Page 1
shake
TALL CHEST
assembly hardware
Thank you for purchasing the Shake Tall Chest. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
components
12 - wood
dowels
12 - bolts 32 - screws
mounting hardware
4 - plastic
anchors
Missing hardware? Please call 800.606.6387 for replacements.
4 - small
screws
4 - large
screws
4 - mounting
brackets
tools required
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
2 - wall
straps
1 - top panel
2 - side panels
(1 left, 1 right)
1 - back panel
1 - center panel
8 - drawer sides
4 - drawer fronts
Made in Vietnam - r03 Page 1 of 6
(4 left, 4 right)
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
4 - drawer backs
1 - bottom panel
4 - drawer bottoms
Page 2
shake
left and right
side panels
TALL CHEST
bottom
panel
top
panel
Insert 2 wood dowels into left and right side
1 2
panels as shown.
left side
panel
center
panel
With assistance of another adult, fit dowels of left and right
side panels into corresponding holes of center panel and
attach with 4 bolts. Secure, but do not over tighten, bolts
3
with a phillips head screwdriver.
Insert 4 wood dowels into top and bottom panel.
Note: Do not over
tighten the bolts
right side
panel
Made in Vietnam - r03 Page 2 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 3
shake
TALL CHEST
bottom
panel
4
Fit dowels of bottom panel into corresponding
holes of assembly and attach with 4 bolts.
back
panel
top
panel
With assistance, position unit upright. Insert back
5 6
panel into corresponding grooves of assembly.
Made in Vietnam - r03 Page 3 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Fit dowels of top panel into corresponding holes of
assembly and attach with 4 bolts.
Page 4
shake
drawer front
TALL CHEST
left drawer
side
drawer
bottom
Attach left drawer side to drawer front with 2
screws. Secure, but do not over tighten, screws
with a screwdriver.
7 8
drawer
back
Fit drawer bottom into corresponding grooves of
drawer assembly.
right drawer
side
Attach right drawer side to drawer assembly with
Attach drawer back to left drawer side with 2
9 10
screws.
Made in Vietnam - r03 Page 4 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
4 screws.
Repeat steps 7-10 for remaining drawers.
Page 5
shake
NOTE: Make sure glides are pulled
out of the case and ball bearings are
at the front of the extended glides.
To prevent damage to glides, keep drawer
assembly level during installation.
TALL CHEST
11
Fit drawer glides of each drawer into
corresponding drawer glides of case assembly.
Make sure drawer glides securely engage.
Assembly is now complete.
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not
use abrasive cleaners.
drawer
assembly
Made in Vietnam - r03 Page 5 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 6
shake
TALL CHEST
C
A
D
E
optional wall mounting instructions
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.).
Mount to wood studs whenever possible.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a
qualified professional or your local hardware store.
A. Attach 2 brackets to the top of the assembled unit with 2 small screws per bracket.
B. With the assistance of another adult, place the unit in desired location against the wall. Mark the
location of the hole in the bracket on the wall. Move the unit out of the workspace.
C. Drill holes slightly smaller in diameter than the anchors. Insert 1 plastic anchor into each hole until
they are flush to the wall.
D. Insert 2 large screws through each bracket and plastic anchor. Secure, but do not over tighten
with a phillips head screwdriver.
E. Place the unit back into position against the wall and thread the wall strap through both brackets
and pull until tight.
Wall mounting assembly is now complete.
Made in Vietnam - r03 Page 6 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...