Edition 09/2006 G0301FR0270V01
1
M OU N TING KIT
Qty Description
Photo
Funtion
1
M5x8 DIAX® screws
Keypad mounting screw
1
DIAX® spanner
Spanner
4
M4x30 screws
2 * keypad
2 * remote electronics
4
S5 plastic anchors
2 * keypad
2 * remote electronics
1
05D 680K varistor
For the lock
2 Wiring Sealed caps
Cable to the remote
controller
Keypad: 165 x 43 x 27 MM.
Remote Electronics: 147 x 124 x 55 MM.
OPERATING AND INSTALLATION INSTRUCTIONS
PROFIL 100 EC
Illuminated Mullion Stainless Steel Keypad
Remote Electronics
The PROFIL100EC keypad is available in 1, 2 or 3 relay output.
Refer to page 8 and 9 for the instructions of version 2 and 3 relay.
IP 64 DM
Edition 09/2006 G0301FR0270V01
2
I. PRODUCT INFORMATION
A. DESCRIPTION 1 relay output version
INPUT VOLTAGE 12 – 24 VAC FREE VOLTAGE
INPUT VOLTAGE 12 - 48 V D C F REE VOLTAGE
12-digit back-lit keypad keys
EPROM memory storage
100 Pin code programmables in 4 or 5-digit code
1 relay output N/O & N/C contact 8A/250V
1 programmable master code in 4 or 5-digit
Buzzer audible signal
1 request-to-exit input
P2 jumper: Reset mas ter code an d user codes
P3 jumper: modification of individual code by the user
B. DEFAULT VALUES
Illumination time: 10 seconds
Relay release time: 1 second
Code length: 5-digit
Master Code: 12345
Programming mode time: 120 sec
Sub master code for user to reprogram its Pin code (1 relay output version): *, #
C. AUDIBLE SIGNAL
The buzzer indicates different audi ble signals. It can be turned off by cutting the ST1 wire on the
remote controller (see page 6)
1 short beep Keypad powered
1 long beep data computing in programming or access granted
2 short beep s Ente r or Exit from programming
4 short beeps data computing error
D. CODE LENGTH
The master code and the User codes can be of 4 or 5-digit in length.
All t he keypad keys can be u sed to program a code.
The master code and the Pin code can be of 4 or 5-digit code.
The master code CAN NOT be used as a PIN code (User Pin code).
Codes 00000 and 0000 can only be used to delete a user Pin code. To delete a specific Use r
pin Code replace it by 0000 if code length is 4-digit format or replace it by 00000 if the code
is in 5-digit format.
E. REQUEST-TO-EXIT INPUT
This normally open loop that operates upon activation relay 1 (GALEO, GALEO 2 or GALEO 3) or
relay 2 (GALEO 2 or 3 version). This feature is especially useful when controlling a lock.
P1 input activates relay 1.
P2 input activates relay 2.
(The output can be programmed).
The timer input H if connected allows using the 0 key as a request-to-enter. If the timer
contact i s op en then the 0 digit key is us ed for the Pin code and if th e contact is clo se d then
the 0 key is used fo r the request-t o- enter.
F. CONSUMPTION
12VAC: 20mA in stand by, 100mA max all 3 relays activated
24V AC:
10mA in stand by, 50mA max all 3 relays activated
(Lock consumption not included)
Edition 09/2006 G0301FR0270V01
3
WIRING DIAGRAM PROFIL100EC 1 RELAY OUTPUT
V : Varistors
Terminal Description
V Input voltage 12/24 VAC or 12/48 VDC
V Input voltage 12/24 VAC or 12/48 VDC
R1 Contact repos du relais 1
C1 Commun du relais 1
T1 Contact travail du relais 1
P1 Request-to-exit input relay 1
M Common of in put
PX Yellow wire request-to-enter Bell button
H Timer Contact
+ White wire keypad
- Brown wire keypad
E Green wire (illumination)
This device comes with a varistor.
The vari stor mus t be connected on the strik e terminal (elec t romag ne t…) opera ted
by the device.
If this pr oduct opera tes more than one s trike, each lock should have a varis tor.
The varistor controls the overload produced by the strike coil – back emf.
It is recommended to use a separate power supply when using a Shear Lock
Magnet.
Green
Distance 10
meters
maximum
P1
230V
V
Strike fail secure
Input volt ag e
according to lock
s
p
ecification
2
White
230V
2
P2: Place ju mper for reset
P3: Individual Code
modification by user
4
V
Ma
g
net
/
Strike
Fail
safe
V V R1 C1 T1 R2 C2 T2 R3 C3 T3 P1 M P2 Px H H + - E
RL1
P3 P2
ST1
Input volt ag e
12 to 24 V AC
or
12 to 48
VDC
Brown
Yellow
Loading...