linear LOW DRESSER
hardware
Thank you for purchasing the Linear Low Dresser. This
page
lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are required to safely assemble this product.
to this product. As you unpack and prepare
components
12 - spring
washers
12 - flat
washers
20 - small
bolts
12 - large
bolts
32 - screws
mounting hardware
4 - wall
brackets
4 - plastic
anchors
Missing hardware?
Please call 800.606.6387 for replacements.
4 - small
screws
4 - large
screws
2 - wall
straps
tools required
allen wrench
(included)
(We recommend the use of hand tools instead of power tools)
philips head screwdriver
1 - top panel
1 - bottom panel
1 - back panel
Made in Vietnam - r05 Page 1 of 5
Customer Service 800.606.6252 I Latest instructions available on www.cb2.com
1 - left side
panel
4 - drawer
fronts
4 - drawer
bottoms
1 - partition 1 - right side
panel
4 - drawer
backs
5 - legs
8 - drawer sides
(4 left, 4 right)
linear LOW DRESSER
NOTE: Do not over
tighten the bolts.
right side
panel
top panel
With the assistance of another adult, carefully
place top panel upside down onto a clean,
padded surface. Fit pre-assembled dowels of left
and right side panels into corresponding holes of
top panel. Secure left and right side panels to top
panel with 2 flat washers, 2 spring washers and
2 large bolts as shown. Secure, but do not over
1
tighten bolts using a phillips head screwdriver.
NOTE: Make sure left
and right side panels are
assembled with grooves
facing back as shown
left side
panel
partition
Fit pre-assembled dowels of partition into
corresponding holes of top panel. Secure partition
to top panel with 2 flat washers, 2 spring
washers and 2 large bolts as shown, using a
2
screwdriver.
back panel
bottom panel
Carefully place bottom panel onto a clean,
padded surface. Attach 5 legs to bottom panel
Slide back panel into grooves of left and right
3 4
side panels.
Made in Vietnam - r05 Page 2 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
with 4 small bolts as shown. Secure, but do not
over tighten the bolts using an allen wrench.
linear LOW DRESSER
NOTE: Do not over
tighten the screws
bottom
panel
With the assistance of another adult, fit
pre-assembled dowels of left/right side panels and
partition into corresponding dowels of bottom
panel. Secure bottom panel with 6 flat washers,
6 spring washers and 6 large bolts using a
5 6
screwdriver.
drawer
front
“R” drawer
side
NOTE:
Open end
of glide
hardware
Secure drawer front to right and left drawer
sides with 4 screws as shown using a phillips
head screwdriver. Do not over tighten the screws.
“L” drawer
side
drawer
back
drawer
bottom
Fit drawer back onto drawer bottom and align
with corresponding holes of drawer sides. Secure
drawer back to drawer sides with 4 screws using
Slide drawer bottom into corresponding grooves
7 8
of drawer assembly.
Made in Vietnam - r05 Page 3 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
a screwdriver.
Repeat steps 6-8 for remaining drawers.
linear LOW DRESSER
NOTE:
Make sure glides are
pulled out of the case, and
ball bearings are at the front of
the extended glides
NOTE: Make sure to
keep drawer level so
as not to damage glides
during assembly
TL = top left drawer
TR = top right drawer
BL = bottom left drawer
BR = bottom right drawer
drawer
assembly
With assistance of another adult, insert glides of top left/right and bottom left/right drawer assemblies into
corresponding glides of case assembly. Keeping the drawer level, carefully push the drawer until it is all the way in
the case and glides are securely engaged.
Assembly is now complete.
9
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit is
finished with a protective clear lacquer. It is recommended to use coasters to protect surface from heat and water.
Made in Vietnam - r05 Page 4 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
linear LOW DRESSER
safety mounting instructions
For added safety and stability, it is recommended that
the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall,
concrete, etc.). Mount to wood studs whenever
possible.
A) Attach 1 wall bracket to top of unit as shown,
using 2 small screws per bracket.
B) Determine the final location of unit. Mark position
on the wall, approximately 2" below the bracket
mounted to the back of the cabinet.
C) Drill a hole in the wall stud. If the wall stud is not
available, drill a hole in the wall that is slightly smaller
in diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the
wall.
D) Attach the wall bracket to the wall by inserting 2
large screws through the wall bracket and into the
wall anchor in the wall.
E) Place the unit so the wall bracket on the back
edge is aligned with the wall bracket.
F) Lace one end of the wall strap through both
brackets, and into the other end of the strap.
G) Pull the strap tightly until secure. Repeat steps for
remaining brackets and wall strap.
A
small
screw
F
wall
strap
wall
bracket
plastic
anchor
D
large
screw
C
wall
bracket
NOTE:
If you are unsure about your wall type or what
mounting method you should use, consult a
qualified professional or your local hardware store.
Made in Vietnam - r05 Page 5 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...