CC and C Technologies WL8210 User Manual
IEEE 8
02.11ac/a/
b/g/n
WLAN 11ac USB Adapter,2T2R
USER’S GUIDE
VERSION 1.1
© All rights reserved.
All trade names are registered trademarks of respective manufacturers listed.
This manual may not be copied in any media or form without the written consent of original maker.
1. Introduction .........................................................……...... 1
2. Wireless LAN Basics ................................................……...... 3
3. IP ADDRESS ..........................................................………….. 4
4. Install Driver/Utility ...............................................………….. 5
4.1 Windows XP/7/8/8.1................................................... 5
5. Wireless Network Configuration ............................................ 7
5.1 Utility Icon .............................................................. 7
5.2 Client Mode (Default Setting)........................................ 7
5.3 Virtual WiFi ............................................................ 13
6. Technical Specifications ................................................... 14
7. Troubleshooting .............................................................. 16
8. Glossary ....................................................................... 17
Thank you for your purchase of the WLAN 11ac USB Adapter,2T2R.
Featuring wireless technology, this wireless networking solution has been
designed for both large and small businesse s, and it is scalable so that you
can easily add more users and new network features depending on your
business scale.
FEATURES
Support Microsoft XP(32bit/64bit) / 7(32bit/64bit) / 8 / 8.1(32bit/64bit)
Operating distance of up to 300 meters in free space.
866.7/433.3/300/270/240/180/120/90/60/54/48/36/30/24/22/18/12/11/6
/5.5/2/1 Mbps selectable Data Rate according to client adapter default
antennas.
64/128-bit WEP , WPA, WPA2, WPS
2.400GHz ~ 2.4835GHz unlicensed ISM Frequency Band. Modulation
Method. 5GHz UNII, Midband, ISM bands.
IEEE 802.11b : DSSS (Direct Sequence Spread Spectrum).
IEEE 802.11 ac/a/g/n : OFDM (Orthogonal Frequency Division
Multiplexing).
Easy operation and setting up.
SYSTEM REQUIREMENTS
Windows System : XP(32bit/64bit) / 7(32bit/64bit) / 8 / 8.1(32bit/64bit).PCs
must have a device driver installed. It allows you to communicate with
WLAN 11ac USB Client Adapter.
1
BEFORE YOU START
1. Confirm Box Contents
WLAN 11ac USB Client Adapter
Quick Start Guide
Driver CD
CONNECTING YOUR WLAN 11ac USB CLIENT ADAPTER TO PC
Quick Start Guide
Connect your WLAN 11ac USB Client Adapter to your PC. Install driver.
GETTING TO KNOW WIRELESS LAN ADAPTER
LED Status
Quick Blinking – Adapter connects to Access Point.
Steady Blinking – WLAN 11ac USB
Adapter,2T2R is active.
Off – WLAN 11ac USB Adapter,2T2R is disabled.
Best Performance Requirement
2T2R ac Adapter
USB 3.0
Windows 7 or above
Wireless utility installed
Wireless 802.11ac AC1750 AP/Router with gigabit Ethernet port
2
Wireless LAN network defined by IEEE 802.11ac/a/b/g standard committee
Could be configured as:
Ad Hoc wireless LAN.
Infrastructure wireless LAN.
Ad Hoc network is a group of PCs installed with wireless LAN cards; this group
of PCs is called a BSS (Basic Service Set). PCs in this group can use their
wireless LAN cards to communicate with each other, but can not connect to the
Internet.
Ad Hoc Wireless Network Infrastructure Wireless Network
The most obvious difference between Infrastructure wireless network and Ad
Hoc wireless network is that the PCs in Infrastructure wireless network can
access the resource in the Internet through Access Point.
Depending on your requirement, you can easily set up your PC’s network to be
a “Ad Hoc” or “Infrastructure” wireless network. Generally speaking, if in your
network, there is an Access Point in it, we recommend you to set your
network as an “Infrastructure”, so it can connect to the Internet.
3
To use the WLAN 11ac USB Client Adapter with a computing device, the
WLAN 11ac USB Adapter,2T2R must be equipped with a proper Interface. All
drivers and supporting software for the WLAN 11ac USB Adapter,2T2R must
be installed and configured first.
Ask your system administrator for the following information, which
you may need to provide during driver installation :
Your Wireless Client Name.
Your Wireless SSID.
Your computer’s unique client name and workgroup name. For your
network account, your user name and password.
Your IP address, gateway address, and subnet mask if you’re not
using a DHCP client.
Any computer on a network is identified by a unique network address. There
are two methods to assign a network address to a computer on a TCP/IP
network :
Static IP addressing.
Dynamic IP addressing (DHCP Client).
In network with static IP addressing, the network administrator manually
assigns an IP address to each computer. Once a static IP address is assigned,
a computer uses the same IP address every time it reboots and logs on to the
network. You may manually change the IP address in the
dialog box.
require additional network management software
Network using static IP address is easy to set up and do not
.
Network Properties
In network with dynamic IP addressing, a DHCP server in the network
dynamically assigns IP addresses to all clients every time they log on to the
network. Network using dynamic IP address requires setting up and running a
DHCP Server.
4
The installation & driver CD will automatically activate the autorun installation
program after you insert the disk into your CD drive.
Step 1 : (Win7/8 only)
Insert the installation CD into your CDROM. Win7/8 UAC Dialog is shown.
Click Yes to continue.
Step 2 :
Preparing Setup dialog is shown
Step 3 :
Wizard is ready to install driver and
utility. Click Next to begin the
installation
Installing & configuring WLAN driver
and utility
5
Installing Cisco 802.1x module
Step 4 :
Click Finish to complete installation.
The installation will affect after
windows rebooting
6
Loading...