appliance. Never place any objects in the heater. Heater becomes very hot when running heater. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a time after shutdown. Allow surfaces to cool before touching. Carefully supervise young children when they are in the room with the heater.

You must operate this heater with screen in place. Keep the heater area clear and free from combustible materials, gasoline, and other ammable vapors and liquids.

WARNING: Do not allow fans to blow directly into replace. Avoid any drafts that alter

burner ame patterns.

SAFETY INFORMATION

WARNING: This appliance can be used with propane or natural gas. It is shipped from the

factory adjusted for use with propane.

1. Do not place Propane/LP supply tank(s) inside any structure. Propane/LP supply tank(s) must be placed outdoors.

2. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shut-off system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, pages 8 through 10. If heater keeps shutting off, see Troubleshooting, pages 27 through 29.

3. Keep all air openings in front and bottom of heater clear and free of debris. This will ensure enough air for proper combustion.

4. If heater shuts off, do not relight until you provide fresh, outside air. If heater keeps shutting off, have it serviced.

5. Do not run heater:

• Where ammable liquids or vapors are used or stored.

• Under dusty conditions.

6. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

7. Always run heater with control knob at PILOT or ON locked positions. Never set control knob between locked positions. Poor combustion and higher levels of carbon monoxide may result.

8. Do not use heater if any part has been under water. Immediately call a qualied service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under water.

9. Turn off and unplug heater and let cool before servicing. Only a qualied service person should service and repair heater.

10. Operating heater above elevations of 4,500 ft. could cause pilot outage.

11. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lb. capacity.

12. This heater should not be installed in a bedroom or bathroom.

13. Do not use this heater as a wood-burning heater. Use only the logs provided with the heater.

14. To prevent sooting, follow the instructions in Care and Maintenance (page 25).

15. Do not add extra logs or ornaments such as pine cones, vermiculite, or rock wool. Using these added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into the control area of heater. After servicing, always replace screen before operating heater.

16. This heater is designed to be smokeless. If logs ever appear to smoke, turn off heater and call a qualied service person. Note: During initial operation, slight smoking could occur due to log curing and the heater burning manufacturing residues.

QUALIFIED INSTALLING AGENCY

Only a qualied agency should perform installation and replacement of gas piping, gas utilization equipment or accessories, and repair and servicing of equipment. The term “qualied agency” means any individual, rm, corporation, or company that either in person or through a representative is engaged in and is responsible for: a) Installing, testing, or replacing gas piping or b) Connecting, installing, testing, repairing, or servicing equipment; that is experienced in such work; that is familiar with all precautions required; and that has complied with all the requirement of the authority having jurisdiction.

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater is equipped with an electronic piezo control system. This system requires AAA batteries (provided).

2 GAS OPTIONS CAPABLE

Your heater is equipped to operate on either propane or natural gas. The heater is shipped from the factory ready for connecting to propane. The heater can easily be changed to natural gas by having your qualied installer follow the instructions on page 16 and the markings on the heater.

State of Massachusetts: The installation must be made by a licensed plumber or gas tter in the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-red supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

In the State of Massachusetts, unvented propane or natural gas-red space heaters shall be prohibited in bedrooms and bathrooms.

In the State of Massachusetts the gas cock must be a T-handle type. The State

of Massachusetts requires that a exible appliance connector cannot exceed

three feet in length.

LOCAL CODES

Install and use heater with care. Follow all codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code, ANSI Z223.1, also known as NFPA 54*.

*Available from: American National Standard Institute, Inc National Fire Protection Association, Inc. 1430 Broadway 1 Batterymarch Park New York, NY 10018 Quincy, MA 02269-9101

This heater is designed for vent-free operation. State and local codes in some areas prohibit the use of vent-free heaters.

PRODUCT FEATURES

UNPACKING

1. Remove top inner pack.

2. Tilt carton so that heater is upright.

3. Remove protective side packaging.

4. Slide heater out of carton.

5. Remove protective plastic wrap.

6. Hold the screen, lift, and pull forward.

7. Remove log set by cutting plastic ties.

8. Carefully unwrap log.

9. Check for any shipping damage. If heater or log is damaged, promptly inform your dealer where you bought the heater.

PRODUCT IDENTIFICATION

Fig. 1

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30 mL) of water for every 1,000 BTUs (.3 kw) of gas input per hour. An unvented room heater is recommended as a supplemental heater (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather. The following steps will help ensure that water vapor does not become a problem:

1. Be sure the heater is the proper size for the application, including adequate combustion air and circulation air.

2. If there is high humidity, a dehumidier may be used to help lower the water vapor content of the air.

3. Do not use an unvented room heater as the primary heat source.

Hood

Screen

Logs

Heater Controls (Inside Panel)

AIR FOR COMBUSTION AND VENTILATION

WARNING: If the area in which the heater may be operated does not meet the required

volume for indoor combustion air, combustion and ventilation air shall be provided by one of the methods described in the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or applicable local codes.

PRODUCING ADEQUATE VENTILATION

All spaces in homes fall into one of the three following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space The information on pages 8 through 9 will help you classify your space and provide adequate ventilation.

Conned and Unconned Space

A conned space is a space whose volume is less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw) of the aggregate input rating of all appliances installed in that space and an unconned space as a space whose volume is not less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms connecting directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconned space. This heater shall not be installed in a conned space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. * Adjoining rooms are connecting only if there are door-less passageways or ventilation grills between them

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air. Unusually tight construction is dened as construction where: a) walls and ceilings exposed to the outside atmosphere have a continuous water vapor

retarder with a rating of one perm (6x10

-11

kg per pa-sec-m2) or less with openings

gasket or sealed and b) weather stripping has been added on windows that can be opened and on doors and c) caulking or sealants are applied to areas such as joints around window and door frames,

between sole plates and oors, between wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical, and gas lines, and at other openings. If your home meets all of the three criteria above, you must provide additional fresh air. See “Ventilation Air From Outdoors” (page 10). If your home does not meet all of the three criteria above, proceed to “Determining Fresh-Air Flow For Heater Location”.

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Conned or Unconned Space

Use this worksheet to determine if you have a conned or unconned space. Space: Includes the room in which you will install heater plus any adjoining rooms with door-less passageways or ventilation grills between the rooms.

1. Determine the volume of the space Length × Width × Height = cu. ft. (volume of space) Example: Space size 20 ft. (length) × 16 ft.(width) × 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Divide the space volume by 50 cu. ft. to determine the maximum BTU/hr the space can support.

_______ (volume of space) ÷ 50 cu. ft.= (Maximum BTU/hr the space can support) Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum BTU/hr the space can support)

3. Add the BTU/hr of all fuel burning appliances in the space. Vent-free heater ________ BTU/hr Gas water heater* _______BTU/hr Gas furnace ___________ BTU/hr Vented gas heater _______BTU/hr Example: Gas heater logs ________ BTU/hr Gas water heater 30,000 BTU/hr Other gas appliances*+ ___BTU/hr Vent-free heater + 26,000 BTU/hr Total =________________ BTU/hr Total = 56,000 BTU/hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum BTU/hr the space can support with the actual amount of BTU/hr used.

_______ BTU/hr (maximum the space can support) _______ BTU/hr (actual amount of BTU/hr used). Example : 51,200 BTU/hr (maximum the space can support) 56,000 BTU/hr (actual amount of BTU/hr used) The space in the above example is a conned space because the actual BTU/hr used is more than the maximum BTU/hr the space can support. You must provide additional fresh air. Your options are as follows: a) Rework worksheet, adding the space of an adjoining room. If the extra space

provides an unconned space, remove door to adjoining room or add ventilation grills between rooms. See “Ventilation Air From Inside Building,” page 10.

b) Vent room directly to the outdoors. See “Ventilation Air From Outdoors”, page 10. c) Install a lower BTU/hr heater if lower BTU/hr size makes room unconned. If the

actual BTU/hr used is less than the maximum BTU/hr the space can support, the space is an unconned space. You will need no additional fresh air ventilation.

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or duct. You must provide two permanent openings: one within 12 in. of the ceiling and one within 12 in. of the oor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code NFPA 54/ANS Z223.1. Air for Combustion and Ventilation for required size of ventilation grills or ducts.

Ventilation Air From Inside Building

This fresh air would come from adjoining unconned space. When ventilating to an adjoining unconned space, you must provide two permanent openings: one within 12 in. of the wall connecting the two spaces (see options 1 and 2, Fig. 2). You can also remove door into adjoining room (see option 3, Fig. 2). Follow the National Fuel Gas Code NFPA 54/ANS Z223.1. Air for Combustion and Ventilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. Rework worksheet, adding the space of the adjoining unconned space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

Fig. 2 - Ventilation Air from Inside Building

Fig. 3 - Ventilation Air from Outdoors

WARNING: If the area in which the heater may be operated does not meet the required volume for indoor combustion air, combustion and ventilation air shall be provided by one of the methods described in the NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, the INTERNATIONAL FUEL GAS CODE, or applicable local codes.

Outlet

Air

Inlet

Air

Ventilation

Grills

Into Adjoining

Room,

Option 1

Remove

Door

Into

Adjoining

Room,

Option 3

Ventilation Grills

Into adjoining Room,

Option 2

12 in.

Outlet

Air

Ventilated

Attic

To Attic

Crawl

Space

Inlet Air

Ventilated

Crawl Space

Fig. 4 - Minimum Clearance to Wall and Ceiling

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along

with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house.

WARNING: A qualied technician must install heater. Follow all local codes.

WARNING: Never install the heater:

• in a bedroom or bathroom

• in a recreational vehicle

• where curtains, furniture, clothing, or other ammable objects are less than 42 in. from the front, top or sides of the heater.

• in high trafc areas

• in windy or drafty areas

CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater where impurities (such as tobacco smoke, aromatic candles, cleaning uids, oil or kerosene lamps, etc.) in the air exist, may cause walls to discolor.

WARNING: Maintain the minimum clearances. If you can, provide greater clearances from oor, ceiling and adjoining side and back walls.

IMPORTANT: Vent-free heaters add moisture to the air. Although this is benecial, installing heater in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 8 through 10.

CHECK GAS TYPE

Use only the type of gas indicated on the plate. If your gas supply cannot meet that requirement, do not install heater.

CLEARANCES TO COMBUSTIBLES

Carefully follow the instructions below. This heater is a wall mount unit designed to sit directly on the oor or on a mantel base.

IMPORTANT: You must maintain minimum wall and ceiling clearances during installation. The minimum clearances are shown in Fig. 4. Measure from outermost point of heater.

Minimum Wall and Ceiling Clearances (see Fig. 4)

A. Clearances from outermost point of heater to any combustible side wall should not be less than 12 in. B. Clearances from the heater to the ceiling should not be less than 48 in.

Ceiling

Side Wall

12 in

Minimum

12 in

Minimum

48 in

Minimum

Side Wall

Front View

Fig. 5 - Gas Regulator Location and Gas Line

Access Into Stove Cabinet

Fig. 6 - External Regulator With Vent Pointing Down

CONNECTING TO GAS SUPPLY

WARNING: A qualied technician must connect heater to gas supply. Follow all local

codes.

WARNING: This appliance requires a 3/8 in. NPT inlet connection to pressure regulator

(see Fig. 5).

CAUTION: Never connect heater directly to the gas supply. This heater requires an external regulator (not supplied). The external regulator between the gas supply and heater must be installed. Gas supplier provides external regulator for natural gas.

INSTALLATION ITEMS NEEDED

Before installing heater, make sure you have the items listed below.

• piping (check local codes) sealant

• (resistant to propane/LP gas)

• equipment shutoff valve*

• test gauge connection**

• sediment trap

• tee joint

• pipe wrench

• exible gas hose (check local code) A CSA design-certied equipment shutoff valve with 1/8 in. NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design certied equipment shutoff valve from your dealer.

WARNING: Never connect heater to private (non-utility) gas wells. This gas is commonly

known as wellhead gas.

The installer must supply an external regulator for liquid propane. The external regulator is provided by the gas supplier for natural gas. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11 and 14 in. of water column for propane and between 5 and 10.5 in. of water column for natural gas. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install external regulator with the vent pointing down as shown in Fig. 6. Pointing the vent down protects it from freezing rain or sleet.

Propane/LP Supply Tank

External Regulator

Propane/LP Supply Tank

Vent Pointing Down

Gas regulator Inlet connector

CAUTION: Use only new black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of ½ in. diameter or greater to allow proper volume gas to heater. If pipe is too small, loss of pressure will occur. Installation must include an equipment shutoff valve, union, and plugged 1/8-in. NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Fig. 7).

IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance. Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

CAUTION: Use pipe joint sealant that is resistant to gas (PROPANE or NG). We recommend that you install a sediment trap in a supply line as shown in Fig. 7. Locate sediment trap where it is within reach for cleaning and not likely to freeze. Install in the piping system between fuel supply and heater. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed incorrectly, heater may not run properly.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting into gas piping and/or ttings. NG Models: 5 in. to 10.5 in. W.C. Gas supplier provide external regulator for natural gas.

*Purchase the optional CSA design-certied equipment shutoff valve from your dealer. ** Minimum inlet pressure for purpose of input adjustment.

Fig. 7 - Gas Connection

3 in. Minimum**

Test

Gauge Connection *

Sediment Trap

Tee Joint Reducer Bushing to 1/8 in. NPT 1/8 in. NPT Plug Tap

Tee Joint Pipe Nipple Gap

3/8 in. NPT Pipe Nipple

Ground Joint Union

Equipment Shutoff Valve

Inlet Pipe From Gas Meter (11 in. W. C. to 14 in. W. C. Pressure)

CAUTION: Two gas line installations at the same time are prohibited. The access plate to the simple switching means shall not be opened while the heater is in operation.

This appliance can be used with propane or natural gas. It is shipped from the factory adjusted for use with propane. Only a qualied installer or service technician can perform gas selection and connecting to gas supply.

CAUTION: To avoid gas leakage at the inlet of regulator, a qualied installer or service technician must use steel or metal hex plug with sealant. Overtightening of inlet gas line can cause a crack in the internal regulator.

For changing from propane to natural gas supply

1. Remove bottom screw from cover plate, (see Fig. 8), and rotate to expose fuel selection device

2. For NATURAL GAS, press in knob using a at screwdriver with a blade the width of a quarter and turn knob clockwise until the knob locks into the NG position (see Fig. 9).

3. Rotate and close cover over fuel selection device and reinstall screw.

4. Remove steel or metal hex plug (with wrench provided) from natural gas inlet of regulator and install into LP inlet of regulator, use thread sealant to assure there are no leaks.

For changing from natural gas supply to propane supply

1. Remove bottom screw from cover plate, (see Fig. 8), and rotate to expose fuel selection device.

2. For PROPANE GAS, press in knob using a at screwdriver with a blade the width of a quarter and turn knob counterclockwise until the knob locks into the LP position (see Fig. 10). Fuel selection device must be locked into either the LP position or the NG position.

3. Rotate and close cover over fuel selection device and reinstall screw.

4. Remove steel or metal hex plug from LP gas inlet of regulator and install into NG inlet of regulator, use thread sealant to assure there are no leaks.

Fig. 8

Fig. 10

Fig. 9

NATURAL GAS PROPANE GAS

PLUG

NATURAL GAS PROPANE GAS

PLUG

NATURAL GAS PROPANE GAS

Fig. 11 - Equipment Shut -off Valve

Fig. 12 - Checking Gas Joints

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping and connections for leaks after installing or servicing.

Correct all leaks immediately.

WARNING: Never use an open ame to check for a leak. Apply a mixture of liquid

soap and water to all joints. If bubbles form, there may be a leak. Correct all leaks immediately.

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG ( 3.5kPa )

1. Disconnect heater with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 PSIG will damage heater regulator.

2. Cap off open end of gas pipe where equipment shutoff valve was connected.

3. Pressurize supply piping system by either using compressed air or opening gas supply tank valve.

4. Check all joints of gas supply piping system. Apply mixture of liquid soap and water to gas joints. If bubbles form, there may be a leak.

5. Correct all leaks immediately.

6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected ttings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1. Close equipment shutoff valve (see Fig. 11).

2. Pressure supply piping system by either using compressed air or opening gas supply tank valve.

3. Check all joints from gas meter to equipment shutoff valve (see Fig. 12). Apply mixture of liquid soap and water to gas joints. If bubbles form, there may be a leak.

4. Correct all leaks immediately.

Pressure Testing Heater Gas Connections

1. Open equipment shutoff valve (see Fig. 11).

2. Open gas supply tank valve.

3. Make sure control knob of heater is in the OFF position.

4. Check all joints from equipment shutoff valve to control valve (Fig. 12). Apply mixture of liquid soap and water to gas joints. If bubbles form, there may be a leak.

5. Light heater (see Operation, page 19). Check all other internal joints for leaks.

6. Turn off heater (see "To Turn Off Gas to Appliance," page 20).

Equipment Shutoff Valve

Open

Closed

External Regulator

Propane/LP Supply Tank

Control Valve Location

Equipment Shut Off Valve

Vent Pointing Down

Installation for Remote Receiver:

The remote receiver operates on four 1.5V AA-size batteries (included). It is recommended that ALKALINE batteries be used for longer battery life and maximum microprocessor performance. IMPORTANT: New or fully charged batteries are essential for proper operation of the remote receiver as the solenoid power consumption is higher than standard remote control systems.

1. Take Control Box out from Control Panel. (See Fig. 13)

2. Remove battery cover along the direction showed on the battery box, and install four (4) 5# batteries into the box. (See Fig. 14)

Fig. 13

Fig. 14

• Batteries are included.

• Remove batteries when depleted.

• Install/replace the batteries according to the type and quantity stated in table below.

• Do not mix old and new batteries. New batteries should be the same brand for best results.

• Be sure to observe proper polarity (+/-) when installing or replacing the batteries. Damage due to improper battery installation may void the warranty on the product.

• For remote control systems, maximize battery life by turning off the receiver when it is not in use.

• For long periods of non-operation, remove batteries from all components for safety.

BATTERY INSTRUCTIONS

Component Type of Battery Battery Qty.

Ignitor AAA 1 Remote Control AAA 2 or 3* Remote Receiver AA 4

*Note: Quantity depends on model of remote control.

INSTALLING LOGS

Fig. 15 - Installing Log Set

IMPORTANT: Make sure log does not cover any burner ports (see Fig. 15). It is very important to install the logs exactly as instructed. Do not modify logs. Use only logs supplied with heater.

STEP 1: Install the log 1 onto the two slots in middle plate.

All logs

STEP 2: Install log 2 onto two slots in left plate. Install log 3 onto the two slots in right plate.

STEP 3: Install log 4 onto two slots in front plate.

WARNING: Failure to position the parts

in accordance with these diagrams or failure to use only parts specically approved with this heater may result in property damage or personal injury.

CAUTION: After installation, and periodically thereafter, check to ensure that no ame comes in contact with any log. With the heater set to high, check to see if ames contact any log. If so, reposition logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

2 3

STEP 4: Install the recessed holes bottom of log 5 onto the pins on log 2 and 4. Insert the recessed holes bottom of log 6 onto the pins on log 1 and 3.

OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a re or explosion may result

causing property damage, personal injury, or loss of life.

NOTICE: During initial operation of new heater, burning logs will give off a paper

burning smell. Orange ame will also be present. Open a window to vent smell. This will last only a few hours.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

A. This appliance has a pilot which must be lit by the electronic ignitor. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

C. Use only your hand to push control. Never use tools. If the appliance does not operate, don’t try to repair it. Call a qualied service technician or gas supplier. Forced or attempted repair may result in a re or explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualied service technician to inspect the appliance and to replace any part of the control system and any gas control, which has been under water.

Note: Please wait one minute after shutting off replace to allow the control valve to reset before starting again.

Fig. 16 - Control Knob Position

LIGHTING INSTRUCTIONS

1. Press the OFF button to let pilot stay.

2. Turn gas control knob clockwise to OFF position to shut off burner.

TO TURN OFF GAS TO APPLIANCE

Shutting off heater

1. STOP! Read the safety information on the front and back of the warning plate on page 19.

2. Make sure manual shutoff valve is fully open.

3. Unscrew ignitor cap and install an AAA type battery with the anode (+) pointing out. Replace cap.

4. Install two (2) AAA size batteries in the remote transmitter.

5. Be sure the slide switch on the front of the receiver box is in the REMOTE position.

6. Push in the control knob slightly and turn clockwise to the OFF position.

7. Wait ve (5) minutes to clear out out any gas. Then smell for gas around the heater and near the oor. If you smell gas, STOP! Follow "B" in the safety information on the rating plate. If you do not smell gas, go to the next step.

8. Push the control knob in slightly and turn counterclockwise to “PILOT” position and depress for ve (5) seconds. Note: The rst time the heater is operated after connecting the gas supply, the control knob should be depressed for about thirty (30) seconds. This will allow gas to bleed from the gas system.

9. With the control knob pushed in, push down and release the ignitor button.This will light the pilot. If needed, keep pressing the ignitor button until pilot lights.

10. Continue pushing the control knob in for an additional sixty (60) seconds to allow the thermocouple to warm up and to allow air to bleed from the gas system. Release the control knob. Note: If the pilot goes out, repeat steps 7, 8, 9 and 10.

11. Rotate the control knob counterclockwise to the ON position.

12. Press the LEARN BUTTON on the front of the remote receiver box until you hear a beep.

13. Press the ON button on the remote control transmitter to light the burner. (This will also “learn”, or program, the transmitter and the receiver).

14. If the transmitter is lost or damaged, the slide switch on the receiver can be used to operate the heater.

Ignitor

Control Case

Control Knob

On/Off Switch

REMOTE CONTROL OPERATION

This appliance must not be used with glass doors in the closed position. This can lead to pilot outages and severe sooting outside the replace. The transmitter operates on two AAA batteries. (Fig. 17)

KEY SETINGS ON - Operates unit to on position, Manually operated solenoid ON. OFF - Operates unit to off position, Manually operated solenoid OFF. MODE -Changes unit from manual mode to thermo mode. SET - Sets temperature in thermo mode.(Fig. 18)

LCD Liquid Crystal Display

1. DISPLAY Indicates CURRENT room temperature.

2. °F or °C Indicates degrees Fahrenheit or Celsius.

3. FLAME Indicates burner/valve in operation.

4. ROOM Indicates remote is in THERMO operation.

5. TEMP Appears during manual operation.

6. SET Appears during time the of setting the desired temperature in the thermo operation. (Fig. 19)

SETTING°F/°C SCALE

The factory setting for temperature is °F. To change this setting to°C . First Press the ON key and the OFF key on the transmitter at the same time this will change from°F to °C. Follow this same procedure to change from°C back to°F. (Fig. 20)

MANUAL FUNCTION

To operate the system in the manual “MODE” do the following.

ON OPERATION

Press the ON key and the appliance ame will come on. During this time the LCD screen will show ON (Fig. 21). After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (Fig. 22). (Flame icon will appear on LCD screen in manual on mode).

OFF OPERATION

Press the OFF key and the appliance ame will shut off. During this time the LCD screen will show OF (Fig. 23). After 3 seconds the LCD screen will default to display room temperature and the word TEMP will show (Fig. 24).

Fig. 17

Fig. 18

Fig. 19

Fig. 20

Fig. 21

MATCHING SECURITY CODES

When matching security codes, be sure slide button on the receiver is in the REMOTE position. To program the remote receiver to LEARN a new security code, press and release the LEARN button on the top of the remote receiver, and then press ON or OFF button on the transmitter. A change in the beeping pattern at the receiver, indicates the transmitter's code has been programmed into the receiver.

Fig. 22

Fig. 23

Fig. 24

THERMOSTAT FUNCTION SETTING DESIRED ROOM TEMPERATURE

This remote control system can control the thermostat when the transmitter is in the THERMO mode (The word ROOM must be displayed on the screen). To set the THERMO MODE and desired room temperature, Press the MODE key until the LCD screen shows the word ROOM. Then the remote is in the thermostatic mode. Press and hold the SET key until the desired set temperature is reached. (By pressing and holding the set key the LCD screen set numbers will increase from 45° to 99° and then restart over at 45°) Next release the SET key. The LCD screen will display the set temperature for 3 seconds and the LCD screen will ash the set temperature for 3 seconds. Then the LCD screen will default to display the room temperature.

TO CHANGE THE SET TEMPERATURE

Press and hold the SET key until the desired set temperature is reached. (By pressing and holding the set key the LCD screen set numbers will increase from 45° to 99° then restart over at 45°). Next release the SET key. The LCD screen will display the set temperature for 3 seconds. Then will ash the set temperature for 3 seconds. Then the LCD screen will default to display the room temperature. Press the MODE key to disengage the thermo mode. The word ROOM on the LCD screen will not show when the thermo is not in operation. Note: The highest SET temperature is 99°F (3 °C) and the lowest temperature is 45°F (6°C).

Fig. 25

Fig. 26

REMOTE CONTROL OPERATION NOTES:

The Thermo Feature on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a certain number of degrees from the SET TEMPERATURE. This variation is called the “SWING” or TEMPERATURE DIFFERENTIAL. The normal operating cycle of an appliance may be -4 times per hour depending on how well the room or home is insulated from the cold or drafts. The factory setting for the “swing number” is 2. This represents a temperature variation of +/-2°F (1°C) between SET temperature and ROOM temperature, which determines when the replace will be activated. The transmitter has ON and OFF manual functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed the word ON or OF will appear on the LCD screen to show while the signal is being sent. Upon initial use, there may be a delay of three seconds before the remote receiver will respond to the transmitter. This is part of the system’s design.

SETTING UP & USING YOUR REMOTE CONTROL SYSTEM

Notice: This guide is intended to provide supplemental information about setting up and

using the remote control that was included with your gas logs. It is not intended to replace the information in the Owners Manual. Please refer to the Owners Manual for detailed information about your appliance.

Install batteries. Batteries are required in both the Remote (2AAA size) and Receiver (4AA size). (See Fig. 27) Helpful Hint: Be sure batteries are placed correctly. Reversing the batteries can cause damage to the receiver and remote. Replace all batteries on a yearly basis or sooner.

Fig. 27

Fig. 28

Programming the Remote and Receiver

The remote and receiver must be “learned” to one another. Place the slide switch on the receiver in the Remote position.(See Fig. 28)

Programming the Remote and Receiver

Use a pen or small screwdriver to gently press and release the recessed Learn button on the face of the receiver (audible beep occurs). (See Fig. 29)

Fig. 29

ADJ.

LEARN

REMOTE

OFF

Fig. 30 Fig. 31

Programming the Remote and Receiver

Press the ON button on the remote (series of audible beeps occur). Your appliance should come on.(See Fig. 30) Helpful Hint: If your appliance does not come on check to make sure the control knob is in the “ON” position.

Setting The Temperature

Press the SET button to change the temperature setting. Release the SET button to choose the desired setting. Your unit will cycle on and off to maintain that selected setting.(See Fig. 31)

INSPECTING BURNERS

Check pilot ame pattern and burner ame patterns often.

PILOT FLAME PATTERN

1. Turn control knob to pilot position.

2. Inspect pilot ame and refer to Fig. 32 and 33.

• Fig. 32 shows a correct pilot ame pattern.

• Fig. 33 shows an incorrect pilot ame pattern. The incorrect pilot ame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down.

• If the pilot ame is incorrect, as shown in Fig. 33, turn heater off (see “To Turn Off Gas to Appliance, " page 20). See Troubleshooting, page 27 - 29.

Fig. 34 - Correct Pilot Flame Pattern with Control Knob Set to High Flame (5)

Fig. 35 - Incorrect Pilot Flame Pattern with Control Knob Set to High Flame (5)

BURNER FLAME PATTERN

Fig. 34 shows a correct burner ame pattern. Fig. 35 shows an incorrect burner ame pattern.

• If burner ame is incorrect, as shown in Fig. 35, turn heater off (see “To Turn Off Gas to Appliance”, page 20).

• see Troubleshooting, pages 27 through 29.

BURNER PRIMARY AIR HOLES

Air is drawn into the burner through the holes in the tting at the entrance to the burner. These holes may become blocked with dust or lint. Periodically inspect these holes for any blockage and clean as necessary. Blocked air holes will create soot.

Fig. 32 - Correct Pilot Flame Pattern

Fig. 33- Incorrect Pilot Flame Pattern

More than 8 in. above top of logs

Approx. 3-6 in. above top of logs

Fig. 36 - Injector holder on

CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

We recommend that you clean the unit every three months or after 2,500 hours of operation. We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2. Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Fig. 36).

3. Blow air through the ports/slots and holes in the burner.

4. Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5. Blow air into the primary air holes on the injector holder.

6. In case any large clumps of dust have now been pushed into the burner. Repeat steps 3 and 4. Clean the pilot assembly also.

WARNING: Failure to keep primary air openings of burners clean may result in sooting

and property damage.

CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualied service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning ame. Keep these holes clear of dust, dirt, and lint. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every 2,500 hours of operation or every three months.

MAIN BURNER

Periodically inspect all burner ame holes with the heater running. All slotted burner ame holes should be open with yellow ame present. All round burner ame holes should be open with a small blue ame present. Some burner ame holes may become blocked by debris or rust, with no ame present. If so, turn off the heater and let it cool, either remove blockage or replace burner. Blocked burner ame holes will create soot.

CARE AND MAINTENANCE

Injector

Primary Air Inlet Holes

Burner Tube

Fig. 37

CLEANING ODS/PILOT

Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean.

A yellow tip on the pilot ame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot ame comes out of the pilot assembly (see Fig. 37). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

CABINET

Air Passageways

● Use a vacuum cleaner or pressurized air, and a small soft bristled brush to clean. Exterior

● Use a soft cloth dampened with a mild soap and water mixture.

● Wipe the cabinet to remove dust.

LOGS

● If you remove logs for cleaning, refer to Installing Logs to properly replace logs.

● Replace log(s) if broken or chipped (dime-size or larger).

BLOWER - ITEM #0293809 (Optional Accessory Sold Separately)

Refer to blower manual.

NG Pilot Air Inlet Hole

Pilot Assembly

LP Pilot Air Inlet Hole

TROUBLESHOOTING

WARNING: If you smell gas:

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors.

WARNING: Make sure that power is turned off before proceeding.

WARNING: Turn off and let cool before servicing. Only a qualied service person should

service and repair heater.

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can

damage ODS/pilot unit.

Problem Possible Cause Corrective Action

When ignitor button is pressed in, there is no spark at ODS/pilot.

1. Ignitor electrode is positioned wrong.

2. Ignitor electrode is broken,

3. Ignitor electrode is not connected to ignitor cable.

4. Ignitor cable is pinched or wet.

5. Damaged ignitor cable.

6. Bad piezo ignitor.

7. Low battery.

1. Replace electrode.

2. Replace electrode.

3. Replace ignitor cable.

4. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry.

5. Replace ignitor cable.

6. Replace piezo ignitor.

7. Replace battery.

When ignitor button is pressed in, there is a spark at a ODS/pilot but no pilot ame present.

1. Gas supply is turned off or equipment shutoff valve is closed.

2. Control knob not fully pressed in while pressing ignitor button.

3. Air in gas lines (new installation or recent gas interruption).

4. ODS/pilot is clogged.

5. Incorrect inlet gas pressure or inlet regulator is damaged.

6. Depleted gas supply.

1. Turn on gas supply or open equipment shutoff valve.

2. Fully press in control knob while pressing ignitor button.

3. Continue holding down control knob for 30 seconds to remove air.Repeat igniting operation until air is removed.

4. Clean ODS/pilot (see Care and Maintenance, page 25) or replace ODS/pilot assembly.

5. Check inlet gas pressure or replace inlet gas regulator.

6. Contact local propane/LP Gas Company.

Problem Possible Cause Corrective Action

ODS/pilot lights but ame goes out when control knob is released.

1. Control knob is not fully pressed in.

2. Control knob is not pressed in long enough.

3. Equipment shut off valve is not fully open.

4. Thermocouple connection is loose.

5. Thermocouple damaged.

6. Control valve damaged.

1. Press in control knob fully.

2. After ODS/pilot lights, keep control knob pressed in 30 seconds.

3. Fully open equipment shutoff valve.

4. Hand tighten until snug, and then tighten ¼ turn more.

5. Replace thermocouple.

6. Contact customer service.

Burner(s) does not light after ODS/pilot is lit.

1. Burner orice is clogged.

2. Burner orice diameter is too small.

3. Inlet gas pressure is too low.

1. Clean Burner orice (see Care and Maintenance, page 25) or contact customer service.

2. Replace burner orice.

3. Contact your gas supplier.

Delayed ignition of burner(s).

1. Manifold pressure is too low.

2. Burner orice is clogged.

1. Contact your gas supplier.

2. Clean burner (see Care and Maintenance, page 25) or contact customer service.

Burner backring during combustion.

1. Burner orice is clogged or damaged.

2. Burner is damaged.

3. Gas regulator is damaged.

1. Clean burner orice (see Care and Maintenance, page 25) or Contact customer service.

2. Contact dealer or customer service.

3. Replace gas regulator.

High yellow ame during burner combustion.

1. Not enough air.

2. Gas regulator is defective.

3. Inlet gas pressure is too low.

1. Check burner for dirt and debris. If found, clean burner (see Care and Maintenance, page 25).

2. Replace gas regulator.

3. Contact your gas supplier.

Gas odor during combustion.

1. Foreign matter between control valve and burner.

2. Gas leak. (See Warning Statement at top of page

27).

1. Take apart gas tubing and remove foreign matter.

2. Locate and correct all leaks (see “Checking Gas Connections,” page 16).

Problem Possible Cause Corrective Action

Slight smoke or odor during initial operation.

1. Residues from Manufacturing process.

1. Problem will stop after a few hours of operation.

Heater produces a whistling noise when burner is lit.

1. Turning control knob to high (5) position when burner is cold.

2. Air in gas line.

3. Air passageways on heater are blocked.

4. Dirty or partially clogged burner orice.

1. Turn control knob to low (1) position and let warm up for a minute.

2. Operate burner until air is removed from line. Have gas line checked by local propane/LP gas company.

3. Observe minimum installation clearances (Fig. 4, page 11)

4. Clean burner (see Care and Maintenance, page 25) or contact customer service.

Heater produces a clicking/ticking noise just after burner is lit or shut off.

1. Metal is expanding while heating or contracting while cooling.

1. This is common with most heaters. If noise is excessive, contact qualied service technician.

White powder residue forming within burner box or on adjacent walls or furniture.

1. When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue.

1. Turn heater off when using furniture polish, wax, carpet cleaner, or similar products.

Heater produces unwanted odors.

1. Heater is burning vapors from paint, hair spray, glues, etc. (See IMPORTANT statement, page 27).

2. Gas leak. See Warning Statement at the top of page 27.

3. Low fuel supply.

1. Ventilate room. Stop using odor causing products while heater is running.

2. Locate and correct all leaks (see “Checking Gas Connections,” page 16).

3. Rell supply tank (Propane / LP models).

Heater shuts off in use (ODS operates).

1. Not enough fresh air is available.

2. Low line pressure.

3. ODS/pilot is partially clogged.

1. Open window and/or door for ventilation.

2. Contact local gas supplier.

3. Clean ODS/pilot (see Care and Maintenance, page 25).

Gas odor exists even when control knob is in OFF position.

1. Gas leak. See Warning Statement at top of page 27.

2. Control valve is defective

1. Locate and correct all leaks (see “Checking Gas Connections”, page 16).

2. Contact customer service.

Moisture/condensation noticed on windows.

1. Not enough combustion ventilation air.

1. Refer to Air for Combustion and Ventilation” requirements, page 8.

REPLACEMENT PARTS

NOTE: Use only original replacement parts. This will protect your warranty coverage for parts

replaced under warranty.

PARTS UNDER WARRANTY

Call Customer Service toll free at (1-866-573-0674) for referral information.

When calling Customer Service, have ready:

• Your name

• Your address

• Model and serial number of your heater

• How heater was malfunctioning

• Type of gas used (Propane/LP or Natural gas/NG)

• Purchase date

• Usually, we will ask you to return the defective part to the factory

PARTS NOT UNDER WARRANTY

Call Customer Service toll free at (1-866-573-0674) for referral information.

When calling Customer Service have ready:

• Model number of your heater

• The replacement part number

REPLACEMENT PARTS LIST

Part.. Description Part # QTY

1 Hood FHL008-02D 1 2 Louver FBB102 1 3 Door Assembly FBB104B 1 4 ODS NDD0308 - 400 1 5 Regulator RV83FI-4/9 1 6 Ignitor PIMSC1-01 1 7 HL041-01 Log 1 1 8 HL042-01 Log 2 1

9 HL043-01 Log 3 1 10 HL044-01 Log 4 1 11 HL045-01 Log 5 1 12 HL045-02 Log 6 1 13 Fuel Selection Device Assembly YDF06-FBD32RT 1 14 Fuel Selection Device Knob MDL304B 1 15 Receiver Box UN3 1 16 Remote Control CON 1001TH 1

PART AVAILABLE----NOT SHOWN

Hardware Package FBD400R001 1

For replacement parts, call our customer service department at

1-866-573-0674,

8:00 a.m - 4:30 p.m., EST, Monday - Friday or e-mail customerservice@usaprocom.com.

2-YEAR LIMITED WARRANTY The manufacturer warrants this product to be free from defects in workmanship and material present at time of shipment from the factory for two (2) years from the date of purchase. This warranty applies only to the original purchaser. The manufacturer agrees to correct such defect at no charge or, at our option, replace the product with a comparable or superior model.

To obtain warranty service, call our customer service department at 1-866-573-0674. You may be required to present a copy of your sales receipt as proof of purchase. All costs of removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the product by accident, misuse, improper installation, or by afxing accessories not produced by the manufacturer, are the purchaser’s responsibility. The manufacturer assumes no responsibility whatsoever for installation during the warranty period.

There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall not be liable for incidental, consequential, or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. This warranty gives you specic legal rights, and you also have other rights which vary from state to state. This warranty supersedes all prior warranties

This product may be covered by one or more of the following patents: (United States) 7013886, 7434447, 7607426, 7654820, (Europe) 07009672, 07024044, 08004868 or other U.S. and foreign patents pending.

Printed in China

Cedar Ridge RHFD400RT-M-M, CRHFD400RT-M-M User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual