the wall
BATH CABINET
hardware
Thank you for purchasing The Wall bath cabinet. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
components
12 - dowels
3 - hinges
12 - bolts 8 - shelf
pins
Missing hardware?
Please call 800.606.6387 for
replacements.
18 - screws
mounting hardware
4 -plastic
anchors
4 -small
screws
4 -large
screws
4 -mounting
brackets
tools required
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
2 -wall
straps
1 - top panel
2 - side panels
(1 left, 1 right)
Made in Vietnam - r02 Page 1 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
1 - bottom panel 1 - fixed shelf
1 - door
1 - back panel
2 - adjustable
shelves
the wall
NOTE: Do not over
tighten the bolts.
BATH CABINET
fixed shelf
B
right side
panel
A
A
left side
panel
A. Insert 2 dowels into left side panel as shown.
B. Fit fixed shelf onto dowels, and attach to side
panel with 2 bolts. Secure, but do not over tighten
1
bolts with a phillips head screwdriver.
C
A. Insert 2 dowels into fixed shelf as shown.
B. Fit back panel into corresponding slot in left
side panel.
C. Fit right side panel onto dowels and back
2
panel, and attach to side panel with 2 bolts.
top
panel
B
back
panel
A
B
A
bottom
panel
A. Insert 4 dowels into side panels as shown.
B. Attach bottom panel to assembly and secure
3 4
with 4 bolts.
Made in Vietnam - r02 Page 2 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
B
A. Insert 4 dowels into side panels as shown.
B. Attach top panel to assembly and secure with
4 bolts.
the wall
BATH CABINET
NOTE:
Door can be
installed on
either left or
right side
door
Fit 3 hinges into door as shown and attach with 2
screws per hinge. Secure, but do not over tighten
5
screws with a screwdriver.
Attach door to case assembly by aligning holes in
hinges with holes in side panel. Secure each
6
hinge with 4 screws.
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners.
Insert 8 shelf pins at desired shelf heights. Place
each adjustable shelf on pins, making sure shelf
is securely supported by shelf pins.
7
Assembly is now complete.
Made in Vietnam - r02 Page 3 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
the wall
For added safety and stability, it is recommended that the wall mounting
hardware be installed. For safe mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to
wood studs whenever possible.
NOTE: If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional or your local
hardware store.
A) Attach 2 mounting brackets to top of unit using 2 small screws per
bracket.
B) Determine the final location of unit. Mark position on the wall,
approximately 2" below the mounting bracket mounted to the back of the
unit.
C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in
the wall that is slightly smaller in diameter than the anchor. Gently tap the
plastic anchor until the flange of the anchor is flush with the wall.
D) Attach 2 mounting brackets to the wall by inserting 2 large screws
through each mounting bracket and into the wall anchor.
E) Place the unit so the mounting brackets on the back edge are aligned
with the wall brackets.
F) Lace one end of each wall strap through brackets, and into the other
end of the strap.
G) Pull the strap tightly until secure.
Wall mounting assembly is now complete.
BATH CABINET
D
A
C
F
hinge adjustment
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as
illustrated.
1
A
B
Side to side adjustment:
Loosen screw A, adjust gap with
screw B and re-tighten screw A
A
Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw A and secure screw B with
a 1/4 turn clockwise
B
2
3
A
B
Height adjustment:
Loosen screw A & B, adjust door
height and re-tighten screws A&B
Made in Vietnam - r02 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...