Cayken PODR2180 Product Manual

OPERATING INSTRUCTION -8

CONTENTS

Warning

Thanks to the buyer

About this manual

Product instructural brief introduction

Technical parameter

Technical characteristic describes

Safe working instruction

Preparatory stage

Begin to operate

Friction clutch

Mains switch and integral over current protection

Gear speed adjustment

............................................................................................................

...........................................................................................

.............................................................................................

................................................................

...........................................................................................

.........................................................................

.....................................................................................

...............................................................................................

................................................................................................

...................................................................................................

......................................................................................

................................................

1

1

1

2

3

3

4

5

6

7

7

7

Oil soak type advantage

Common fault and the method of removing

Maintenance

Quality guarantee

......................................................................................................

..............................................................................................

.....................................................................................

........................................................

8

9

10

10

Operation Manual

WARNING

To prevent electric shock or fire, please strictly abide by the procedures in the operation
manual.
The machine only for the specialized persons, please do not let other people operate.
If any violation of the instructions operation and cause personal injury or machine
damage, our company disclaim all responsibility.
The machine can only maintain by the people who has the certification.

THANKS TO THE BUYER

Great thanks for buying the series of diamond drill of . Please read
operation manual and must pay attention to safety precaution.
The right operation, will make you fully feel our products superior performance.
Please put this manual in a safe place for future reference.

ABOUT THIS MANUAL

The machine model of the description in this manual:

182 182E 202 202E 230 230E 250 250E 300 300E

350 350E 406 406E 450 450E 506 506E

250/2 250/2E 300/2 300/2E 350/2 350/2E 406/2

406/2E 450/2 450/2E 506/2 506/2E

300/3 300/3E 350/3 350/3E 406/3 406/3E 450/3

450/3E 506/3 506/3E

Confirm the machine model according to the nameplate.

1

PRODUCE LVSTRUCTURAL BRIEF INTRODUCTION

1

8

2

3

9

10

11

4

12

a

b

5

6

13

14

c

16

aa

b

17

7

cc

dd

1.Lifted handle

2.Top cover

3.Stator shell

4.Gear case

5.Water circle

6.

Main shaft(a,Metricb,Thick toothc,
Square toothd,Britain makes tooth)

7.Bit
8 .Intermediate cover

9.Square rod

a

15

b

10.Bakelite ball handle

11.Litre reduces ware

12.Rocker

13.Litre reduces ware back shroud

14.Tap

15.Base( a. ordinary b.tape angle)

16.The protector of leakage of electricity

17.Plug（a.China type b.Britain type
c.Europe type ）

2

TECHNICAL PARAMETER

Machine model

182 182E 110/200～ 3980 50-60 ～7"(～182)

202 202E 110/200～ 4280 50-60 ～8"(～202)

230 230E 110/200～ 4580 50-60 ～9"(～230)

250 250E 110/200～ 4880 50-60 ～10"(～250)

300 300E 110/200～ 4980 50-60 ～12"(～300)

350 350E 110/200～ 5280 50-60 ～14"(～350)

406 406E 110/200～ 5580 50-60 ～16"(～406)

450 450E 110/200～ 5680 50-60 ～18"(～450)

506 506E 110/200～ 5780 50-60 ～20"(～506)

250/2 250/2E 110/200～ 4880 50-60 ～10"(～250)

300/2 300/2E 110/200～ 4980 50-60 ～12"(～300)

350/2 350/2E 110/200～ 5280 50-60 ～14"(～350)

406/2 406/2E 110/200～ 5580 50-60 ～16"(～406)

450/2 450/2E 110/200～ 5680 50-60 ～18"(～450)

506/2 506/2E 110/200～ 5780 50-60 ～20"(～506)

300/3 300/3E 110/200～ 4980 50-60 ～12"(～300)

350/3 350/3E 110/200～ 5280 50-60 ～14"(～350)

406/3 406/3E 110/200～ 5580 50-60 ～16"(～406)

450/3 450/3E 110/200～ 5680 50-60 ～18"(～450)

506/3 506/3E 110/200～ 5780 50-60 ～20"(～506)

Specified

voltage

(V)

Rated

power

(W)

Rated

frequency

(Hz)

Corresponding rotational speed

640 100-640

620 100-620

600 100-600

540 100-540

360 100-360

310 100-310

280 100-280

270 100-270

220 100-220

350 100-350 500 100-500

360 100-360 570 100-570

310 100-310 480 100-480

280 100-280 440 100-440

240 100-240 380 100-380

220 100-220 360 100-360

360 100-360 540 100-540 720 100-720

300 100-300 450 100-450 600 100-600

280 100-280 410 100-410 550 100-550

240 100-240 360 100-360 480 100-480

220 100-220 350 100-350 460 100-460

(rpm)

Biggest

drill hole

(mm)

To improve product constantly, our reservation does not need the right of

informingin advance for technical data change.

TECHNICAL CHARACTERISTIC DESCRIBES

Above series drilling machine can only install on frame to use. This machine applies
to the professional personage operating use that has gotten professional trainning ,
carries out drill hole on the materials such as rock, reinforced concrete and pitch
material or take core. The diameter of drill hole exceeds 250 mm, must use high
performance expansion bolt to fix. In geting into the process of cuting , cooling water
flows through ball valve to go through bit , rushes to go to broken bits , is going to at
the same time cool for the knife head of bit( the wet condition that gets into edge.
Diamond bit, it is the pipe form drilling tool of a kind of hollow, when its front the
section piece that welding( or sintering ) go up and contain diamond If be necessary,
cooling water may collect through a kind of special installation (water collector ).

3

SAFE WORKING INSTRUCTION

Pay attention: When use electric tool, to avoid that electric shock is dangerous or
occur fire, please follow safe working instruction surely. Please read earnestly
before manipulator ware , and keep this rules in safe place.

1.Work maintains the working environment with neat place and confused internal
organs to be easy more to arouse accident.
2 Begin work is former, as working environment carries out necessary cleaning, cann´t.

use electric tool in rain, cannot when being near to burn angry local use electric tool.
3 To avoid electric shock, please do not directly contact earthing parts with hand as .
metal pipeline, heating pipeline, stove or coal-scuttle 。
4 Cannot make child be near Please do not let have not received contact line cable or .
the people manipulator ware of professional trainning, please let be unconcerned
people to be far away from working place.
5 Guarantee that tool is stocking and safe. The electric tool that not used should be .
kept in the place that is dryed and is far away from child.
6 Do not make your electric tool overloaded , can develop the fine performance of .
machine fully more in specified load scope.
7 Dress correct protection clothes Cannot wear very confortable clothing or wear .
jewelry, otherwise be twined very much by the revolving part of machine occur
danger. Manipulator ware , suggest to put on ear shield and rubber gloves , wear to
guard against slipper y shoes in enter the plate of long hair safety helmet.
8 If inconvenience. May install machine connection to aspiration. .
9 Cannot use line cable to do other use cannot use line cable to drag Ye machine, can-.
n´t Ye line cable pulls out plug.
10 Cannot over bend waist , avoid that body adopts unusual attitude. Ensure you to .
stand position safety maintains body balance.
11 Please protect your machine properly, in order to make it develop function norma-.
lly when it is working. Please follow working instruction when changing tool. Often
inspect machine from tape line cable , ensure to have no breakage, maintaining h­ andle to be dryed have no oil.
12 Machine does not use for a long time, before defending machine or before chang-.
ing bit, please pull out the plug of power source.
13 Cannot stay in the spanner of handling bit bit is above, before starting machine, e-.
nsure that spanner has left bit.
14 Avoid accident start machine. When moving to put through the machine of power .
source , cannot put finger on switch. Ensure that before plug is being inserted into
socket, machine switch is in the location that stops.
15 In outdoor manipulator ware, please use the cable of extension line that accords .
with safe requirement.
16 In unit process of cargo bandling must notice concentration, do not when excessi-.
veness tiredness, after wine, finish drill with the condition of taking medicine to
make tool.
17 The type of generator speed adjustment or gear speed adjustment in work please .
select the adaptive bit of appearance, and open speed most quickly, so machine
reach best state. If rig in working process rock , must close machine to inspect the
concentric degree of bit and main shaft , can damage machine otherwise to occur
danger.

4

18.Pay attention: For your personal benefit, please choose original factory accessory Is
not original factory accessory if choosing , will may produce injury for operator or
the very machine.

PREPARATORY STAGE

It may use additional tool , is completed in order to go off work to do if please
install and join you according to step for diamond drilling machine.

Pay attention: Before joining , must guarantee that the switch of main
computer is in the state that stops.

Step 1: Comparing with the inspection of container load plan, machine and parts
open package, inspect machine in transportation process, whether damage ,
inspection the voltage of building site whether the voltage that shows on name plate
is consistent, contrast container load plan sees the attachment in package whether is
complete.
Step 2: Power source joins , according to a standard EN61029 and a IEC1029-2 6
of European Union, taking the diamond drilling machine of water schoolwork must
add to pack the protector of leakage of electricity ,the socket of power source must
carry out earthing. It is consistent with these safe rules, our product matches have
packed the protector of leakage of electricity, its function ,including leakage of
electricity are protected untie with under-voltage to deduct. Insert the plug of power
source well after, the switch face plate of the protector of leakageof electricity must
ensure that is in ON ( beginning ) location.Fall if arising voltage drop, the protector
of leakage of electricity will automatic everything breaks , once after voltage normal,
should operate the protector of leakage of electricity again in REST cubes ( reset )
location. The protector of leakage of electricity specified movement current is 30mA.
Pay attention: Quote clean source of water surely , contain grit waiting for until
the water of impurity may damage the water set sealing ring of machine, biggest
hydraulic pressure is 3BAR.
Step 3: Source of water joins , the radom ware additional water inlet of flaxible
tube holds to have " fast joint" may join to wire reinforced suction hose very
conveniently on water supply system.
Pay attention: If the protector function of leakage of electricity is not normal ,
please do not want manipulator ware.
Step 4: Safety is tested , pressing generator switch and machine ( soft start
switch ) start smoothly. Press the protector button of leakage of electricity of " test ",
machine stops operation , then resumes the power supply for machine again
according to the button of " reset ".
Pay attention: Must cannot soak the protector of leakage of electricity in water.
Must often pass according to press TEST button, come to inspect its function whether
is normal. Suggesting operator not to operate do not take the diamond drilling
machine of the protector of leakage of electricity.

5

BEGIN TO OPERATE

1、Choose suitable diamond bit

The main shaft of our company deducts 4 kinds uses type frequently, please ch­oose the reliable diamond bit of quality. Choose sharp tool , And ensure that diam­ond knife is first to have enough backlash( the thickness of knife head the thickness
that is larger than tube wall , such do good to more in row bits) between metal tube
wall. It is above that using waterproof oil paint in the bit to deduct, in order to make
dismantling bit convenient. Ensure bit way jump do not be larger than 1 mm
( eccentricity).

2、Fix frame in face

Regular method has expansion bolts to fix ; vacuum sucker is fixed ; suppor ts
regular etc..
The most general method is fixed for expansion bolt, please use the diameter
of metal expansion bolt and bolt as far as possible, must be larger than 12 mm.
Using vacuum sucker fix , ensure that vavuum pump has enough efficiency,sealing
ring complete have no breakage. Adopting suppor t ensure when fixing way that
frame has enough stability.
Fix using expansion screw regular way, first, will guarantee that face and the
base of machine will be balanced , if have , it is high! Please use the spanner that
takes in machine attachment for low injustice,the 4 adjustment screws on
regulation base are balanced till base. After being fixed completely, machine
should guarantee that generator will not slide on rack . And will make efforts
around around pull to move pillar , will guarantee that when pillar is not around ,
sway side may use machine.
Pay attention: Our company suggests to use expansion bolt regular way to fix
vigorously, and the location of expansion screw lets egg to pillar direction to be
near is best. Since fixing consequence our company that not causes firmly , do not
undertake any duty.

3、Begin drill hole

This rig is let only to have accepted the professional personage of related
trainning to use , may realize the drill hole on the materials such as rock ,
reinforced concrete and pitch or take core. Please carr y out operation surely
according to working instruction.
Pass through ball valve, lead into adequate source of water, so as make broken
bits have been rushed thoroughly, if the mud water mixture that forms fills fully a
machine that get into , you will not lead into adequate source of water. Please give
bit according to requirement with feed pressure,otherwise, diamond l of bit top
may be polished , the efficiency of such drill hole will reduce greatly. Sometimes,
bit knife head may go on open on SIC material it makes bit not to tremble that
edge P asks notice, otherwise the diamond on carcass may drop.
When geting into to cut to meet metal material , please change to use low
speed , and increase feed pressure.When appearance blocks to get into , does not
want in order to open , the way of closing machine comes to go on loose please
close machine at once, it is loose that using spanner to pull around to move bit go
on put aside machine carefully drill hole.

Ver tical upward drill hole, must ensure special turn water to obtain basin , guard
against generator strictly cannot enter water. In working error any suspension, op­en only to star t machine road can. Ensure to take the charge of machine fear start
former bit may turn freely.Is not blocked in hole.

6

FRICTION CLUTCH

Clutch carries out protection under high-strength mechanical overload
condition for operator, machine and bit. Please ensure clutch in a separation state
goes off work to do do not exceed 3-4 second, because it will cause temperature
rise quickly and causes wear for friction flat that time passes length.

MASTER SWITCH AND OVERLOAD PROTECTIVE DEVICE

After pressing switch, machine ( soft star t switch ) starts smoothly.If machine
is overload, its electron protects switch, will remind operator machine to be
overload with exceptional fluctuation. If load does not be reduced , after some
seconds of clocks, switch is closed voluntarily. Star t again if remove load, machine
will again start smoothly. When start machine again is former, ensure bit may turn
freely is not blocked in drill hole. It will even burn out for that generator causes
serious infringement if this machine highest compression is higher than 260 V for
260 V. When using generator to supply power , must notice that voltage peak value
cannot be higher than 260 V.

GEAR SPEED ADJUSTMENT

Ordinary gear speed adjustment Oil soaks money gear speed adjustment

L

M

H

3 files 3 files 2 files2 files

L

H

To improve the efficiency of drilling, some machines have 3 type gear speed chan­ges. In it is high to divide , high speed files ( the day files ) apply to little bit and more
soft material to rush , fast files ( M files ) apply to in bit and more hard material; The
files of low speed ( L files ) apply to big bit and hard material.

Machine turns under stoping the state that turns or stops soon to move group cha­nge files.
Machine must want to shift gear to position when shifting gear , if occur main shaft
after start,it does not turn or have tooth sound to explain that files position does
not hang to position , must close switch at once, and turn again move knob to the
position that needs files at the same time round trip turns main shaft ( hang files
easily ), have obvious put into gear to block until position.
Must close mains switch at once, round trip turns main shaft to at the same time
turn to move knob. Machine is operating at full speed, load or card please don't
change files when living.

M

L L

H H

7

L is the files of low speed, H is high speed files, M is the files of middling speed( 3
files types), graphic representation is the files of low speed, spin along hour hand if
by the files of low speed, turning high speed files knob, other wise counter-clockwise.

OIL SOAK TYPE ADVANTAGE

Oil soak type diamond drilling machine is a kind of can on reinforced concrete, brick
stone, rock, porcelain and fire-resistant material the new tool of drill hole. The equipment
that applies to is installed , water power the constructions such as installation and tunnel ,
installation field. It has very good sealing for liquid oil, that oil soaks the aluminum
processing of high accuracy of money machine, and weather strip produces expansion
force, will not also arise the phenomenon that leaks oil.

OIL SOAK TYPE ADVANTAGE

It may make with high speed revolving gear service life raise the time of 2 a 3 timeses if
oil soaks the liquid oil of money machine, and gear has no noise when occluding.
It has to endure the property with wear-resisting high rotational speed , that oil soaks
the capsulation of money machine. And service life is long.

8

COMMON FAULT AND THE METHOD OF REMOVING

Fault

Generator

does

not

turn

Drill hole

is too

slow

Reason

Power source is obstructed ,
or cont acts to loo sen to fall
Carbo n brush blocks ,
take off open commutator
Af ter the protector movement of
leaka ge of electricity, do not reset
The protector d amage of
leaka ge of electricity

Bit lif e has arrived

Feed pressure is too low

Bit kni fe fir st sur face is pasted
by thin b its

Rotational sp eed is too high

It is sli pper y to cut thick reinforcing
bar to hit

In processing hole, amass bits

Current does not be obeied , leakage
or have no reflux

Bit sha rp degree redu ces

The method of removing

Resume power sourc e , inspect all joints an d tighten

New ins tallation carbon br ush

Press reset button to star t generato r again

Chang e the protector of leakage of elect ricity

Chang e bit

Increase feed press ure

Clean b it, increase hydraulic p ressure

Switch the files position of low speed

Feed pressure reduces is little after,will cross reinforcing

bar increase pressure again

Put in order hole bottom. Pressu rization

Inspe ct into the valve of water polo , inspect current

Using f ire-resist ant brick or emery wheel open edge again

Bit

blocks

Bit wall

wear is

rapid

Water set
leakage

The leather or broken bits piece of
reinforcing bar blocks , i s geting into
core between bit or between bit and
hole wa ll, frame fixes , is not firm , it is
exceptional to produce displacement
frame p illar and the gap of sliding
sleeve.

Main sh aft not just

Bit not j ust

Reinforcing bar or thin bits ca n not
remove hole outside
The skeleton wear or ageing of sealin g
ring

Sto p machine , turn bit around spanner, or pull out bit

to knock broken get into heart to fix the fr ame

adjus tment gap of sliding sleeve again.

Repair or change main shaf t

Chang e bit

Improvement current, take out bit , clean hole

Chang e skeleton sealing ring

9

MAINTENANCE

Pay attention: When carry out machine maintenance is former, must will the plug
of power source of machine breaks open.

Use the rag clean machine , cannot use water to spray to wash , ensure that machine ge­nerator and switch box do not enter water. Ensure that air-breather is unblocked and clean ,
clean the main shaft to deduct and paint oil.

Liquid oil-lubricated gear

After machine amounts to 300 hours of work, professional follows following program

consummately or strictly: Should change gear lubricating oil. It is from authority that please
ensure this work repair station will machine is vertical under ( the dynasty of main shaft ) fix.
Loosen gear case shell goes up3 6 angle screws, take generator and intermediate cover ,
change gear lubricating oil, please use the brand lubricating oil that our company designates.
According to dismantle in proper order new assembly, and it is correct to ensure to install.

Pay attention: If arise the leakage of lubricating oil, close machine immediately ,
will damage gear otherwise.

Water set sealing ring

If cooling water leaks from water place, please change i immediately, the professional

who should repair station by authority by and this work is completed.

Carbon brush

Machine amounts to 300 hours of work afterwards, should inspect carbon brush whether

needs change. All maintenances about generator should be completed by professional.

QUALITY GUARANTEE

In machine 6 months when customer purchases our production , enjoy free
maintenance and regular me but K engages in. When use normally is overall or accessory
occurs pour the product fault that 7 workmanships or components cause , please rely on
receipt original, dealer stamps and fills the proof of good repair to our or our designated
repair station to enjoy free service.
The normal wear of machine fragile , is overload , do not operate according to working
instruction , dismantle independently the damage that causes as well as because of this
use: The damage besides company that accessory causes does not belong to the scope of
good repair. After expiring , good repair offers paid repair service from designated repair
station. Maintenance log must stamp or sign by repair station to just come into effect.

1 0

※Since fixing consequence our company that not causes firmly ,
do not undertake any responsibility!

NO.

Parts name

QTY

NO.

Parts name

QTY

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53

Water seal 40 * 50 * 7
Water Circle 200D
Hose faucet 200-EU
Hegonal screw M5 * 18
Oil seal 40 * 50 * 7
Spindle KF-200
Bearing 6201
Class I tooth shaft 200D-2(15)
Marketing 4 * 10
Class I gear 200D-1(7)
Bearing 6201
O-ring φ 130 * 2
Middle cover 200D
Oil seal 15 * 21 * 3
O-ring φ 35 * 2
Bearing 6201
Nut 200
Iron Ring 200-2
Curved bullet pad 200A
Flesh iron 200A
Separation film 200A
Class II gear 200D-3
Ring 250
Bearing 6201
Class II tooth shaft 200D-4
Card 22
Spindle gear 250-5
Card 24
Cylinder φ 4 * 12
Hegonal screw M6 * 85(half tooth)
Gear box 200D
Bearing 6005
Inner card 47
Hegonal screw M6 * 110(half tooth)
Pad M6
Pad M6
Bearing 6202
Rotor DK-202
Bearing 6201
Breeze 200D
Loose nut M5
Pad M5
Hegonal screw M5 * 105(half tooth)
Interior 200A
Insulation sleeve 200A
Stator DK-202
O-ring φ 38 * 3.1
Business Sign DK
Stator hull 200D
Cross level screw M4 * 8
Parameter card DK(92.5 * 40.3)
Brush frame 200D
Bypass 200A

2
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
2
1
2
1
2
4
4
1
1
1
1
2
2
2
1
2
1
2
1
1
1
1
1
2

54
55
56
57
58
59
60
61
62
63
64
65
66

Round Head Cross Screw M4 * 8(Copper)
Carbon Brush 200A
Cover 200D
Horizontal instrument φ 16 * 8
Hegonal screw M4 * 10
Switch Box 200A-FS
Fold proof connector M16 * 1.5
Button head SKT-10
Hegonal screw M4 * 45
Switching box cover 200A-FS
Electromagnetic switch KJD17B
Power cord 3 * 1.0 * 3.5 M
Leakage protector PD16

2
2
1
1
2
1
1
1
4
1
1
1
1

1 1

DK-202

1 2

NO.

Parts name

QTY

NO.

Parts name

QTY

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53

Water seal 40 * 50 * 7
Hose faucet 200A-EU
Water Circle 250D
Hegonal screw M5 * 18
Water seal 40 * 58 * 8
Oil seal 40 * 55 * 7
Spindle 250A
Bearing 6202
Class II tooth shaft 250A-4(14)
Ball head plunger M8 * 15
Type II High Speed Gear 250A/2 -5
Stop Ring 18
Class II sliding gear 250A/2 -4
Type II low-speed gear 250A/2 -3
Card 16
Bearing 6201
Inner card 52
Bearing 3205
Gear box 250D.
Hegonal screw M6 * 125(half tooth)
Hand-key pad 200A(11)
Separation film 200A
Spindle gear 250A-5(14)
Curved bullet pad 200A
Ring 250
Separation nut 200A
Bearing 6202
O-ring φ 135 * 2
Middle cover 250D
Oil seal 15 * 21 * 3
O-ring φ 35 * 2
Hegonal screw M6 * 135(half tooth)
Pad M6
Pad M6
Cylinder pin 4 * 12
Stop ring φ 40
Cylinder pin 5 * 25
O-ring φ 38 * 3.1
Dialing knob 250D
File plate 250A/2
Flesh iron 200A
Bearing 6201
Class I tooth axis 250A/2 -2
Marketing 4 * 10
Class I gear 250D-1(7)
Bearing 6201
Bearing 6202
Rotor DK-300 / 2E
Bearing 6201
Breeze 200D
Loose nut M5
Pad M5
Hegonal screw M5 * 105(half tooth)

1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
5
1
1
1
1
1
1
2
2
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2

54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83

Interior 200A
Insulation sleeve 200A
Stator DK-300 / 2E
O-ring φ 38 * 3.1
Business Sign DK
Stator hull 200D
Cross level screw M4 * 8
Parameter card DK(92.5 * 40.3)
Fold proof connector M16 * 1.5
Carbon Brush 200A
Round Head Cross Screw M4 * 8(Copper)
Bypass 200A
Brush frame 200D
Cover 200D
Horizontal instrument φ 16 * 8
Hegonal screw M4 * 10
Pad M5
Hegonal screw M5 * 10
Curved handle 200D
Switch Box 200A-T-FS
Button head SKT-10
Switching box cover 200A-T-FS
Hegonal screw M4 * 50(half tooth)
Hegonal screw M4 * 25
Electromagnetic switch KJD17B
Speed adjustment label SCY
Governor SCYRQ DG ZQ-18A
Speed control knob KN-8D
Leakage protector PD16
Power cord 3 * 1.5 * 3.5 M

1
2
1
1
1
1
1
1
1
2
2
2
1
1
1
2
4
4
1
1
1
1
4
1
1
1
1
1
1
1

1 3

DK-300/2E

1 4

NO.

Parts name

QTY

NO.

Parts name

QTY

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53

Water seal 40 * 50 * 7
Hose faucet 200A-EU
Water Circle 250D
Hegonal screw M5 * 18
Water seal 40 * 58 * 8
Oil seal 40 * 55 * 7
Spindle 250A
Bearing 6202
Class II tooth axis 250A/3 -6(14)
Ball head plunger M8 * 15
Type II High Speed Gear 250A/3 -5
Stop Ring 18
Class II sliding gear 250A/3 -4
Type II low-speed gear 250A/3 -3
Card 16
Bearing 6201
Inner card 52
Bearing 3205
Gear box 250D.
Hegonal screw M6 * 125(half tooth)
Hand-key pad 200A(11)
Separation film 200A
Spindle gear 250A-5(14)
Curved bullet pad 200A
Ring 250
Separation nut 200A
Bearing 6202
O-ring φ 135 * 2
Middle cover 250D
Oil seal 15 * 21 * 3
O-ring φ 35 * 2
Hegonal screw M6 * 135(half tooth)
Pad M6
Pad M6
Cylinder pin 4 * 12
Stop ring φ 40
Cylinder pin 5 * 25
O-ring φ 38 * 3.1
Dialing knob 250D
File plate 300A/3
Flesh iron 200A
Bearing 6201
Class I tooth axis 250A/3 -2
Marketing 4 * 10
Class I gear 250D-1(7)
Bearing 6201
Bearing 6202
Rotor DK-300 / 3E
Bearing 6201
Breeze 200D
Loose nut M5
Pad M5
Hegonal screw M5 * 105(half tooth)

1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
5
1
1
1
1
1
1
2
2
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2

54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83

Interior 200A
Insulation sleeve 200A
Stator DK-300 / 3E
O-ring φ 38 * 3.1
Business Sign DK
Stator hull 200D
Cross level screw M4 * 8
Parameter card DK(92.5 * 40.3)
Fold proof connector M16 * 1.5
Carbon Brush 200A
Round Head Cross Screw M4 * 8(Copper)
Bypass 200A
Brush frame 200D
Cover 200D
Horizontal instrument φ 16 * 8
Hegonal screw M4 * 10
Pad M5
Hegonal screw M5 * 10
Curved handle 200D
Switch Box 200A-T-FS
Button head SKT-10
Switching box cover 200A-T-FS
Hegonal screw M4 * 50(half tooth)
Hegonal screw M4 * 25
Electromagnetic switch KJD17B
Speed adjustment label SCY
Speed control knob KN-8D
Governor SCYRQ DG ZQ-18A
Leakage protector PD16
Power cord 3 * 1.5 * 3.5 M

1
2
1
1
1
1
1
1
1
2
2
2
1
1
1
2
4
4
1
1
1
1
4
1
1
1
1
1
1
1

1 5

DK-300/3E

1 6