Page 1
stowaway BED
hardware
Thank you for purchasing the Stowaway Bed. This
page
lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are recommended to safely assemble this product.
to this product. As you
12 - spring
washers
4 - cam
screws
Missing hardware? Please call 800.606.6387
for replacements.
12 - flat
washers
4 - small bolts4 - cams
16 - small
screws
8 - brackets
8 - large bolts
48 - large
screws
tools required
allen wrench (included)
(We recommend the use of hand tools instead of power tools)
phillips head screwdriver
components
2 - partitions
6 - drawer bottoms
2 - side panels
(1 left, 1 right)
2 - long
crossbars
1 - center
panel
6 - drawer fronts
2 - short
crossbars
2 - slat
assemblies
6 - drawer backs
12 - drawer sides
(6 left, 6 right)
Made in Vietnam - r12 Page 1 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 2
stowaway BED
NOTE: Do not over
tighten the bolts
partition
Fit pre-assembled dowels of 2 short crossbars
into corresponding holes of 1 partition as shown.
Secure each short crossbar with 1 flat washer,
1 spring washer and 1 small bolt, using an
allen wrench. Do not over tighten the bolts.
short crossbar
short crossbar
1
Fit pre-assembled dowels of 2 short crossbars
into corresponding holes of remaining partition
as shown. Secure each short crossbar with 1
flat washer, 1 spring washer and 1 small bolt,
using a allen wrench.
partition
2
Made in Vietnam - r12 Page 2 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 3
stowaway BED
partition
With the assistance of another adult, fit slots
of center panel into corresponding slots of
partitions as shown.
center panel
partition
3
NOTE: Do not over
tighten the screws
Secure center panel to partitions with 4
small screws as shown, using a phillips
head screwdriver. Do not over tighten the
screws.
4
Made in Vietnam - r12 Page 3 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 4
stowaway BED
NOTE: Do not over
tighten the cam screws
NOTE: Make sure
bottom of long crossbar
faces up as shown
5
A
long
crossbar
NOTE: Make sure arrow
of each came points toward
nearest edge with holes
Bottom
Fit 2 cam screws into 2 long crossbars as
shown. Secure, but do not over tighten, each
cam screw using a phillips head screwdriver.
A. Fit 4 cams into partitions as shown. Make
sure arrow of each cam points towards nearest
edge with holes.
B. Fit cam screws of each long crossbar into
corresponding holes of partitions as shown.
Using a screwdriver, turn each cam clockwise
until it securely engages each cam screw.
long
crossbar
B
A
long
crossbar
NOTE: Long crossbars should
overhang on top of partitions
6
Made in Vietnam - r12 Page 4 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 5
stowaway BED
A
large bolt
spring washer
flat washer
bracket
A. Fit pre-assembled dowels of long
crossbars into corresponding holes of
right side panel. Loosely attach right side
panel to assembly with 4 brackets, 4 flat
washers, 4 spring washers and 4 large
bolts.Repeat for left side panel.
B. At this point, secure left and right side
panels to long crossbars by fully
tightening all bolts using an allen wrench
at a 45º. Do not over tighten the bolts.
C. At this point, secure left and right side
panels to center panel by fully tightening
all bolts.
left side
panel
B
long
crossbar
center panel
long
crossbar
C
right side
panel
7
Made in Vietnam - r12 Page 5 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 6
stowaway BED
left side
panel
center
panel
Secure center panel to left and right side
panels with 2 small screws per side as
shown, using a screwdriver.
right side
panel
8
drawer
side
NOTE: Make sure grooves of
drawer side and drawer back
are positioned as shown
drawer
front
Fit dowels of drawer front into corresponding holes of drawer side. Secure drawer front to
drawer side with 2 large screws as shown, using an allen wrench.
9
Made in Vietnam - r12 Page 6 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 7
stowaway BED
drawer
bottom
drawer
back
Slide drawer bottom into corresponding
10 11
grooves of drawer assembly as shown.
Attach dowels of drawer back into corresponding holes of drawer side. Secure drawer side
to drawer back with 2 large screws as shown.
Fit remaining drawer side into corresponding
holes of drawer back and front as shown and
secure with 4 large screws. Repeat steps 9-12
for all remaining drawer assemblies.
drawer
side
12
Made in Vietnam - r12 Page 7 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 8
stowaway BED
13
Slide drawer assemblies into assembled
unit as shown.
drawer
assembly
With the assistance of another adult, attach
2 slat assemblies to assembled unit with 8
small screws as shown, using a screwdriver.
Assembly is now complete.
14
cleaning & care
Made in Vietnam - r12 Page 8 of 8
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners.
NOTE: Each drawer box can support maximum weight of 105 lbs
Loading...