CB2 FUEL Assembly Instructions Manual

fuel CREDENZA
assembly hardware
Note: 2 people are required to safely assemble this product.
to this product. As you unpack and prepare
components
8 - flat washers
24 - small screws
8 - spring washers
8 - small bolts
6 - cams
12 - large bolts
6 - cam screws
4 - hinges 8 - shelf
12 - wood dowels
supports
mounting hardware
4 - small screws
Missing hardware? Please call 800.606.6387 for replacements.
4 - large screws
4 - plastic anchors
2 - wall straps
4 - mounting brackets
tools required
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
1 - top panel 1 - bottom panel 1 - back panel
1 - partition
2 - doors
Made in Vietnam - r06 Page 1 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
2 - adjustable shelves
4 - feet
(2A, 2B)
1 - right side panel1 - left side panel
1 - support foot
fuel CREDENZA
NOTE: Make sure arrows on each cam points toward nearest edge with holes
left and right
A
side panels
partition
B
A. Insert 4 wood dowels and 2 cams into left and right side panels as shown. Make sure
arrows on each cam points toward nearest edge with holes. B. Insert 4 wood dowels and 2 cams into
1
partition as shown.
NOTE: Do not over tighten the cam screws
top panel
Insert 6 cam screws into top panel as shown. Secure, but do not over tighten, screws using a
2
phillips head screwdriver.
NOTE: Make sure grooves of side and top panels are assembled on the same side
right side panel
top panel
Fit dowels of left/right side panels and partition into corresponding holes of top panel as shown. Using a screwdriver, turn each cam clockwise until it securely engages each cam screw.
3
NOTE: Make sure arrow label on partition points toward the front during assembly
partition
left side panel
back panel
Slide back panel into corresponding grooves of
4
left/right side panel and top panel as shown.
Made in Vietnam - r06 Page 2 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
fuel CREDENZA
NOTE: Make sure groove of bottom panel is assembled towards back panel
Fit dowels of left/right side panels and partition into corresponding holes of bottom panel. Secure
bottom panel to left/ride side panels and partition with 6 small bolts, 6 spring washers and 6 flat washers, using a phillips head
5
screwdriver. Do not over tighten the bolts.
NOTE: Do not over tighten the bolts
bottom panel
A
foot A
foot A
A
foot B
B
A. Attach 4 feet (2A, 2B) to bottom panel with 3 large bolts per foot as shown, using a screwdriver. B. Attach 1 support foot to bottom panel with 2
6
small bolts, 2 spring washers and 2 flat washers.
B
support foot
foot A
foot B
A
adjustable
B
shelf
A. With the assistance of another adult, position unit upright as shown. Insert 8 shelf supports at
desired shelf heights. B. Place 2 adjustable shelves into assembled
unit. Make sure shelves are securely supported by
7
each shelf support.
A
NOTE: Do not over tighten the screws
hinge
left and right doors
Fit 2 hinges into corresponding holes of 2 left and right doors as shown. Secure each hinge with 2
8
small screws, using a screwdriver.
Made in Vietnam - r06 Page 3 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
fuel CREDENZA
B
cleaning & care
A
left door front
right door front
A. Attach hinges of left and right door to left and right side panels as shown. Secure each hinge with 4 small screws. B. Secure the set screws with a screwdriver as shown. Refer to Hinge Adjustment diagram for adjusting the alignment of the door hinges.
9
Assembly is now complete.
hinge adjustment
If the doors do not appear square or aligned, loosen or tighten the appropriate screws on each case hinge as illustrated.
Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Do not use furniture wax or polish as the unit is finished with a protective clear lacquer. It is recommended to use coasters to protect surface from heat and water.
weight limitations
This credenza is rated to support 50 lbs, evenly distributed.
1) Side to side adjustment: Loosen screw A, adjust gap with screw B and re-tighten screw A.
Made in Vietnam - r06 Page 4 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
2) Depth adjustment: Loosen screw A, push hinge arm forwards or backwards, re-tighten screw A and secure screw B with a 1/4 turn clockwise.
3) Height adjustment: Loosen screw C, adjust door height and re­tighten screw C.
fuel CREDENZA
wall mounting assembly
C
mounting bracket
plastic anchor
wall strap
small screw
A
D
mounting bracket
large screw
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
WALL
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible. A) Attach mounting bracket to top of unit using 2 small screws. B) Determine the final location of unit. Mark position on the wall, approximately 2" below the mounting bracket mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the wall. D) Attach the mounting bracket to the wall by inserting 2 large screws through the mounting bracket and into the wall anchor in the wall. E) Place the unit so the mounting bracket on the back edge is allowed with the wall bracket. F) Lace one end of the wall strap through both brackets, and into the other end of the strap. G) Pull the strap tightly until secure.
Repeat step A-G for remaining wall mounting assembly.
Wall mounting assembly is now complete.
Made in Vietnam - r06 Page 5 of 5
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...