gloss NIGHTSTAND
hardware
Thank you for purchasing the Gloss Nightstand. This
page
lists all the contents included in the box. Please
take the time to identify the hardware as well as the
individual components
and prepare for assembly, place the contents on a
carpeted or padded area to protect them from damage.
Note: 2 people are recommended to safely install this
product
.
to this product. As you unpack
components
8 - screws 4 - cams 4 - bolts
8 - wood
dowels
Missing hardware?
Please call 800.606.6387 for replacements.
4 - flat
washers
4 - spring
washers
tools required
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
4 - cam
screws
1 - top
panel
1 - back
panel
1 - drawer
back
Made in Vietnam - r04 Page 1 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
1 - bottom
panel
2 - side panels
(1 left, 1 right)
1 - drawer
front
2 - drawer sides
(1 left, 1 right)
1 - drawer
bottom
gloss NIGHTSTAND
NOTE: Make sure arrows
on each cam points towards
the nearest edge with holes
NOTE: Do not
over tighten
the cam screws
left and right
side panels
Insert 4 wood dowels and 2 cams into left and
right side panels as shown. Make sure arrows
on each cam points towards the nearest edge
1
with holes.
NOTE: Make sure grooves
of left and right side panels
are facing each other during
assembly as shown
left side
panel
right side
panel
top panel
Insert 4 cam screws into top panel as shown.
Secure, but do not over tighten, cam screws with
2
a phillips head screwdriver.
back panel
bottom
panel
Fit dowels on side panels into corresponding holes
of bottom panel as shown. Attach bottom panel
with 4 bolts, 4 spring washers and 4 flat washers,
using a screwdriver. Do not over tighten the bolts.
3
Made in Vietnam - r04 Page 2 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
NOTE: Do not
over tighten
the bolts
4
Position unit upright. Fit back panel into
corresponding grooves of side panels as shown.
gloss NIGHTSTAND
top
panel
NOTE: Do not
over tighten
the screws
drawer
front
A
left drawer
side
B
drawer
bottom
Fit top panel onto dowels of side panels. Using a
screwdriver, turn cams clockwise until it securely
engages the cam screws.
5
drawer
back
A. Attach left drawer side to drawer front with
2 screws as shown. Secure, but do not over
tighten, screws with a screwdriver.
B. Insert drawer bottom into grooves of drawer
side and front as shown.
6
right drawer
side
Attach drawer back to left side drawer with 2
7
Made in Vietnam - r04 Page 3 of 4
screws as shown.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
8
Attach right drawer side to drawer front and
back with 4 screws as shown.
gloss NIGHTSTAND
NOTE:
Make sure glides are
pulled out of the case, and
ball bearings are at the front of
the extended glides
Align drawer glides of drawer with corresponding drawer into
corresponding glides of case assembly. Keeping the drawer level,
carefully push the drawer until it is all the way in the case and glides are
securely engaged.
Assembly is now complete.
9
cleaning & care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer. It is
recommended to use coasters to protect surface from
heat and water.
Made in Vietnam - r04 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...