Page 1
facet
BOOKCASE
assembly hardware
Thank you for purchasing the Facet Bookcase. This page
lists all the contents included in the box. Please take the
time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
components
dowels
24 - bolts24 - wood
24 - flat
washers
24 - spring
washers
wall mounting hardware
2 - large
screws
2 - small
screws
Missing hardware?
Please call 800.606.6387 for replacements.
2 - plastic
anchors
2 - wall
straps
4 - mounting
brackets
tools required
allen wrench (included)
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
1 - top panel
1 - bottom panel
Made in Vietnam - r04 Page 1 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
2 - side panels
(1 left, 1 right)
4 - fixed shelves
Page 2
facet
left and right
side panel
BOOKCASE
NOTE: Do not over
tighten the bolts
fixed
shelf
left side
panel
Insert 12 wood dowels into right and left side
panels as shown.
1 2
right side
panel
NOTE: During assembly
make sure the angle at
the front of the shelf is
the same angle as the
side panel it attaches to.
top panel
Fit 4 fixed shelves onto corresponding dowels
of left side panel. Using an allen wrench,
secure but do not over tighten with 8 bolts, 8
spring washers and 8 flat washers as shown.
Fit 4 fixed shelves onto corresponding dowels
of right side panel, and secure with 8 bolts, 8
spring washers and 8 flat washers as shown.
3
Made in Vietnam - r04 Page 2 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Fit top panel onto dowels of assembly and
secure with 4 bolts, 4 spring washers and 4
flat washers as shown.
4
Page 3
facet
BOOKCASE
bottom
panel
5
Fit bottom panel onto dowels of assembly and
secure with 4 bolts, 4 spring washers and 4
flat washers as shown. With the assistance of
another adult, carefully position unit upright.
Assembly is now complete.
CLEANING AND CARE
Clean surfaces with a dry or damp soft cloth.
Do not use abrasive cleaners.
Made in Vietnam - r04
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 3 of 4
Page 4
facet
WALL
BOOKCASE
NOTE: Bookcae case be
wall mounted from either side
A
D
C
For added safety and stability, it is recommended that the wall mounting
hardware be installed. For safe mounting, it is essential to use wall anchors
appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to
wood studs whenever possible.
A) Attach 2 mounting brackets to top of unit using 1 small screw per
bracket.
B) Determine the final location of unit. Mark position on the wall,
approximately 2" below each mounting brackets mounted to the back of the
unit.
C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the
wall that is slightly smaller in diameter than the anchor. Gently tap the plastic
anchor until the flange of the anchor is flush with the wall.
D) Attach the mounting brackets to the wall by inserting 1 large screw
through each mounting bracket and into the wall anchor in the wall.
E) Position the unit so the mounting bracket on the back edge is allowed with
the wall bracket.
F) Lace one end of each wall strap through corresponding brackets, and into
the other end of the strap.
G) Pull the straps tightly until secure.
Wall mounting assembly is now complete.
NOTE:
If you are unsure about your wall
type or what mounting method
you should use, consult a
qualified professional or your
local hardware store.
Made in Vietnam - r04 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...