pezzo
STACKING STORAGE UNIT / BENCH
assembly hardware
Thank you for purchasing the Pezzo Stacking Storage
Unit / Bench. This page lists all the contents included in
the box. Please take the time to identify the hardware as
well as the individual components to this product. As you
unpack and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
components
4 - small
bolts
16 - cam
screws
2 - flat
washers
16 - cams
2 - spring
washers
(attached in side panels)
8 - small
screws
2 - metal
plates
mounting hardware
4 - large
screws
4 - small
screws
Missing hardware?
Please call 800.606.6387 for replacements.
4 - plastic
anchors
2 - wall
straps
2 - large
bolts
16 - cam
covers
4 - mounting
brackets
1 - top panel
1 - bottom panel
2 - partitions 1 - fixed shelf
2 - side panels 1 - leg
tools required
(We recommend the use of hand tools instead of power tools)
Made in Vietnam - r05 Page 1 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
phillips head screwdriver
allen wrench (included)
pezzo
NOTE: Make sure
arrow on each
cam points toward
nearest edge with holes
STACKING STORAGE UNIT / BENCH
A
fixed shelf
NOTE: Do not over
tighten the cam screws
B
partition
partition
fixed shelf
A
B
partition
A. Insert 4 cams into fixed shelf as shown.
B. Insert 2 cam screws and 2 cams into each
partition as shown, using a phillips head
1 2
screwdriver. Do not over tighten.
NOTE: Do not over
tighten the bolts
shelf
assembly
bottom
panel
center
B
leg
A
A. Fit pre-assembled dowels of fixed shelf into
corresponding holes of partitions as shown.
B. Using a screwdriver, turn each cam clockwise until it securely engages each cam screw.
side panels
A. Fit dowels of shelf assembly into corresponding holes of bottom panel as shown.
Secure bottom panel with 4 small bolts, using
a screwdriver. Do not over tighten the bolts.
B. Attach center leg to bottom panel as
3
shown. Turn leg clockwise to secure.
Made in Vietnam - r05 Page 2 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Insert 2 cams and 2 cam screws into each side
panel as shown.
4
pezzo
B
STACKING STORAGE UNIT / BENCH
top panel
A
A. Insert 4 cams into bottom of bottom panel
as shown.
B. Fit dowels of bottom panel into corresponding holes of each side panel. Secure cams.
5 6
A
B
A
top panel
Insert 8 cam screws into top panel as shown.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth. Do
not use abrasive cleaners.
WEIGHT LIMITATIONS
1 UNIT/MEDIA STAND: This item is able to
support up to a total of 53 lbs evenly
distributed.
1 UNIT/BENCH: This item is able to support
up to a total of 325 lbs evenly distributed.
A. Fit top panel onto corresponding dowels of
assembly as shown. Secure cams. At this
point, cover cams with cam covers.
B. Secure assembly with 2 large bolts, 2 spring
washers and 2 flat washers as shown, using
an allen wrench. Position unit upright.
7
Assembly is now complete.
Made in Vietnam - r05 Page 3 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
2-3 STACKED UNITS/BOOKCASE: This item
is able to support up to 130 lbs (top surface),
37lbs (side shelves) and 55lbs (center shelves);
all evenly distributed.
pezzo
Stacking instructions:
Attach 2 metal plates to back of stacked bookcases with 4 small screws per plate. Bookcases
can be stacked up to 3 bookcases high.
Please note:
- When stacking, the center support is only needed
on the bottom bookcase
- When stacking, product can only be used as a
bookcase, not a media stand
STACKING STORAGE UNIT / BENCH
WALL
C
D
A
F
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is
essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs
whenever possible.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified
professional or your local hardware store.
A) Attach 2 mounting brackets to top of unit using 2 small screws per bracket.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below the mounting bracket mounted to
the back of the unit.
C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the
anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall.
D) Attach 2 mounting brackets to the wall by inserting 2 large screws through each mounting bracket and into the wall
anchor in the wall.
E) Place the unit so the mounting brackets on the back edge are aligned with the wall brackets.
F) Lace one end of the wall strap through both brackets, and into the other end of the strap.
G) Pull the strap tightly until secure.
Wall mounting assembly is now complete.
Made in Vietnam - r05 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...