CCI Phantom User Manual

Page 1
Paintball Gun
User’s Manual
Component Concepts, Inc. The Phantom™ Paintball
Gun User’s Manual
The information in this manual is subject to change without notice and does not represent a commitment on the part of Component Concepts, Inc. CCI reserves the right to make improvements to products without incurring any obligation to incorporate such improvements in products previously sold.
This manual contains information protected by copyright. No part of this manual may be photocopied or reproduced in any form without prior written consent from Component Concepts, Inc.
Copyright© 1989-2002 by Component Concepts, Inc. All rights are reserved.
The PHANTOM™ is a registered trademark of Component Concepts, Inc.
Component Concepts, Inc., 530 South Springbrook Road, Newberg, OR 97132
Phone: (503) 554-8095 Fax: (503) 554-9370
The Phantom™ User’s Manual i
Page 2
Precautions
Safety-Your Responsibility...................................... 1
Description and Operation
Introduction ............................................................. 2
Specifications.......................................................... 3
The Gun Safety ....................................................... 3
CO
Installation ....................................................... 4
2
Puncture Adapter Removal………………………….. 4
Load and Fire Paintballs ......................................... 5
Velocity Adjustment ................................................ 6
Service and Maintenance
Field Stripping ......................................................... 7
Cup Seal and O-ring Replacement ......................... 8
General Maintenance.............................................. 8
Service Notes.......................................................... 10
Parts List ................................................................. 12
Exploded View ........................................................ 13
Accessories............................................................. 14
Warranty and Disclaimers
Warranty ................................................................. 15
Disclaimers ............................................................. 16
ii The Phantom™ User’s Manual
Page 3
2 The Phantom™ User’s Manual
Page 4
Description and Operation
CO2 Installation
Stock
Place 12 gram CO stock housing with cartridge onto puncture adapter. This action pierces cartridge and pressurizes gun.
cartridge in stock housing. Screw
2
Puncture Adapter Removal
4 The Phantom™ User’s Manual
Page 5
Description and Operation
Velocity adjustment
Temperature and altitude influences the performance of CO
.
2
6 The Phantom™ User’s Manual
Page 6
Service and Maintenance
Cup Seal and O-ring Replacement
An extra O-ring and cup seal has been supplied to help you
8 The Phantom™ User’s Manual
Page 7
Service and Maintenance
Service and Maintenance
Service Notes
If your fitting should leak the internal O-ring in the fitting needs to be replaced. De gas the marker. Remove the tube by push­ing in the collet and pulling the tube out. If you have a metal type tube you also need to remove the rear thumb screw. Pull and wiggle the collet back and forth to extract from fitting body. Replace the O-ring. (#9428)
Compression metal line assembly is the newest type vertical air connection and requires a 7/16 wrench for disassembly. The rubber sleeve is designed for positive seal with proper compression.
Service Notes
10 The Phantom™ User’s Manual
The Phantom™ User’s Manual
11
Page 8
Item # Part# Description 15 9115 Retainer
16 9103 Power Tube, Modified Short 17 9116 Power Tube Assembly, Modified 18 9062 Anti-Kink Hammer Assembly 19 9051 Main Spring 20 9052 Tuned Port Compensator 21 9045 Bolt (21A, 14)
12 The Phantom™ User’s Manual
Page 9
Service and Maintenance
Accessories
14 The Phantom™ User’s Manual
Page 10
Warranty and Disclaimers
Disclaimers
This limited warranty does not extend to any products not purchased from Component Concepts, Inc. (CCI) or an
16 The Phantom™ User’s Manual
Page 11
______________________
______________________
______________________
Component Concepts, Inc.
530 South Springbrook Road Newberg, OR 97132
PLACE
NECESSARY
POSTAGE
HERE
Loading...