Cecilware FW36Q Installation Manual

Food Warmer

Operator Manual

FW24M, FW24Q, FW36M, FW36Q, FW48M, FW48Q,

FW60M, FW60Q, FW72M, FW72Q

Grindmaster-Cecilware

4003 Collins Lane, Louisville, KY 40245 USA
Phone: [phone] Toll Free: 800.695.4500
Fax: [phone]
Web: gmcw.com Email: [e-mail]

Safety Information .....................................2

Unpacking...................................................3

Installation..................................................3

Cleaning......................................................4

Thank you for purchasing this quality Warmer. For your safety and the safety of others, read all warnings
and the operator’s manual before installing or using the product. Properly instruct all operators. Keep
training records. For future reference, record serial number here:

Table of Contents

©2016 Grindmaster-Cecilware

Printed in USA

0916 Form # CW-339-01

Part # 390-00086

Grindmaster-Cecilware provides the
industry’s BEST warranty. Visit gmcw.com
for warranty terms and conditions.

Model: FW24M

2 Cecilware

®

Food Warmer

Safety Information

Important Safety Information

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.

WARNING

• Do not deform power cord.

• Follow national and local electrical codes.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.

• Use only on a dedicated circuit load that is properly protected and capable of the rated load. Do not use
extension cords, as this could result in electrical shock, overheating, and fire.

• Risk of electrical shock. Disconnect power before servicing or cleaning unit. Contact Grindmaster-Cecilware
Technical Service for service assistance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agents, or similarly
qualified persons in order to avoid a hazard.

• Due to the heat a warmer may produce, it must be placed with at least 1 inch clearance from all surfaces
at side and rear.

FAILURE TO COMPLY TO THE ABOVE RISKS PERSONAL INJURY, SHOCK HAZARD, FIRE, OR DAMAGE TO
EQUIPMENT.

CAUTION

• Read and understand the operating instructions in this manual thoroughly. Only allow properly trained
persons to operate this machine.

• Stay alert at all times during operation.

• Operate with care. Surfaces will get very hot and may cause serious burns.

NOTICE

• Keep operating area clean.

For your safety and the safety of others, read all warnings and the operator’s manual before installing or using
the product.

DANGER: This term warns the user of imminent hazard that will result in serious injury or death.
WARNING: This term refers to a potential hazard or unsafe practice, which could result in serious injury or

death.

CAUTION: This term refers to a potential hazard or unsafe practice, which could result in minor or moderate

injury.

NOTICE: This term refers to information that needs special attention or must be fully understood.

Food Warmer Cecilware

®

3

Unpacking

Carefully lift unit out of shipping container, and inspect
immediately for shipping damage. Your Food Warmer
was shipped in a carton designed to give it maximum
protection. It was thoroughly inspected before leaving
the factory. File any claims for shipping damage or
irregularities directly with the carrier.

Installation

1. Install Quartz Elements

(Tandems & Special Food Warmers with Quartz
Elements Packed Separate)

Place food warmer on workbench or floor with
reflector side up. Remove two screws from access covers
at either end of each individual unit. Remove access
covers and wire guard. Push flag terminals, found on
end of lead wires, onto male tab terminals at either end
of element. Make sure the terminals are pushed on
securely; a loose connection will cause arcing. Locate
element in unit so that groove in porcelain end cap is
nested in notch of element bracket. Hold element in
place and replace one access cover, making sure that
vertical leg of access cover is between element holder
and reflector, secure with two screws. Take wire guard
and insert the two wire ends into the holes in the
mounted access cover. Take second access cover and
slide it over the two wire ends of wire guard and then
position the vertical leg between the element holder
and reflector. Secure with two screws. Your food
warmer is now ready to mount in desired location.

2. Mounting Food Warmer

To avoid burning or charring of supporting surfaces, do
not install closer than 10” above an all stainless surface
or 15” above any other surface. The screws provided in
the ends of all Food Warmers should be used to mount
the food warmer in all cases. These are the correct
length – whether you are using the hanging tabs or
accessory stands or brackets. These screw into weld nuts
in the ends of the food warmers, and sheet metal
screws should not be used.

Mounting tabs are furnished which can be used if you
hang the food warmer.

If you mount the food warmer directly under a shelf,
bend tabs 90° and screw through them into the shelf,
or provide studs welded to the underside of metal
shelves.

Do not punch or drill any other holes in the housing.
The two screws on each end are sufficient, even on long
lengths. Do not attempt to join single units end to end
in the field. Long lengths can be ordered from the
factory, assembled, wired and ready to install.

3. Electrical Connection

These commercial food warmers are intended to be
permanently connected to the source of supply. They
are rated 120, 208, or 240 volts. All supply connections
must be suitable for at least 75°C (167° F) and their size
based on the wattage of the unit must be in compliance
with the National Electrical code (Table 402-5) or the
local electrical code. A ground connection is provided
in the supply box and must be used.

Connect electrical supply wires to the leads in the supply
box using the porcelain wire connectors. Do not
substitute plastic connectors. Always connect at the
supply box furnished. This box can be turned end for
end by removing the two mounting screws inside. Do
not make any other holes in housing for conduit or BX.
Food warmers with supply box on side instead of end,
available on request. Food warmers shipped with
tubular type mounting assemblies will always have
supply boxes on side. See next instruction.

CAUTION: Do not install closer than one inch

from a wall.

Grindmaster-Cecilware

4003 Collins Lane, Louisville, KY 40245 USA
Phone: [phone] Toll Free: 800.695.4500
Fax: [phone]
Web: gmcw.com Email: [e-mail]

Grindmaster-Cecilware provides the
industry’s BEST warranty. Visit gmcw.com
for warranty terms and conditions.

©2016 Grindmaster-Cecilware

Printed in USA

0916 Form # CW-339-01

Part # 390-00086

Installation (continued) Cleaning

4. Convert to Side Supply

Remove cover plate from side of housing and supply
box from end of housing. Attach supply box on side of
housing and reroute pigtail lead wire to supply box.
Attach cover plate over opening on end of housing.

Stainless steel exterior surfaces can be cleaned with a
damp cloth.

If you need help, call Grindmaster-Cecilware Technical
Service Department, [phone] or [phone]
(USA & Canada only) (Monday through Friday 8 AM - 6
PM EST). Please have the model and serial number
ready so that accurate information can be given.

Prior authorization must be obtained from
Grindmaster- Cecilware for all warranty claims.

Grindmaster-Cecilware provides the industry’s
BEST warranty. Visit our website at GMCW.com
for warranty terms and conditions.

CAUTION: Disconnect power from warmer before

attempting electrical repairs.