CC and C Technologies BT500 Users Manual

晶訊科技股份有限公司

CC&C Technologies, Inc.

User's Manual

BT5.0 Dongle

BT-500

Manufacturer : Kunshan CC&C Technologies, Co., LTD.

晶訊科技股份有限公司

Data

CC&C Technologies, Inc.

Bluetooth 5 Dongle

Description

BT-500 is a Bluetooth 5 Low Energy class 1

dongle that provides a complete solution

from various interfaces to different sensors

to BLE protocol stack and applica-tions. It

includes 32MHz crystal and a sys-tem-on-

chip Nordic nRF52840. The mini-mal parts

count and small footprint of the BT-500 is

ideally suited for the re-quirement of high

integration Bluetooth Low Energy

technology in portable devices and

consumer electronics.

The system-on-chip architecture design of

the module makes a much smaller space

and minimal cost and simplifies the whole

system design.

Sheet

1Mbs, 500 kbs, 125 kbs

 Bluetooth 5 support for long range and

high throughput

 AES 128-bit ECB/CCM/AAR hardware

accelerator

 -96 dBm Sensitivity for Bluetooth low

energy

 12 bit /200K SPS ADC

BT-500

Application

 Advanced wearables

• Connected watches

• Advanced personal fitness devices

• Wearables with wireless payment

• Connected health

• Virtual/Augmented Reality applica-

Features

 Small footprint: 11.3×20×1.8mm

26-pin perforated hole.

 Bluetooth 5 ready multiprotocol radio

 Bluetooth 5 data rate support: 2 Mbs,

tions

 Internet of Things (IoT)

• Smart home sensors and controllers

• Industrial IoT sensors and control­lers

 Interactive entertainment devices

• Advanced Remote controls

• Gaming controllers

150, Jian Yi Road, Zhonghe District, New Taipei City, Taiwan 235, R.O.C.

8F, No.
Tel: [phone] Fax: [phone]

晶訊科技股份有限公司

CC&C Technologies, Inc.

Revision History

Version Date Change Description

1.0 11/3, 2017 Initial release

Data Sheet

BT-500

Note： All electrical and mechanical specifications may be changed by CC&C Technologies, Inc.

without notice.

8F, No. 150, Jian Yi Road, Zhonghe District, New Taipei City, Taiwan 235, R.O.C.
Tel: [phone] Fax: [phone]

Data Sheet

Pin Definition

Pin Signal Function Description

1 GND Ground Ground

2 P0.17 I/O Programmable I/O

3 P0.12 I/O Programmable I/O

4 VBUS Power Operating supply voltage 4.35~5.5V

5 P0.29 GPIO. Programmable I/O , Analog input

6 GND Ground Ground

7 VDD Power Operating supply voltage 1.7~3.6V

8 P0.26 I/O Programmable I/O

9 P0.04 I/O Programmable I/O, Analog input

10 P0.01 I/O Programmable I/O

11 P0.02 I/O Programmable I/O, Analog input

12 P0.00 I/O Programmable I/O

13 P1.15 I/O Programmable I/O

BT-500

14 DCC I/O DC/DC converter output

15 DEC4 I/O 1.3 V regulator supply decoupling

16 SWDIO Debug Debug serial data

17 SWDCLK Debug

18 P1.00 I/O Programmable I/O

19 P0.24 I/O Programmable I/O

20 P0.03 I/O Programmable I/O, Analog input

21 P1.14 I/O Programmable I/O

22 P1.13 I/O Programmable I/O

23 P1.11 I/O Programmable I/O

24 P0.10 I/O Programmable I/O

25 P0.09 I/O Programmable I/O

26 P1.06 I/O Programmable I/O

27 P0.18/RESET I/O Programmable I/O ,Configurable as system RESET

28 P1.02 I/O Programmable I/O

29 P1.04 I/O Programmable I/O

30 P0.20 I/O Programmable I/O

31 P1.10 I/O Programmable I/O

32

RFIO_OUT RF

Serial wire debug clock input for debug and programming

BT RF port

33 GND Ground Ground

34 VBUS Power Operating supply voltage 4.35~5.5V

35 USB_DP I/O USB D+

36 USB_DN I/O USB D-

37 GND Ground Ground

晶訊科技股份有限公司

CC&C Technologies, Inc.

Data Sheet

SPECIFICATION

BT-500

Product Name

Model Number

Operating Frequency

Tx power(max)

Bluetooth 5.0 Dongle

BT-500

2402-2480GHz

6dBm

Receiver sensitivity -96dBm

Power Voltage Range

Symbol Description Min. Typ. Max. Units

VBUS System power voltage 4.3 5 5.5 V

VCC_IO I/O power voltage -0.3 3.9 V

Tx mode 0dBm 11.6 mA

Current

Tx mode 6dBm

27.6 mA

Consumption

Rx mode 12.9 mA

Storage Temperature -40 25 125

o

C

晶訊科技股份有限公司
CC&C Technologies, Inc.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part

15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment causes harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

doing one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End

users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain

compliance with FCC exposure compliance requirement, please follow operation instruction as documented in

this manual.