CDA CI330, CI830, CI930, CI230 User Manual

washing machine

contents

WARNINGS

SPECIFICATIONS

INSTALLATION AND ASSEMBLY

USING THE APPLIANCE. PRACTICAL TIPS

MAINTENANCE AND CLEANING

SAFETY AND TROUBLESHOOTING

ENVIRONMENTAL WARNINGS

warnings

To avoid the risk of fire, electric shocks, injury or damage when using your washing machine, please take the following precautions:

This washing machine comes with a manual that includes operating, maintenance and installation instructions. Please read all the instructions before using the washing machine.

Do not wash items that have previously been cleaned, washed, soaked or treated with petrol, solvents for dry cleaning, other inflammable substances or explosives, as they produce fumes that could catch fire or explode.

Do not add petrol, solvents for dry cleaning or other inflammable or explosive substances to the wash water as they produce fumes that could catch fire or explode.

Do not repair or replace any part of the washing machine or try to carry out any type of servicing unless it is recommended in the maintenance instructions in the manual.

Do not climb onto the machine or stand

on the open hatch door.

Do not use an extension lead or adaptor to connect your washing machine to the mains supply.

The machine should only be used for the purpose it is designed for.

Follow the washing instructions recommended by the manufacturer of the garment to be washed.

Do not turn your washing machine on until you are sure that:

• It has been installed in accordance with the installation instructions.

• All the water, drainage, mains electricity and earth connections meet the local regulations and/or other applicable regulations.

washing machine

Drain hose

Hatch

Adjustable feet

specifications

Power

cord

Control

panel

Detergent dispenser

Stainless

steel drum

Accessible filter

ACCESSORIES

Water inlet hose.

washing machine

UNPACKING AND

UNBLOCKING THE WASHING MACHINE

a Remove the base, corner protectors and

top cover.

a Remove the screws holding the plastic

covers to the back of the washing machine.

b Loosen and remove the 3 blocking

screws.

installation and assembly

UNPACKING

UNBLOCKING

c Cover the holes with the plastic covers

you have just removed.

Do not throw the blocking screws away. You may need to move the washing machine at a later date.

Important

CONNECTION TO THE MAINS WATER SUPPLY AND

DRAINAGE

installation and assembly

CONNECTION TO THE

MAINS WATER SUPPLY

The water supply hose is inside the drum:

a Connect the bent end of the hose to the

threaded inlet of the electrovalve located at the rear of the washing machine.

b Connect the other end of the hose to

the water intake. Then securely tighten the connection nut.

It is important that the drain hose bend is correctly fastened to the outlet, to prevent any risk of it becoming detached and causing flooding.

If your washing machine has a hot water intake, connect the hose with the red threaded end to the hot water tap, and to the electrovalve with the red filter.

The washing machine must be connected to the mains water supply,

Important

using the new supply hoses supplied with the appliance. Do not use water supply hoses that have been used before.

For your washing machine to work properly, the mains water pressure must be between 0.05 and 1MPa (0.05 and 10 Kgr/cm

DRAINAGE

CONNECTION

a It is recommended that you have a fixed

drainage outlet 50 to 70 cm from the floor. Avoid the drain hose being too tight, kinked or restricted.

LEVELLING THE WASHING MACHINE AND CONNECTING

IT TO THE MAINS ELECTRICITY SUPPLY

installation and assembly

LEVELLING

Use the adjustable feet to level the washing machine. This will reduce the noise level and prevent it from moving during use.

Do not bring the feet too far out, you will achieve better stability.

Important

You need to use a spanner for the models that have a nut.

ELECTRICAL CONNECTION

Consult the specifications plate located on the hatch door of the washing machine before making the electrical connections. Ensure that the voltage reaching the plug is the same as that on the plate.

Do not remove the specifications plate. The information on it is important.

It is very important to correctly earth the washing machine. The electrical installation, plug, socket, fuses or automatic switch and counter must be correctly dimensioned for the maximum power indicated on the specifications plate.

Important

Do not plug the washing machine plug into the socket with wet or damp hands.

To remove the power cord, pull on the body of the plug.

If the power cord is damaged, it must be replaced by a cord or special unit provided by either the manufacturer or your aftersales service.

With built-in washing machines, the plug must be accessible after installation.

PRE-CLEANING

When your washing machine has been correctly installed, we recommend that you pre-clean the machine.

This is to check that the installation, the connections and the drainage are all correct, and to thoroughly clean the inside of the washing machine before any wash programmes are run (see the operating instructions on the following pages).

a Select the normal programme at 60ºC.

b Press the Start/Stop button.

+ 19 hidden pages