Page 1
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
CI260 freestanding washing
machine
Manual for Installation, Use and Maintenance
Page 2
2
Page 3
3
Contents page
page 4 Important
page 6 Safety warnings
page 7 Warning
page 8 Recommendations
page 9 Before first use
Page 11 Detergents and additives
Page 12 Eco note
Loading the washing machine
Page 13 Control panel
Page 14 Starting a wash programme
Page 18 Wash programme phases and power cuts
Page 19 Programme table
Page 22 Care and maintenance
Page 23 Pump filter
Page 24 Detergent drawer
Page 25 Cleaning the washing machine exterior
The drum
Limescale removal
Page 26 Practical information
Page 28 Installation
Page 29 Levelling
Page 30 Connecting to the mains water supply
Drainage connection
Page 31 Electrical information
Page 32 Technical specifications
Page 33 Failure codes and troubleshooting
Troubleshooting
Page 36 International washing signs
Page 4
4
Important
This appliance must only be used for the purpose for which it is
intended, i.e. domestic use. Any other use could be dangerous and
may lead to premature failure of the appliance.
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note that
CDA reserve the right to invalidate the guarantee supplied with this
product following incorrect installation or misuse of the appliance.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity:
This appliance has been designed, constructed and marketed in
compliance with safety requirements of EEC Directive 2006/95/EEC
(Low voltage) and requirements of EMC Directive 2004/108/EEC.
Page 5
5
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority dierentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving from
inappropriate disposal and enables the constituent materials to be
recovered to obtain significant savings in energy and resources. As a
reminder of the need to dispose of household appliances separately,
the product is marked with a crossed-out wheeled dustbin.
Page 6
6
Safety warnings
• If the plug or cord are damaged, do not connect the appliance
to the mains power supply. If the cord is damaged it should be
replaced by the manufacturer or appointed service agent in order to
avoid a hazard.
• To remove the plug from the socket, pull on the body of the plug,
not the cable.
• Do not plug the appliance in to the mains power supply with wet or
damp hands.
• Never touch the appliance with wet hands or feet.
• Never open the detergent drawer when a programme is running.
• Never force the appliance door open when a programme is running.
• Since the appliance can reach high temperatures while running, do
not touch the drain hose or drained water during draining.
• In case of any failure, first unplug the appliance and close the
water tap.
• Repair on this appliance should only be undertaken by suitably
qualified personnel.
• Keep the packing materials away from children to prevent risk
of injury.
• Do not let children play with the washing machine.
• Keep pets away from the appliance.
• The appliance should not be installed on carpeted surfaces as this
can block the air ventilation on the base.
Page 7
7
Warnings
To avoid the risk of fire, electric shocks, injury or damage when using
your washing machine, please take the following precautions:
• Please read all the instructions before using the washing machine.
• Do not wash items that have previously been cleaned, washed,
soaked or treated with petrol, solvents for dry cleaning, other
inflammable substances or explosives, as they produce fumes that
could catch fire or explode.
• Do not add petrol, solvents for dry cleaning or other inflammable or
explosive substances to the wash water as they produce fumes that
could catch fire or explode.
• Do not repair or replace any part of the washing machine or try to
carry out any type of servicing unless it is recommended in
the maintenance instructions in the manual.
• Do not climb onto the machine or stand on the open porthole door.
• Do not use an extension lead or adaptor to connect your washing
machine to the mains supply.
• Follow the washing instructions recommended by the manufacturer
of the garment to be washed.
• Do not turn your washing machine on until you are sure that:
It has been installed in accordance with the installation instructions.
All the water, drainage, mains electricity and earth connections
meet the local regulations and/or other applicable
regulations.
Important: Ensure that the transit bolts have been removed prior
to using the machine.
Page 8
8
Recommendations
• Residues of detergent or softener left in the detergent drawer for
long periods will dry and stick to the detergent drawer. To prevent
this put the detergent and softener into the detergent drawer just
before washing.
• It is recommended that the pre-wash programme should only be
used for very dirty clothes.
• Do not exceed the maximum loading capacity.
• When the machine is not in use, keep the water tap closed.
• The appliance is not intended for use by people (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
• If the appliance is not to be used for prolonged periods of time,
unplug the appliance, close the water tap and leave the door ajar
to keep the inside of the machine dry and to prevent unpleasant
odours from developing.
• As a result of the quality control procedures during production, a
certain amount of water may remain in the appliance. This is normal
and does not signify a fault.
• Do not remove the rating plate. The information on it is important.
• This appliance should not be installed in locations where the
ambient temperature may fall below 0°C. Use in ambient
temperatures below 0°C may damage the machine.
Page 9
9
Before first use
When your washing machine has been correctly installed, we
recommend that you pre-clean the machine.
This is to check that the installation, the connections and the drainage
are all correct, and to thoroughly clean the inside of the washing
machine before any wash programmes are run.
Prior to pre-cleaning you should ensure the transit bolts have been
removed.
• Select the Cotton 95ºC programme and add a normal dose of
detergent into the detergent dispenser.
• Press the Start/Pause button.
Preparing Garments for Washing
• Wash lightly soiled garments using a short programme.
• Use a programme without prewash for medium-soiled garments.
• Wash heavily soiled garments using a long programme with
prewash.
• Wash white and coloured loads separately.
• We recommend that small garments are placed in a wash bag.
• We recommend using the delicate programmes for sensitive fabrics
• Separate clothes according to their types (cotton, synthetic,
sensitive, woollen, etc.), required washing temperatures and level of
dirtiness.
• Since new coloured clothes may shed dye on the first wash, wash
them separately.
Page 10
10
• Remove any metal pieces found on the items to be washed, for
example curtain hooks.
• Fasten all zips and buttons.
• Turn garments, such as knitted fabrics, inside out.
• Before placing the clothes in the drum, make sure all the pockets
are empty. Any small objects may block the drain pump.
• We recommend loading the washing machine to its full capacity for
best water and energy eciency.
• Whenever possible, we recommend that you wash garments of
dierent sizes within the same wash programme. This improves
the washing action and also aids the correct distribution of the
garments in the drum when spin-drying, and the washing machine
will therefore be quieter.
Page 11
11
Detergents and
additives
Your washing machine’s detergent
dispenser has three sections as shown
in figure 1.
Add the required amount of detergent
and fabric softener into the specific
sections of the detergent dispenser
before starting the wash programme.
The detergent dispenser is designed to
allow the use of liquid detergents rather
than adding them to the drum. You
should ensure that you insert the liquid
detergent level plate supplied in the
detergent section before adding the
liquid detergent.
To use powder detergents again, then
lift the blue tab back up and relocate it
by pushing it back into the dispenser
housing.
For washloads that require pre-washing,
add ¼ of the required detergent into
the prewash section, and the remainder
to the detergent section.
fig. 1
1 2 3
1 Detergent
2 Fabric softener
3 Prewash detergent
Page 12
12
Do not exceed the MAX level in the fabric softener section and
ensure that concentrated fabric softeners are diluted before use for
best washing results.
Remember that the amount of detergent to be used will always
depend on:
• The amount of clothes to be washed.
• How heavily the clothes are soiled.
• The hardness of the water (Information on water hardness in your
area can be obtained from your local water board).
We recommend the use of a decalcifying product if the water
hardness is high in your area.
Eco Note
The use of more detergent than necessary will not improve your
washing results, and will have a negative eect on the preservation of
the environment.
We therefore recommend you follow the detergent manufacturer’s
instructions.
Loading the washing machine
- Open the door.
- Add the items to be washed separately, ensuring they are loaded
evenly.
- When closing the door, ensure that no item is trapped between the
door and the door seal.
- Close the door securely, otherwise the programme will not start.
Page 13
13
Control panel
fig. 2
1. Mode button
2. Display
3. Mode selection button
4. Wash progress indicators
5. Start/pause button
6. Programme control knob
7. Spin speed control knob
8. Extra function buttons
400
CI260
500
600
700
800
1000
1200
0
A
mode ˚C select
B
C
D
E
F
G
H
I
J
K
L
0
hold
extra
pre
easy
60˚C
40˚C
1 2 3 4 5
6 7
8
Page 14
14
Starting a wash programme
• Turn the programme control knob to the required programme
• Turn the spin speed control knob to the required spin speed
• Select any required extra functions, as detailed below
• Select any required extra options, as detailed below
• Press the Start/Pause button
When a wash programme is in progress, the programme can
be paused by pressing the Start/Pause button at any time. The
programme will pause and the Start/Pause button light and progress
indicator will flash. To restart the programme, press the Start/Pause
button again.
For added safety, the porthole door does not open immediately at
the end of programme. There is a time delay of approximately two
minutes before you can open the door.
Programme selection
To select a programme, turn the programme control knob to the
required programme, as detailed in the programme table below
and also on the detergent dispenser. The display will show the
programme time, and the progress indicator will flash for the first
section of the programme.
Spin speed selection
Each selected programme has its own preset spin speed, as shown in
the programme table below.
You can reduce the spin speed or switch it o completely if required
by turning the spin speed control knob.
Page 15
15
A programme without final spin is used to prevent creasing when
washing special fabrics.
Extra functions
Extra functions can be selected once the programme has been set.
To select any extra function, press the required extra function button.
The programme table on page 19 shows the functions available for
each programme. If the function is available, the extra function button
indicator will illuminate. If it is not available, the indicator will flash
before switching o. The programme time shown on the display will
reduce or increase, according to the extra functions selected.
Prewash
This function adds a prewash to every programme. When this
function is selected, detergent must be added to the prewash section
of the detergent dispenser.
Rinse hold
This function pauses the programme before the final rinse water is
set to drain. This holds the clothes in water to prevent creasing. The
indicator will flash when the rinse hold function is in progress. To start
the final spin cycle, press the rinse hold button. The indicator will
switch o and the final spin programme will start.
Extra rinse
This function adds another rinse cycle to the programme, which is
ideal for large loads and garments belonging to people with sensitive
skin. Please note: this function will increase the water consumption.
Page 16
16
Easy iron
This function prevents garments from creasing excessively to make
them easier to iron.
Extra options
Extra options can be selected once the programme has been set.
The programme time shown on the display will reduce according to
the extra functions selected.
Wash temperature adjustment
The temperature for each programme can be adjusted if necessary.
The programme table on page 19 shows the temperature options
available for each programme.
To adjust the temperature:
• Press the mode button once. The display will show the preset
temperature.
• Press the select button repeatedly to cycle through the
temperatures available.
• Once the required temperature is shown on the display, the washing
machine will set after approximately three seconds’ delay.
Delay timer
A delay of up to 23 hours can be added to the start time in one hour
increments to allow the wash programme to finish at a convenient
time.
Page 17
17
To set the delay timer:
• Press the mode button twice. The display will show .
• Press the select button repeatedly to cycle through the delay times
available.
• Once the required time delay is shown on the display, the washing
machine will set after approximately three seconds’ delay.
Key Lock
The lock function ensures that the programme will not be aected if
any buttons are pressed accidentally.
The lock function should be activated after the wash programme has
been selected together with any extra functions.
To activate the key lock, press and hold
pre
and
hold
buttons together
for three seconds.
The display will show and the prewash, wash and rinse progress
indicators will flash to confirm the key lock is active.
When the key lock is active, the display will show and the
prewash, wash and rinse progress indicators will flash when any key is
pressed until the key lock is deactivated.
To deactivate the key lock, press and hold
pre
and
hold
buttons
together for three seconds.
The display will show and the spin/drain progress indicator will
flash to confirm the key lock is inactive.
Page 18
18
Wash programme phases
and power cuts
Programme Phases
• The progress indicators will illuminate successively as the
programme progresses. The time remaining until the end of the
programme will also appear on the display. It updates at regular
intervals, but not minute by minute.
Power Cuts
• If there is a power cut, when the electricity comes back on the
washing programme will continue to run from where it stopped.
Page 19
19
Wash temperature options
Preset (max)
spin speed
Pre Wash
Easy Iron
Rinse Hold
Extra Rinse
Index Programmes Cold 30 40 50 60 70 80 90 Speed
Max On
textile
A Cotton 95°C /
Antibacterial
A A A A A A A P 1200 A A A A
B Cotton 60°C
PW
A A A A P 1200 S A A A
C Eco 60°C A A A A P 1200 A A A A
D Cotton 40°C
AA
A A P 1200 A A A A
E Hygiene 30°C A P 1200 A A A
F Synthetics
60°C
A A A A P 800 A A A A
G Synthetics
40°C
A A P 800 A A A A
H Wool / Hand-
wash 40°C
A A P 600 A
I Delicate 30°C
/ Silk
A P 600 A
J Mix wash 30°C
/ Duvet 40°C
A P 800 A A A
K Fast 60' 60°C A A A A P 1200 A A
L Super Rapid 12' A P 800 A
Rinse & Spin P 1200 A A A
Spin P 1200 A
Drain P
P – preset A – available option function – function not available
Programme table
The table below shows the extra functions and temperatures available
for each wash programme.
Page 20
20
Index Programme Detergent
Compart.
Max. Dry
Load
Capacity (kg)
Type of Laundry Explanations
A Cotton 95°C 1 9 Dirty, high temperature
resistant cotton and linen
textiles. This programme
can also be run empty as a
cleaning cycle.
Underwear, sheets,
table cloths,
t-shirts, shirts,
towels (max 4kg)
B Cotton 60°C
prewash
1+3 9 Very dirty cotton and linen
textiles.
C Eco 60°C 1 9 Dirty coloured and linen
textiles.
D Cotton 40°C 1 9 Dirty coloured and linen
textiles.
E Hygiene
30°C
1 5 This programme can de-
stroy bacteria at 30°C, and
is suitable for slightly dirty
coloured linens and baby
clothing.
F Synthetics
60°C
1 3.5 Very dirty, synthetic or syn-
thetic mixed textiles.
Nylon socks,
blouse
G Synthetics
40°C
1 3.5 Dirty, synthetic or synthetic
mixed sensitive textiles.
H Wool / Hand-
wash 40°C
1 2.5 Less dirty, hand washable
cotton, wool, synthetic or
synthetic mixed clothing.
Hand wash to all
laundry
I Delicate /
Silk 30°C
1 2.5 Very light dirt, cold water,
hand and machine washable wool, silk mixed
clothing.
Silk mixture, shirt,
blouse, polyester,
poliamid, mixture
textile
J Duvet 40°C 1 This programme can wash duvets that are machine washable
(max 2.5kg)
Programme table
The table below shows the details of each wash programme.
Page 21
21
Index Programme Detergent
Compart.
Max. Dry
Load
Capacity (kg)
Type of Laundry Explanations
K Fast 60min
60°C
1 4 This programme will wash
dirty cottons, coloureds and
lined textiles in 60 minutes
at 60°C
Underwear, sheets,
table cloths,
t-shirts, shirts,
towels
L Super Rapid
12min 30°C
1 2 This programme will wash
lightly soiled items in 12
minutes at 30°C.
Please note: As the wash
time is short, the amount
of detergent used for this
programme should be
reduced from that required
for standard programmes.
If the washload is uneven,
the programme time will
increase. The door will
unlock two minutes after the
programme has finished.
For this programme, the
two minutes required for
the door safety lock is not
included in the programme
time.
Rinse & Spin The programme will run a rinse and spin cycle for any type of clothes.
Spin This programme will run a spin cycle for any type of clothes. This is not recom-
mended for delicates or woollens.
Drain This programme will run a drain cycle to remove the water inside the wash-
ing machine, for example if the programme has been interrupted before it is
complete.
Page 22
22
Care and maintenance
Before beginning any care or maintenance, you should always
disconnect the appliance from the electricity supply, and also turn
o the water supply.
If a programme has been run recently, wait for the water in the
appliance to cool down to prevent risk of scalding.
Water inlet lters
There are filters on the tap side of the
water inlet hose and at the ends of the
water inlet valves. These filters prevent
ingress of dirt or foreign objects into
the machine through the water supply.
These filters should be cleaned
approximately once a year to ensure
there is no interruption in the water
supply to the machine.
• Remove the water inlet hose.
• Remove the filters on the water inlet
valves using pliers.
• Remove the filters on the tap side of
the water inlet hose manually, as well
as the seal.
• Clean the filters thoroughly using a
brush.
• Replace the filters carefully, in the
same way as they were removed.
fig. 3
Page 23
23
fig. 4
Pump lter
The pump filter system prevents ingress of lint or foreign objects into
the drain pump, reducing the risk of damage.
The pump filter should be cleaned regularly, every two to three
months at least.
To clean the lter:
• Open the kickplate cover by pulling down on the groove at the top
of the cover.
• Place a container under the filter cover to collect the flow of the
remaining water from the machine.
• Loosen the filter cover by turning it slowly anti-clockwise until the
remaining water has drained away.
• When all the water has drained out of the machine, turn the filter
cover several times until the filter can be completely removed.
• Remove any objects caught in the filter and the drain pump.
• Refit the filter by turning it clockwise.
• Replace the kickplate cover.
Please note - failure to replace the filter cover properly will cause
water to leak from the machine.
To avoid injury, do not carry out this operation when the wash
water is at a temperature over 30ºC
Page 24
24
fig. 5
Detergent drawer
Detergents may cause residue build up
in the detergent drawer and the drawer
housing over time. The drawer should
be cleaned regularly to remove these
residues.
To remove the drawer:
• Pull the drawer out until it stops.
• To remove the drawer, press down on
the siphon lid inside the drawer and
remove from the housing, as shown
in figure 5.
• Lift the siphon lid upwards to remove
it, as shown in figure 6.
• Wash the drawer and siphon lid using
warm water and a brush, ensuring all
compartments are clean.
• Dry the drawer thoroughly and
replace the siphon lid properly.
• Remove the residues from the drawer
housing without letting them fall into
the machine.
• Replace the detergent drawer inside
the housing, reversing the steps
above.
Please note - A dirty or incorrectly fitted siphon will prevent the
detergents from being taken in, and leave water inside the detergent
drawer compartments at the end of wash.
fig. 6
Siphon plug
Page 25
25
Cleaning the washing machine exterior
The exterior of the washing machine should be cleaned with warm
soapy water or a gentle cleaning agent. Do not use abrasive cleaning
products or solvents.
It should then be dried thoroughly with a soft cloth.
Please note - wipe any detergent spills immediately to minimise the
risk of damage to the washing machine exterior.
The drum
Do not leave metal objects such as coins inside the drum, as these
can cause the formation of rust stains.
To remove rust stains, use a chlorine free cleaner and follow the
manufacturer’s warnings for the cleaner.
Never use abrasive products, such as scourers, to remove rust stains.
Limescale removal
If proprietary limescale removers are required, follow the
manufacturer’s warnings for the limescale remover.
Please note - Limescale removers contain acids which may aect the
colour in clothes, as well as damaging the appliance.
Page 26
26
Practical information
Alcoholic beverages: The stain, should first be washed with cold
water, than wiped with glycerine and water and be rinsed with water
mixed with vinegar.
Shoe Polish: The stain should be slightly scratched without
ruining the cloth, rubbed with detergent and rinsed. In case it is not
eliminated, it should be rubbed with 1 unit of pure alcohol (96 degrees)
mixed in 2 units of water and then washed with lukewarm water.
Tea and coee: Stretch the stained area of your cloth on the top of a
container and pour water as hot as the type of cloth can endure. If the
type of cloth is suitable, wash it with lye.
Chocolate and cocoa: By leaving your clothes in cold water and
rubbing with soap or detergent, wash it in the highest temperature
that the type of cloth can endure. If there is still a stain left, wipe with
oxygenated water (in proportion of 3%).
Tomato paste: After scraping the dried pieces without ruining the
cloth, leave in cold water for about 30 minutes and wash by rubbing
with detergent.
Meat/soup/egg: Eliminate the dried stain residues and wipe with a
sponge or soft cloth dampened with cold water. Rub with detergent
and wash with diluted lye.
Grease and oil stains: First wipe the residues. Rub the stain with
detergent and then wash with lukewarm soapy water.
Mustard: First apply glycerine to the stained area. Rub with detergent
and then wash. If the stain still does not disappear, wipe with alcohol
(On synthetic and coloured cloth, a mixture of 1 unit alcohol, 2 units
water should be used)
Page 27
27
Practical information
Blood stain: Lay your clothes in cold water for 30 minutes. If the stain
still does not disappear, lay in mixture of water and ammonia (3
table-spoons of ammonia in 4 litres of water) for 30 minutes.
Cream, ice-cream and milk: Lay your clothes in cold water and rub
the stained area with detergent. If the stain has still not disappeared,
apply lye on the fabric of your clothes in proper proportion. (Do not
use lye on coloured clothes.)
Mould: Mould stains should be cleaned as soon as possible. The
stain should be washed with detergent, and if it does not disappear, it
should be wiped with oxygenated water (in proportion of 3%).
Ink: Hold the stained area under cold water and wait until the inky
water completely runs o. Then rub with water diluted with lemon
juice and detergent, wash after waiting for 5 minutes.
Fruit: Stretch the stained area of your clothes on the top of a
container and pour cold water on it. Do not pour hot water on the
stain. Wipe with cold water and apply glycerine. Wait for 1-2 hours and
rinse after wiping with a few drops of white vinegar.
Grass stain: Rub the stained part with detergent. If the type of fabric
is suitable for use of lye, wash it with lye. Rub your woollen clothes
with alcohol. (For colour, use a mixture of 1 unit pure alcohol and 2
units of water).
Oil Paint: The stain should be eliminated before it dries by applying
thinner on it. Then it should be rubbed with detergent and washed.
Burnt stain: If your cloth is suitable for use of lye, you can add lye
into your washing water. For woollens, a cloth damped in oxygenated
water should be covered on the stain and it should be ironed with a
dry cloth on it. It should be washed after rinsing well.
Page 28
28
Installation
Transit bolts, located at the rear of the
appliance, must be removed prior to
using the appliance to prevent damage.
• Loosen the transit bolts using a
suitable spanner by turning them anticlockwise and then remove them.
• Cover the holes with the plastic plugs
supplied.
Do not throw the transit bolts away.
If you need to move the washing
machine after installation you should
rst replace the transit bolts.
Do not install your machine on rugs or
similar surfaces.
For your machine to work silently and
without any vibration, it should be
installed on a flat, non-slippery and solid
surface.
Never put cartons, wooden blocks or
similar materials under the machine to
level the surface under the appliance
fig. 8
Page 29
29
Levelling
To reduce the noise level from the
washing machine and to prevent
unnecessary movement during use,
ensure the washing machine is level
using the adjustable feet.
First, fix and level the rear feet. When
they are properly fixed, secure the
metal locknut tightly against the
underside of the washing machine.
• Put the washing machine into its
required position.
• Then level the front feet in the same
way as the front feet.
Please note: Raising the washing
machine too high can aect the
stability of the appliance.
fig. 10
fig. 9
Page 30
30
Connecting to the mains water supply
• Fit the seal included in the hose packing at the end of the water
inlet hose on the tap side.
• Connect the water inlet hose to a 3”/4, geared water tap. Then
securely tighten the connecting nut by hand.
• After connections are completed, check for the non-leakage of the
connection joints by turning on your tap completely.
For your washing machine to work properly, the mains water
pressure must be between 0.05 and 1MPa (0.1 - 10 bar).
Drainage connection
• It is recommended that you have a
fixed drainage outlet 60 to 70 cm
from the floor.
• Avoid the drain hose being too tight,
kinked or restricted.
• The water outlet can either be
connected to a water drain or to
a sink outlet spigot. This connect
should be a minimum of 60cm and
a maximum of 100cm from the floor.
The drain hose should be no longer
than 4m in length to ensure good
performance from the washing
machine.
• After connecting the water supply,
check to ensure there are no leaks.
fig. 11
min
60 cm
Page 31
31
The drain hose must be securely fastened to the outlet to prevent
any risk of the drain hose becoming detached and causing
ooding.
Once the appliance is connected to the water supply and the drain
connection, ensure that the water inlet and drain hoses are not
folded, twisted, crushed or elongated by stretching when moving the
appliance into position.
Electrical information
Warning! This appliance must be earthed.
The mains lead of this appliance has been fitted with a BS 1363A 13 amp
fused plug. To change a fuse in this type of plug, follow the steps below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the
fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in position.
Page 32
32
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should be
cut o and disposed of safely to prevent the risk of electric shock. A
suitable alternative plug of at least 13 Amp rating to BS 1363 should
be used.
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:-
• The wire which is coloured GREEN and YELLOW must be connected
to the terminal which is marked with letter (E) or by the Earth
symbol or coloured GREEN and YELLOW.
• The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter (N), or coloured BLACK.
• The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter (L) or coloured RED.
If in doubt regarding the electrical connection of this appliance, consult a
qualified electrician. Do not shorten the supply cable, the appliance may
require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible place.
Technical specications
Maximum dry laundry capacity (kg) 9
Recommended loading (kg) 8,5
Height (cm) 85
Width (cm) 59,6
Depth (cm) 61
Page 33
33
Failure Probable failure The process to be done
The door is not shut
properly.
Shut the door properly so that you hear the
click.
If the error persists, unplug the machine, close
the water tap and contact CDA Customer Care.
Inadequate water
supply.
Make sure the water tap is fully open and there
is no fault with the water supply.
Clean the inlet filter as described on page 14.
Restart the washing machine.
If the error persists, unplug the machine, close
the water tap and contact CDA Customer Care.
The pump filter is
blocked or there is a
fault with the pump.
Clean the pump filter as described on page 15
If the error persists, unplug the machine, close
the water tap and contact CDA Customer Care.
The machine has
overfilled.
The machine will automatically perform a drain
cycle. Once the drain cycle is complete, unplug
the machine, close the water tap and contact
CDA Customer Care.
Drum motor failure. Unplug the machine, close the water tap and
contact CDA Customer Care.
Failure codes and troubleshooting
Your machine is equipped with diagnostic systems which monitor
wash progress and will intervene to protect the washing machine in
the event of a fault.
Troubleshooting
All repairing which must be done on the machine should be done by
authorized service. When a repairing is required for your machine or
you are unable to eliminate the failure with the help of the information
given below:
• Unplug the machine.
• Close the water tap.
• Contact CDA Customer Care.
Page 34
34
Fault Probable cause Methods of elimination
The machine will not
start.
It is unplugged. Insert the plug into the socket.
The fuse is damaged. Replace the fuse.
There is a fault with the power
supply.
Check the power supply.
Start/pause button has not been
pressed.
Press the start/pause button.
The programme knob is in O (o)
status.
Bring the programme knob on the desired
status.
The door is not shut properly. Shut the door properly.
Your machine does
not receive water.
Water tap is closed. Open water tap.
The water inlet hose may be
bent.
Check the water inlet hose.
The water inlet hose is
obstructed.
Clean the filters of water inlet hose. (*)
The valve inlet filter is obstructed. Clean the valve inlet filters. (*)
The door is not shut properly. Shut the door properly.
Your machine is not
draining water.
The drain hose is obstructed or
bent.
Check the drain hose.
The pump filter is obstructed. Clean the pump filter. (*)
The washing was not evenly
loaded.
Remove the washload and reload the
garments evenly
Your machine is
vibrating.
The transit bolts have not been
removed.
Adjust the feet. (**)
The washload is small. Remove the transit bolts (**)
There is a small amount of
clothes in the device.
This is not indicative of a fault.
The washing machine is
overloaded, or badly loaded.
Do not exceed the load capacity, and
ensure the clothes are loaded evenly.
The washing machine is leaning
on a solid object.
Ensure the machine is installed apart from
other objects.
(*)SeeCare and maintenance on page 22.
(**)See Installation on page 28.
Page 35
35
Fault Probable cause Methods of elimination
Excessive foam
in the detergent
drawer.
Too much detergent has been
used.
Press the Start/Pause button. In order to
stop the foam, dilute one tablespoon of
softener in half a litre of water and pour
it in the detergent drawer. Wait 5-10
minutes, then press the Start/Pause button.
Ensure correct detergent dosing for all
washes.
Wrong detergent has been used. Use only the detergents produced for full
automatic machines.
The washing result is
bad.
The incorrect programme was
selected.
Select a suitable programme (see the
Programme Table on page 19)
The amount of detergent used is
not correct.
Follow the recommendations from the
detergent manufacturer.
The washing machine is
overloaded, or badly loaded.
Do not exceed the load capacity, and
ensure the clothes are loaded evenly.
The water is drained
from the machine as
soon as it is filled.
The machine is siphoning. Raise the drain pipe outlet above the
minimum specified. (**)
No water is seen
in the drum during
washing.
This is not indicative of a fault.
The water is in the lower section
of the drum.
-
There are residues
of detergent on the
clothes.
This is not indicative of a fault.
This can be caused by low
temperature wash programmes
or excessive detergent use.
Reduce the amount of detergent, or use
liquid detergent. Alternatively, use the
extra rinse function.
There are grey stains
on the clothes.
This is not indicative of a fault.
This can be caused by low
temperature wash programmes
or insucient detergent use.
Increase the amount of detergent or the
programme temperature, ensuring the
washload is suitable for the temperature
selected.
The spinning
process is not done
or starts with delay.
The washload is out of balance. Do not exceed the load capacity, and
ensure the clothes are loaded evenly.
(**)See the section concerning installations your machine.
Page 36
36
International washing signs
Wash up to 90 °C Wash up to 60 °C Wash up to 30 °C Do not wash in a
washing machine
Washing
temparature
Do not wash in a
washing machine
Lukewarm iron Medium hot iron
Hot iron Do not iron Do not tumble
dry
Hang to dry
Drip dry Dry flat Do not bleach Handy to bleach
All of these are dry cleaning symbols. The letters are to instruct the
cleaner what type of solvent to be used.
Garments bearing these symbols should not be washed in your
machine unless the label says otherwise.
Page 37
37
Page 38
38
Page 39
39
Page 40
Please contact our Customer Care Department, or for Service on the details below.
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu
Loading...