CCT Lighting Z000N, Z000X, Z000A, Z000S, Z000T User Information

i:-======---- - - --------------.;;.....;;;.....;;..;=._.=:.;..::..,;=...,;=...,;=...,;=...,;=.-=-~-=--=--=--~-~--_ ---.::::. -_ -_ -_ -_ -_ -=========::::=::===============================:::i

FAULT FINDING

Cure Symptom Possible Fault

--+--------

No light No Lamp

Uneven Light Lamp Adjustment

MAINTENANCE

Open lamp chassis observing safety precautions .
rolloctor through the bottom of the lamphouse with the tube

removed using a slightly damp cloth to which a little detergent
h3Sbeenadded . ·
Lenses should be cleaned with a damp cloth only.
Periodic inspection should be carried out, of the lampholder und
cable. Any components showing wear or
replaced immediately. Contact your CCT representative for list
of spare parts available.

. CALJTION

Damaged lenses or UV safety screens MUST be replaced
befor_e luminaire is used .

(a) When replacing or adjusting a lamp, the product ,
particular attention to all internal and external wiring, should be
inspected and any faults corrected .
(b) At least once every twelve months the
should be bench inspected for electrical and m1:chanical wear

and damage . If not portable this inspection should be carried

out jn situ.

(c) Depending upon usage , internal and external wiring will
deteriorate in time and should be replaced al the first indication
of wear or aging.

(d) Product can be returned to any CCT service representative
for repair and or maintenance . Spare and replacement parts
can be supplied for use by other compentent service

Finally ...

CHECK CABLE AND PLUG FOR ANY SIGNS OF DAMAGE
REPLACE DAMAGED PARTS IMMEDIATELY.

CCT Theatre Lighting Limited, is constantly developing,

changing its product line. All descriptions and specifications

and
In this publlcallon present only general particulars and
form any part of any contract .

spocification without prior notification . 1

Faulty Lamp
No Power

Shutlers Fully in
Lamp chassis

nol seated

knob moved ·
Lamp not fully

sealed in holder

Relleclor

selling

Toe right is reserved to change the

Fil Lamp
Fil new lamp
Check supply and ·
spollighl cable

Extend shutlers
Remove and re-insert

Check lamp
adjustment

Check lamp in
lampholder.
observing salety
precautions

Check

Clean ~he

damage should be

with

product. if portable,

'

improving

sha.D not

ACCESSORIES
ZS039 Fast Fit Lamphouse accessory
ZS040 Fast Fil Lens tube accessory

i Fast Fit · X' Lens Tube accessory

ZS04

20016 Df:--ip-in Iris

Z0017N Bait In Iris/Blackout
20120 Rota Gobo Holder
Z0121 Standard Gobo Holder
Z0013 Extra Colour Filter Frame tor
Z0014 Extra Colour Fitter Frame for ZOOOQ/RfT/ Lens Tubes
Z0015
Z0083 Hook Clamp

Extra Colour Filter Frame tor ZOOOSN Lens Tubes

·

ZOwi-iiP Lens Tubes

zooas Safley Chain

Y0057 Spigot

For complete details of colour change accessories suitable tor
the SIihouette Range see colour change data sheet.

C:C:T dlighting

WINDSOR HOUSE, 26 WILLOW LANE, MITCHAM,

TELEX: 946648 FAX UK:

SURREY, CR4 4NA. UK. TEL: [phone]

081-648 5263 FAX INT: 441-648 5263

C:C:T jlightiing

USE.R INFORM/.\ 1-ION

Leallet ref : WO\U\O

Jan ·90

~O~m)(Q)(l)]@~~® ~@@M

[p)f@iro~® ~[p)@i~o@[n)~

Base Down Lamp 1000/1200W

Order Code ZOOAO /N/P/Q/X/S/TN

. 220/240V ONLY

WARNING - BEFORE U~E :-

(a) Read CCT Lighting User Information General leaflet.
(b) Read these ins1ructions.
(c) Inspect product tor damage upon removal from its carton .
(d) Ensure that external supply wiring and socket (if to be used)

property installed and protected .

Is

11-llS INFORMATION IS GIVEN IN THE B'=ST INTERESTS OF:

Safety, Hanc:ing, Installation, Use
solp by CCT lighting.
Instructions relevant to each product will be found In the carton in
which the product is supplied. They must be carefully read before
any attempt is made to use and/or install the product. The
lion sheet should be retained for further reference . Additional
copies are available on request.

UK, ins.allers and users are obliged under the "Health and

In the
Safety at Work Act" to ensure that they are acquainted with
information
precautions
CCT
law and to

standards.

J

s;ipplied with the product and are fully aware of any

t:1at need to be taken.

produc:s are designed to conform to the requirements of UK

tha requirements of relevant national and international

and Maintenance of products

ins1ruc-

SPECIAL NOTE
CCT products should not be modttied. Any modttlcatlon may
renderthe product unsafe andwill Invalidate any safety/approval
marks. CCT Theatre.
sibllity for any damage caused as a result of their

INSTALLATION
Installation of CCT products should be carried out only by

competent persons in accordance with instructions supplied
with the
suitably

LAMP FITTING
Suitable tamps
220/240V HJOOW T/11, T/19 or equivalent
Damaged

manufacturers

tuminairn and/or accessory . If in any doubt, consult a
qualttied person.

er thermally deformed lamps MUST NOT be used. Lamp

Uqhtlng Llmited, .will not accept any respon.

modttlcatlon .

- Base MUST be GX9.5

instruct10ns must be followed at all times .

/!''\, [w ARNING I /f\. -

Never attempt to Insert a lamp with the spotlight connected lo a

· dimmer circuit or lo mains. Before opening the spotllghl unplug
the power cable. Failure to observe this precaution :

MAY RESULT IN SEVERE BURNS.
Do not touch the lamp surface
provided with the new tamp when fitting it Into the lampholder.
When changing a

condenser

When supplied the lampholder Is set for uso

order to re-set for 1200 Watt lamp adjust

Remove screws and
spacers (a). Lift
lampholder (b). Re-frt
lampholder lixing screws

with spacers below

lampholder fixing slots (c).

Note that :lamptray slide is engraved with centre line. Always

ensure that centre of lamp filament lo

mark. If it does not, reset lampholder as instructed above.

LAMPHOUSE
The Silhouette ZOOAO base down lamp 1000/1200W lamphouse

lamphouse is part of a
ZOOFO 1 OOOW Axial tamp lamphouse
ZOODO 2500W Base Down Lamphouse

ZOOBO 2000W Base Down Lamphouse

TIit Angle 90° - 0 - 70°

Beam

recerrt!y failed tamp, allow time for the lamp and

lens lo cool before removing it from the spotlight.

- use the disposable glove or shield

with a 1 OOOW lamp

as follows .

1000W

Lampholder setting Lampholder setting

be used coincides with this

range which Includes :-

1200W .

FfTTING
(a) Select desirer! tube .
(b) Decide whether lens knob/s are to be above or below tube
when In use (except
(c) Attach tube to lamphouse with 4 off M5x20 Allen bolls and
key provided .
(d) Decide whether front colour frame/ accessory cassette Is lo
be arranged for lop or side entry.

Adjust as necessary with 4 off M5x8 screws holding cassette to
lens tube.
(e) Suspension Yoke should be attached

With ZOOON, ZOOOP and ZOOOX Tubes to the tamphouse .
With other tubes directly to the tube via support bracket.
Select for best balance . Note that Yoke has optional holes
for height selection .

The Z00017N Iris Blackout, when used, is located behind the
shutter set.

LENS

LENS TUBE

• X' tube)

TUBES

ZOOON dQ ZOOOP 30

31° -H· Zoom

19•

-d0° Zoom-r 15• -32° Zoom

,.

r--r-,00:i

I

~

I '

I •

L.--l

zooos 10

g• -2 f • Zoom

r·-,~··

I '•

I lr

L •• _J

ZOOOT 8

a• Non-Zoom

f.JlQ

I .

;

'--'

zooox 15-32

,,

"

..

:-

seleclion holes

-c....,,.~1- drop-in Iris or

~

--.. -

Gale lor
Gobo holder

"

..

CJOLJ

zoooo 15

13• -23° Zoom

"

[)clQ

zooov 5

5°Non-Zoom

FlrllNG PLUG
A suitable plug of al leastl15A(220/240V) rating should be fit1ed tc
the srotlight power cable, observing the connection colour code

as follows:

MOUNTING

LUMINAIRE
Maximum ar steady state 1so

FOCUS AND LAMP AJUSTMENT
With the exception of ZOOOT and ZOOOV the lens system allows
vc1riable zoom beam spread and should be used to set the required

boam size, before trimming with the shutters or the Iris.

(a) With shutters/iris fully open slacken lens knobs and slide adjust
to maximum acceptable beam size/hardness.

(With a new lamp, socket support trim
to centralise filament.

(b) By means

If a Gaba is being projected, lenses and shutters can be

(c)

trimmed for image size and definition.(see also d.)

(d) Trim lens and reflector settings for optimum performance• by

adjusting
when setting has been completed .

• Peaky or flat field, Minimum/maximum brightness, Sort/hard focu

D

------- ,

M1n1mum d-stanc! from lighted obiect

w,th 10- leris tworsl Ji1U;,honl

MAXIMUM SURFACE TEMPERATURE (Msn

of shutters/Iris adjust gate size as required .

contfol knobs. Ensure they are fully finger tightened

flea,, froo1

lEllS KNOBS

WARNING j

3-Sm

0

c ta 45°c

Tighten lens knobs.

screws should be adjusted