CBC EA 900RT 2KVAS, EA 900RT 3KVAS, EA 900RT 1KVAR, EA 900RT 2KVAR, EA 900RT 3KVAR User Manual

www.cbcinter.co.th

o

nline UPS

1KVA ~ 3KVA

1KVA ~ 3KVA

R

Uninterruptible Power Supply

R

1

TRUE ON LINE UPS

Contents

1. Introduction

2. Safety Instructions

3. Description of commonly used Notations

4. System Description

5. Connection and Operation

6. Trouble Shooting

7. Maintenance

8. Technical data

9. Communication Port

10. Appendix

1. Introduction

This On-Line-Series is an uninterruptible power supply incorporating double-converter
technology. It provides perfect protection specifically for Novell, Windows NT and
UNIX servers.
The double-converter principle eliminates all mains power disturbances. A rectifier
converts the alternating current from the socket outlet to direct current. This direct
current charges the batteries and powers the inverter. On the basis of this DC voltage,
the inverter generates a sinusoidal AC voltage, which permanently supplies the loads.
Computers and periphery are thus powered entirely by the mains voltage. In the event
of power failure, the maintenance-free batteries power the inverter.
This manual covers the UPS listed as follows. Please confirm whether it is the model
you intend to purchase by performing a visual inspection of the Model No. on the rear
panel of the UPS.

Model
1KVAS
1KVAR
2KVAS
2KVAR
3KVAS
3KVAR
6KVAS
6KVAR
10KVAS

Type

Model
1KVAH
1KVARH
2KVAH
2KVARH
3KVAH
3KVARH
6KVAH
6KVARH
10KVAH

Type

Standard Long backup time

Remark:

S Model: with inbuilt battery for short backup time
H Model: with external battery for long backup time.
R Model: Rack mount model

1
2
5
6
14
21
23
24
27
28

2

3

TRUE ON LINE UPS TRUE ON LINE UPS

2. Safety Instructions

PLEASE READ THE FOLLOWING USER MANUAL AND THE SAFETY INSTRUCTIONS
BEFORE INSTALLING THE UNIT AND STARTING IT UP!

2-1 Transport

Please transport the UPS system only in the original packaging (to protect against
shock and impact).

2-2 Set-up

Condensation may occur if the UPS system is moved directly from a cold to a
warm environment. The UPS system must be absolutely dry before being installed.
Please allow an acclimatization time of at least two hours.
Do not install the UPS system near water or in damp environments.
Do not install the UPS system where it would be exposed to direct sunlight or near heat.
Do not block off ventilation openings in the UPS system's housing.

2-3 Installation

Do not connect appliances or items of equipment which would overload the UPS
system (e.g. laser printers) to the UPS outlet socket
Place cables in such a way that no one can step on or trip over them.
Do not connect domestic appliances such as hair dryers to UPS output sockets.
The UPS can be operated by any individuals with no previous experience

Installation for 1K / 2K / 3K

Connect the UPS system only to an earthed shockproof socket outlet.
The building wiring socket outlet (shockproof socket outlet) must be easily accessible
and close to the UPS system.
This is operator installable
When installing the equipment, it should ensure that the sum of the leakage current
of the UPS and the connected consumer does not exceed 3.5mA.

Installation for 6K / 10K

Warning: This is a product for restricted sales distribution to informed partners.
Installation restrictions or additional measures may be needed to prevent disturbances.
A readily accessible disconnect device shall be incorporated in the building installation
wiring and must be close to the UPS system.
This is permanently connected equipment and only qualified maintenance personnel
may carry out installations.

2-4 Operation

Do not disconnect the mains cable on the UPS system or the building wiring
socket outlet (shockproof socket outlet) during operations since this would cancel
the protective earthing of the UPS system and of all connected loads.
The UPS system features its own, internal current source (batteries). The UPS
output sockets or output terminals block may be electrically live even if the UPS
system is not connected to the building wiring socket outlet.
In order to fully disconnect the UPS system, first press the Standby switch then
disconnect the mains lead
Ensure that no fluids or other foreign objects can enter the UPS system.
The UPS operates with hazardous voltages. Only qualified maintenance personnel
may carry out repairs

2-5 Maintenance, servicing and faults

The UPS system operates with hazardous voltages. Repairs Should be carried out
only by qualified maintenance personnel.
Caution - risk of electric shock. Even after the unit is disconnected from the mains
power supply (building wiring socket outlet), components inside the UPS system
are still connected to the battery and are still electrically live and dangerous.
Before carrying out any kind of servicing and/or maintenance, disconnect the
batteries and verify that no current is present and no hazardous voltage exist in the
terminals of high capability capacitor such as BUS-capacitors.

4

5

TRUE ON LINE UPS TRUE ON LINE UPS

For 6K / 10K models, the maintain switch, bypass switch and input switch are
still electrically live and dangerous even after the input switch and bypass
switch are disconnected on carrying out servicing and/or maintenance.
Only persons that are ade quately fam iliar w ith batteries and wi th the required
precautionary measures may replace batteries and supervise operation s. Unauthorised
persons must be kept well away from the batteries.
Caution - risk of electric shock. The battery circuit is not isolated from the input
voltage. Hazardous voltages may occur between the battery terminals and the ground.
Before touching, please verify that no voltage is present!
Batteries may cause electric shock and have a high short-circuit current. Please
take the precautionary measures specified below and any other measures necessary
when working with batteries:

--remove wristwatches, rings and other metal objects

--use only tools with insulated grips and handles.
When changing batteries, install the same number and same type of batteries.
Do not attempt to dispose of batteries by burning them. This could cause battery
explosion.
Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin
and eyes. It may be toxic.
Please replace the fuse only by a fuse of the same type and of the same amperage
in order to avoid fire hazards.
Do not dismantle the UPS system.

3. Description of commonly used notations

Some or all of the following Notations may be used in t his manu al and may appear
in your application process. Therefore, all users should be f amiliar with t hem and
understand their explanations.

Explanation
Alert you to pay special attention
Caution of high voltage
Turn on the UPS
Turn off the UPS
Idle or shut down the UPS
Alternating current source(AC)
Direct current source(DC)
Protective ground
Alarm silence
Overload indication
Battery check
Recycle
Display cycle button
Battery

Notation and Explanation

Notation

ON

OFF

6

7

TRUE ON LINE UPS TRUE ON LINE UPS

4. System Description

FunctionSwitch

ON - Switch

OFF-Switch

1. Turn on UPS system:
By pressing the ON-Switch I the UPS system is turned on.

2. Deactivate acoustic alarm:
By pressing this switch an acoustic alarm can be deactivated.

When mains power is normal, the UPS system switches to Standby mode
by pressing OFF-Switch . It is then switched to Bypass and the
inverter is off.
At this moment, the output sockets are supplied with voltage via the bypass
if the mains power is available.

LINE LED

1. The green LINE LED lights up if mains voltage is applied to the
UPS input.

2. LINE LED blinks when the phase and neutral conductor have been
reversed at the input of the UPS system.

3. If LINE LED and BATTERY-LED light up, the mains power supply
is out of tolerance.

BATTERY LED

The orange-coloured BATTERY-LED lights up when the mains power has
failed and the inverter is being powered by the batteries.

The orange-coloured BYPASS LED lights up when the UPS system is
supplying voltage provided by the mains power via the bypass.

The green-coloured INVERTER LED lights up if the UPS system is
supplying voltage provided by the mains power via the inverter.

The red FAULT LED lights up and an acoustic warning signal is issued
continuously when the UPS system is in fault condition. Press the Standby
switch in order to turn off the warning tone.

BYPASS LED

INVERTER LED

FAULT LED

BYPASS

AC INPUT AC OUTPUT

BATTERY

ON

OFF

FunctionDisplay

LOAD/
BATTERY
CAPACITY
LEDs

1. These LEDs show the load of the UPS system if the mains power is
available (normal operation):
2nd LED 96%-105 % 3rd LED 76%-95 %
4th LED 56%-75 % 5th LED 36%-55 %
6th LED 0-35 %

2. In the battery operation, the LEDs indicate the capacity of the batteries:
2nd LED 0-25 % 3rd LED 26%-50 %
4th LED 51%-75 % 5th LED 76%-95 %
6th LED 96%-100 %

6 Load/Battery Capacity LED
5 Load/Battery Capacity LED
4 Load/Battery Capacity LED
1 Fault LED
2 Load/Battery Capacity LED
3 Load/Battery Capacity LED
7 Bypass LED
9 Inverter LED
10 Battery LED
8 Line LED

2 Load/Battery Capacity LED

3 Load/Battery Capacity LED

4 Load/Battery Capacity LED

5 Load/Battery Capacity LED

6 Load/Battery Capacity LED

9 Inverter LED

10 Battery LED

7 Bypass LED

8 Line LED

1 Fault LED

Figure 1: LED Display Panel 1

1 Fault LED

2 Load/Battery Capacity LED

7 Bypass LED

9 Inverter LED
10 Battery LED

8 Line LED

ON-Switch/Alarm Silence

OFF-Switch

3 Load/Battery Capacity LED
4 Load/Battery Capacity LED
5 Load/Battery Capacity LED
6 Load/Battery Capacity LED

Figure 2: LED Display Panel 2

Figure 3: LEDR Display Panel

8

9

TRUE ON LINE UPS TRUE ON LINE UPS

BYPASS

AC INPUT AC OUTPUT

BATTERY

UPS work at bypass model, press the Display cycle button on front panel,
LCD will display as follows:

WELCOME TO USE
ONLINE UPS

WELCOME TO USE
ONLINE UPS

SYSTEM NORMAL

BYPASS OUPRUT

SYSTEM NORMAL

BYPASS OUPRUT

UPS work at inverter model, press the Display cycle button on front panel,
LCD will display as follows:

SYSTEM NORMAL

MAINS IN USE

SYSTEM NORMAL

MAINS IN USE

Press the Display cycle button on front panel once more, LCD will display
as follows:

Here display the input main power voltage parameter, this numerical value can
inspect main power voltage variety, from 0V~290V.

INPUT VOLTAGE

220.0V

INPUT VOLTAGE

220.0V

Main power in or first time UPS ON LCD display:

LCD display content and relative work model

LCD Display Screen

Line LED
Bypass LED

Inverter LED
Fault LED
Battery LED

Display Cycle Button

LCD Display Screen
Bypass LED
Line LED

Inverter LED

Fault LED
Battery LED
ON-Switch/Alarm Silence

OFF-Switch
Display Cycle Button

LCD Display Screen

Bypass LED
Line LED
Inverter LED

Fault LED
Battery LED
ON-Switch/Alarm Silence

OFF-Switch
Display Cycle Button

Figure 4: LCD Display Panel 1

Figure 5: LCD Display Panel 2

Figure 6: LCDR Display Panel

SERVICE