CC and C Technologies WL7200V2 User Manual

IEEE

802.11

b/g/n

11n Wi-Fi USB Dongle

USER’S GUIDE

All trade names are registered trademarks of respective manufacturers listed.

This manual may not be copied in any media or form without the written consent of original maker.

VERSION 1.2

© All rights reserved.

1. Introduction .........................................................……..1

2. Wireless LAN Basics ................................................……..3

3. IP ADDRESS ..........................................................……..4

4. Install Driver/Utility ...............................................……..5

5. Wireless Network Configuration .......................................7

5.1 Utility Icon .........................................................7

5.2 Client Mode (Default Setting) ...................................7

6. Technical Specifications ................................................ 14

7. Troubleshooting ..........................................................16

8. Glossary ................................................................... .17

1

Thank you for your purchase of the WLAN Adapter. Featuring wireless
technology, this wireless networking solution has been designed for both
large and small businesses, and it is scalable so that you can easily add
more users and new network features depending on your business scale.

FEATURES

Support Microsoft XP(32bit/64bit) / Vista(32bit/64bit) / Win7(32bit/64bit) /
Win8(32bit/64bit).

Operating distance of up to 300 meters in free space.
150/120/90/60/54/48/36/30/24/22/18/12/11/6/5.5/2/1 Mbps selectable Data

Rate.
64/128-bit WEP , WPA (Wi-Fi Protected Access), WPA2

2.400GHz ~ 2.4835GHz unlicensed ISM Frequency Band.

Modulation Method :
IEEE 802.11b : DSSS (Direct Sequence Spread Spectrum).
IEEE 802.11g / 802.11n : OFDM (Orthogonal Frequency Division

Multiplexing). Easy operation and setting up.

SYSTEM REQUIREMENTS

Windows System : XP(32bit/64bit) / Vista(32bit/64bit) / Win7(32bit/64bit) /

Win8(32bit/64bit).

System must have a device driver installed. It allows you to
communicate with WLAN 11n USB Client Adapter.

2

BEFORE YOU START

1. Confirm Box Contents

◆

WLAN 11n USB Client Adapter

◆ Quick Start Guide

◆

Driver CD

CONNECTING YOUR WLAN 11n USB Client Adapter

Quick Start Guide

Connect your WLAN 11n USB Client Adapter. Install driver.

GETTING TO KNOW WIRELESS LAN ADAPTER

LED

LED turns on when WLAN link to WLAN adaptor or AP.

LED is blinking when WLAN Adapter is active.

3

Wireless LAN network defined by IEEE 802.11b/g standard committee
could be configured as :

Ad Hoc wireless LAN.

Infrastructure wireless LAN.

Ad Hoc network is a group of wireless LAN cards, this

group is called a BSS (Basic Service Set). This group can use their wireless
LAN cards to communicate with each other, but can not
connect to the Internet.

Ad Hoc Wireless Network Infrastructure Wireless Network

The most obvious difference between Infrastructure wireless network
and Ad Hoc wireless network in Infrastructure wireless network can
access the resource in the Internet through Access Point.

Depending on your requirement, you can easily set up your system

network to be a “Ad Hoc” or “Infrastructure” wireless network. Generally
speaking, if in your network, there is an Access Point in it, we recommend
you to set your network as an “Infrastructure”, so it can connect to
the Internet.

4

To use the WLAN 11n USB Client Adapter with a computing device, the WLAN
Adapter must be equipped with a proper Interface. All drivers and supporting
software for the WLAN Adapter must be installed and configured first.

Ask your system administrator for the following information, which
you may need to provide during driver installation :

Your Wireless Client
Name. Your Wireless
SSID.
Your personal computer’s unique client name and
workgroup name. For your network account, your user
name and password.

Your IP address, gateway address, and subnet mask if you’re

not using a DHCP client.

Any personal computer on a network is identified by a unique
network address. There are two methods to assign a network
address to a personal computer on a TCP/IP network :

Static IP addressing.
Dynamic IP addressing (DHCP Client).

In network with static IP addressing, the network administrator
manually assigns an IP address to each personal computer. Once a
static IP address is assigned, a personal computer uses the same IP
address every time it reboots and logs on to the network. You may
manually change the IP address in the

Network Properties dialog box.

Network using static IP address is

easy to set up and do not require additional network management
software.

In network with dynamic IP addressing, a DHCP server in the
network dynamically assigns IP addresses to all clients every time
they log on to the network. Network using dynamic IP address
requires setting up and running a DHCP Server.

5

The installation & driver CD will automatically activate the autorun installation
program after you insert the disk into your CD drive.

Step 1 :

Insert the installation CD into your
CD-ROM. Choose the Setup
Language and click Next button.

Step 2 :

Installation descriptions
shown. Click Next to
continue.

Click Install to begin the installation

6

Installing & configuring WLAN utility

Installing Drivers.

Step 3 :

Click Finish to complete installation