CB2 CROSSROADS Assembly Instructions Manual

crossroads BOOKSHELF
hardware
Thank you for purchasing the Crossroads Bookshelf. This page Please take the time to identify the hardware as well as the individual components unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
Note: 2 people are required to safely assemble this product.
lists all the contents included in the box.
to this product. As you
components
28 - wood dowels
8 - spring washers
8 - bolts
8- flat washers
26 - cam screws
Missing hardware? Please call 800.606.6387 for replacements.
26 - cams 26 - cam
mounting hardware
4 - small screws
4 - large screws
4 - plastic anchors
2 - wall straps
tools required
phillips head screwdriver
2.5mm (1/16”) drill bit
covers
4 - wall brackets
1 - bottom panel
1 - top panel
3 - small shelves
Made in Vietnam - r09 Page 1 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
2 - large shelves
2 - side panels
2 - back panels
(1 left, 1 right)
crossroads BOOKSHELF
Make sure arrows on each cam point toward nearest edge with holes
A
small shelf
NOTE: Do not over tighten the cam screws
Cam in unlocked position
C
B
top panel
A. Insert 6 cams into each small shelf as shown. Make sure arrows on each cam point toward the nearest edge with holes. B. Insert 8 cam screws into top panel as shown. Secure, but do not over tighten, screws using a phillips
head screwdriver. C. Insert 4 wood dowels and 2 cams into each large shelf as shown.
1
large shelf
small shelf
small shelf
Cam in locked position
small shelf
side panel
A. Insert 6 cam screws, 10 wood dowels and 2 cams into each side panel as shown. B. Insert 3 cam screws into left and right back
2 3
panels as shown.
Made in Vietnam - r09 Page 2 of 4
A
left and right back panel
B
Fit dowels of side panel into corresponding holes of small shelves as shown. Turn each cam clockwise until it securely engages each cam screw, using a phillips head screwdriver.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
side panel
crossroads BOOKSHELF
side panel
Fit dowels of remaining side panel into corresponding holes of small shelves as shown.
4 5
Secure all cams.
NOTE: Make sure red arrows on large shelves are pointing the same direction during assembly
With the assistance of another adult, position assembled unit as shown. Fit notches of large shelves into corresponding notches of assembled unit as shown.
large shelf
large shelf
Fit cam screws of left and right back panels into corresponding holes of assembled unit as shown. Do not secure cams until further instructions.
6 7
Made in Viietnam - r09 Page 3 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
NOTE: Do not over tighten the bolts
Attach bottom panel to assembled unit as shown with 8 bolts, 8 spring washers and 8 flat washers. Secure, but do not over tighten, bolts using a phillips head screwdriver.
crossroads BOOKSHELF
Fit dowels of assembled unit into corresponding holes of top panel as shown.
With assistance of another adult, position unit upright, while supporting back panels of assembly. At this point, secure all cams in top
and back panel. Cover all exposed cams with cam covers.
98
Assembly is now complete.
wall mounting assembly
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood studs whenever possible.
A) With a 2.5mm (1/16”) drill bit, drill two holes to the top of unit. Attach 2 wall brackets with 2 small screws per bracket as shown. B) Determine the final location of unit. Mark position on the wall, approximately 2" below the wall bracket mounted to the back of the unit. C) Drill a hole in the wall stud. If the wall stud is not available, drill a hole in the wall that is slightly smaller in diameter than the anchor. Gently tap each plastic anchor until the flange of the anchor is flush with the wall. D) Attach 2 wall brackets to the wall by inserting 2 large screws through the wall bracket and into the wall anchor in the wall. E) Place the unit so the wall bracket on the back edge is aligned with the wall bracket. F) Lace one end of the wall strap through both brackets, and into the other end of the strap. G) Pull the strap tightly until secure.
Repeat step A-G for remaining wall mounting assembly.
Wall mounting assembly is now complete.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a qualified professional or your local hardware store.
C
D
A
F
WALL
Made in Vietnam - r09 Page 4 of 4
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Loading...