rodney TALL CHEST
hardware
Thank you for purchasing the Rodney Tall Chest. This
page
lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components
for assembly, place the contents on a carpeted or
padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
to this product. As you unpack and prepare
components
12 - spring
washers
4 - brackets
12 - flat
washers
6 - small
screws
8 - small
bolts
Missing hardware? Please call
800.606.6387 for replacements.
4 - large
bolts
32 - screws
mounting hardware
4 - wall
brackets
4 - plastic
anchors
4 - small
screws
4 - large
screws
tools required
allen wrench
(included)
(We recommend the use of hand tools instead of power tools)
philips head screwdriver
2 - wall
straps
1 - top panel
1 - bottom panel
1 - back panel
Made in Vietnam - r06 Page 1 of 5
Customer Service 800.606.6252 I Latest instructions available on www.cb2.com
4 - drawer
fronts
4 - drawer
bottoms
2 - side panels
(1 left, 1 right)
4 - drawer
backs
2 - legs
1 - middle panel
L
8 - drawer sides
(4 left, 4 right)
R
rodney
middle
panel
TALL CHEST
NOTE: Do not over
tighten the bolts.
right side
panel
left side
panel
With the assistance of another adult, carefully
place left/right side panels and middle panel
onto clean padded surface as shown. Attach
middle panel to left and right side panels with 4
brackets, 4 flat washers, 4 spring washers and
4 large bolts, using an allen wrench. Do not over
1
tighten the bolts.
NOTE: Make sure left
and right side panels are
assembled with grooves
facing back as shown
B
bottom panel
C
A
back panel
B
C
top panel
Position top panel as shown. Fit pre-assembled
dowels of left and right side panels into
corresponding holes of top panel. Secure left and
right side panels to top panel with 4 flat
washers, 4 spring washers and 4 small bolts as
2
shown, using a phillips head screwdriver.
leg
A. Slide back panel into grooves of left and right side panels.
B. Fit pre-assembled dowels of left and right side panels into
corresponding holes of bottom panel. Secure left and right side
panels to bottom panel with 4 flat washers, 4 spring washers
and 4 small bolts, using a phillips head screwdriver.
C. Secure back panel to top and bottom panel with 6 small
3 4
screws, as shown.
Made in Vietnam - r06 Page 2 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Attach 2 legs to assembled unit
by turning each leg clockwise
as shown.
rodney
NOTE: Do not over
tighten the screws
TALL CHEST
drawer
side
L
drawer
front
NOTE: Make sure glide
is positioned as shown
Fit pre-assembled dowels of drawer front into
corresponding holes of drawer side. Secure
drawer front to drawer side with 2 screws as
shown, using a phillips head screwdriver. Do not
over tighten the screws.
5 6
drawer
bottom
L
Slide drawer bottom into corresponding grooves
of drawer assembly.
drawer
back
L
Fit pre-assembled dowels of drawer side into
corresponding holes of drawer back. Secure
drawer back to drawer side with 2 screws
7 8
using a screwdriver.
drawer
R
side
L
Fit pre-assembled dowels of drawer back and
front into corresponding holes of drawer side.
Secure drawer side with 4 screws as shown
using a screwdriver. Repeat steps 5-8 for
remaining drawers.
Made in Vietnam - r06 Page 3 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
rodney
TALL CHEST
With the assistance of another adult, position
unit upright. Fit drawer glides of drawer into
corresponding drawer glides of assembly as
shown. Firmly push drawer into assembly until
the glides are securely engaged.
Assembly is now complete.
drawer
assembly
NOTE:
Make sure glides are
pulled out of the case, and
ball bearings are at the front of
the extended glides
9
NOTE: Make sure to
keep drawer level so
as not to damage glides
during assembly
cleaning & care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer.
Made in Vietnam - r06 Page 4 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
rodney TALL CHEST
safety mounting instructions
NOTE:
If you are unsure about your wall type or what mounting
method you should use, consult a qualified professional
or your local hardware store.
For added safety and stability, it is recommended that the
wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type
(i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
A) Attach 1 wall bracket to top of unit as shown, using 2
small screws per bracket.
B) Determine the final location of unit. Mark position on the
wall, approximately 2" below the bracket mounted to the
back of the cabinet.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller in
diameter than the anchor. Gently tap the plastic anchor
until the flange of the anchor is flush with the wall.
D) Attach the wall bracket to the wall by inserting 2 large
screws through the wall bracket and into the wall anchor in
the wall.
E) Place the unit so the wall bracket on the back edge is
aligned with the wall bracket.
F) Lace one end of the wall strap through both brackets,
and into the other end of the strap.
G) Pull the strap tightly until secure. Repeat steps for
remaining brackets and wall strap.
A
small
screw
F
wall
strap
wall
bracket
plastic
anchor
D
large
screw
C
wall
bracket
Made in Vietnam - r06 Page 5 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...