CC and C Technologies BT0002M Original manual

Bluetooth Module

User’s Guide

Version 1.0

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

? Reorient or relocate the receiving antenna.
? Increase the separation between the equipment and receiver.
? Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

? Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface

cables when connecting to computer or peripheral devices). Any changes or
modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be
installed such that 20cm may be maintained between the antenna and users (for
example access points, routers, wireless ADSL modems, and similar equipment). The
final end product must be labeled in a visible area with the following: “Contains TX

FCC ID: PANBT0002M”.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE

1. General Description

CC&C BT-0002M Bluetooth module class II is powered by CSR BlueCore2, which

with RF and baseband function been integrated in a single chip and was designed for
Bluetooth 2.4 GHz wireless applications. With band-pass filter, balun, crystal and
flash memory built on, it can reduce external components and provide a hardware
engineer with a speed and convenient way to complete their designs. Because of
compact sizes, they can easily design into customers’ target devices. For instance,
they can be used for PDA, notebook, tablet PC, keyboard and mouse as an internal
module. The BT-0002M develops the Bluetooth protocol stacks, profiles and with a
plenty of software development and integration experiences, CC&C can help
customer to design a specific device.

2. General Specification

Model Name BT-0002M
Product Name BT Module (CSRBC02)-Class II
Size 52x19x2.7mm
Weight 2.8 gram
Specification Bluetooth spec. 1.1
Antenna terminal 50 Ohm
Power Class Class-II
Digital interface Board to board connector for

USB interface or

UART interface
Operating Voltage 3.3V +/- 0.3V ; 5V (USB)
Operating Current TBD
Operating Temp.

-10 ~ 70℃

3. Pin assignment

4. General Radio Characteristics

Transmitter Min Typ Max Unit Remarks

Maximum RF Output Power -2 0 2.55 dBm
RF Power control range 25 dBm

Initial Carrier Freq accuracy
Carrier Freq drift

DH5

±140

±115

±175

±25
±25
±20
±40
±20
±40
±20

kHz 11110000modModulation Characteristics
kHz 1010mod
kHz PRBS9
kHzDH1
kHz/50us Drift Rate
kHzDH3
kHz/50us Drift Rate
kHz
kHz/50us Drift Rate

20dB bandwidth for
modulated carrier

|M-N|=2 -20 dBmIn-band spurious

emissions

|M-N|>=3

-40 dBm

Receiver Min Typ Max Unit Remarks
Sensitivity DH1, DH3, DH5

Interference
Performance

C/I

CO-Channel

C/ I
C/ I
C/ I
C/ I
C/ I

1MHz
2MHz
2MHz
Image
Image

- -75 - dBm
TBD 11 dB
TBD 0 dB
TBD -30 dB *1
TBD -40 dB *1
TBD -9 dB
TBD -20 dB *1

Intermodulation Characteristics TBD dBm
Out-of-band
Blocking

30MHz-2000MHz -10 dBm
2000-2399MHz -27 dBm
2498-3000MHz -27 dBm
3GHz-12.75GHz -10 dBm