Cecilware TS-4N User Manual
1/10 NITRO POWERED 4WD TOURING CAR
No.6167-F
JD6221
Thunder Tiger Corporation guarantees this model kit to be free from defects in both material and workmanship.
The total monetary value under warranty will in no case exceed the cost of the original kit purchased. This warranty
does not cover any components damaged by use or modification. Part or parts missing from this kit must be
reported within 60 days of purchase. No part or parts will be sent under warranty without proof of purchase.
To receive part or parts under warranty, the service center must receive a proof of purchase and/or the defective
part or parts. Should you find a defective or missing part, contact the authorized Thunder Tiger Service/Distributor
nearest you. Under no circumstances can a dealer or distributor accept return of a kit if assembly has started.
INTRODUCTION
Thank you for the purchase of this Thunder Tiger product. You should enjoy many hours of trouble free use
from this advanced R/C product. Thunder Tiger strives to bring you the highest level of quality and service we
can provide. We race and test our products around the world to bring you state-of-the-art items.
We offer on-line help 24-7 on our www.acehobby.com forum and our product specialists are ready to take your
call if you have any technical questions. Please read all instructions and familiarize yourself with the systems
and controls of this product before operating. Have fun and enjoy the exciting world of R/C.
ITEMS SUPPLIED
PURCHASED SEPARATELY
WITH ARTRMODELS
2-Channel, surface radio with 2 high torque servos
ITEMS REQUIRED
Glow Fuel, Methanol
10% to 20% Nitro
5% to 18% Caster / Synthetic Oil
Fuel Bottle
(300cc/600cc)
Glow Starter w/ Charger
HexWrench Set 4-Way Wrench
Alkaline Batteries
(12), AA-size
Philips Screw Drivers, Slotted Screw Driver,
Needle Nose Pliers.
5-Way Wrench
1
INSTALLING THE RADIO GEAR
skip if already assembled
1
a
c
f
b1
d
g
g
b2
e
h
i
a. Disassemble the roll bar.
b. Remove the 8 screws on the radio plate and two 3*10mm countersunk screws on the chassis.
c.
Install the steering / throttle servos onto the mounts with four tap screws. Notice the orientation of the
throttle / steering servo output shafts
d. Install 4 AAsize alkaline batteries in receiver battery box and connect the receiver battery box to the
receiver switch.
e. Install the battery box below the radio plate and the receiver above the radio plate. Then secure the
two on the radio plate with large zip tie.
f. Properly plug the connectors/wires into the receiver: steering servo connector/wire into channel 1 slot,
throttle servo connector/wire into channel 2 slot, and battery switch connector/wire into battery slot.
g. Install the receiver switch onto the radio plate with its original screws.
h. Thread the receiver antenna / wire through the antenna mount and the antenna tube. Press-fit the
tube onto the antenna mount.
I. Use a small zip tie to organize the excess wiring away from any high temperature or moving parts.
.
2
INSTALLING STEERING SERVO LINKAGE
skip if already assembled
2
3
c
a b
a. Install the steering linkage rod onto steering servo horn.
b. Plug the steering linkage rod into the hole on the steering servo saver arm.
c. Install the servo horn onto steering servo output shaft. (In neutral, servo horn should be pointing
straight up, the steering arm should be pointing straight forward.)
d. Reassemble the radio plate onto the car with its original screws.(8 on the plate and 2 on the chassis)
INSTALLING THROTTLE LINKAGE
To engine
a
a. Build the throttle/brake linkages as shown on the diagram.
b. Secure the brake cam lever onto brake cam with set screw.
c. Install the servo horn onto throttle sero output shaft.
carburetor
lever
To brake cam
b
c
skip if already assembled
c
d
d
4
CHARGING THE GLOW PLUG IGNITER
Thunder Tiger Optional Part #2165, 1300MAH Glow Starter w/220V Charger.
Thunder Tiger Optional Part #2166, 1300MAH Glow Starter w/110VCharger.
a b c
a. Plug the charger into an AC outlet, and then pull on the igniter lever to accept the charging adapter.
b. At this point, the small red LED indicator on the charger should light up indicating the charging sequence
is in progress.
c. When the charging complete, pull on the glow plug igniter lever to unplug the glow igniter.
Charge the new glow plug igniter for 16 to 24 hours on the first charge. For subsequent charges, charge
it about 12 hours before next use.
NOTE:
If the igniter gets warm or hot during the charge, unplug the igniter from charger immediately. A warm /
hot igniter means the igniter is overcharged. Overcharging can damage the internal battery in the igniter;
thus, shortening its life.
3
Loading...