Cavity Sliders CAVILOCK BARN DOOR STRIKE Installation Instructions Manual
TEMPLATE
STRIKE PLATE/ SHIMS
MOUNTING BRACKET
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
MOUNTING
SCREWS
CAP &
SET SCREW
BASE
DIRECT MOUNT
PASSAGE
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
TEMPLATE
STRIKE PLATE/ SHIMS
PRIVACY/
PASSAGE
KEY
MOUNTING BRACKET
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
TO INSTALL MOUNTING BRACKET:
BOTH JAMB AND DIRECT MOUNT.
NO. 3 PHILLIPS SCREWDRIVER
MOUNTING
SCREWS
CAP &
SET SCREW
BASE
DIRECT MOUNT
STRIKE PLATE/ SHIMS
PRIVACY/
PASSAGE
KEY
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
TEMPLATE
STRIKE PLATE/ SHIMS
PRIVACY/
PASSAGE
KEY
MOUNTING BRACKET
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
TO INSTALL MOUNTING BRACKET:
BOTH JAMB AND DIRECT MOUNT.
NO. 3 PHILLIPS SCREWDRIVER
MOUNTING
SCREWS
CAP &
SET SCREW
BASE
DIRECT MOUNT
NOTE: VERTICAL ADJUSTABILITY
(”I SLIDE”)
USE TEMPLATE TO DRILL PILOT HOLES
FOR MOUNTING SCREWS.
ALIGN TEMPLATE CENTERLINE WITH CENTER OF DEADBOLT
AND EDGE OF DOOR FRAME.
OFFSET STRIKE
OPENING.
JAMB MOUNT USES FIVE SCREWS
(ONE IN DOOR JAMB)
DIRECT MOUNT USES FOUR SCREW.
STRIKE PLATE/ SHIMS
PRIVACY/
PASSAGE
KEY
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
BASE
OFFSET STRIKE
OPENING.
JAMB MOUNT USES FIVE SCREWS
(ONE IN DOOR JAMB)
DIRECT MOUNT USES FOUR SCREW.
STRIKE PLATE/ SHIMS
PRIVACY/
PASSAGE
KEY
MOUNTING BRACKET
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
BASE
DIRECT MOUNT
CAP &
SET SCREW
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
STRIKE PLATE/ SHIMS
PRIVACY/
PASSAGE
KEY
MOUNTING BRACKET
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
BASE
DIRECT MOUNT
TEMPORARILY INSTALL
OFFSET STRIKE
OPENING.
JAMB MOUNT USES FIVE SCREWS
(ONE IN DOOR JAMB)
DIRECT MOUNT USES FOUR SCREW.
1
STRIKE PLATE/ SHIMS
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
BASE
DIRECT MOUNT
TEMPLATE
STRIKE PLATE/ SHIMS
MOUNTING BRACKET
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
MOUNTING
SCREWS
CAP &
SET SCREW
BASE
DIRECT MOUNT
STRIKE PLATE/ SHIMS
MOUNTING BRACKET
JAMB MOUNT
NO. 2 PHILLIPS
SCREWDRIVER
NO. 3 PHILLIPS SCREWDRIVER
CAP &
SET SCREW
BASE
DIRECT MOUNT
CAP &
2. Install Base:
Install base to mounting bracket. Note: vertical
adjustability (”I SLIDE”). Do not tighten screws yet.
Installation Instructions for
CAVILOCK Barn Door Strike
Tools Required:
NO. 2 PHILLIPS
Parts List
HEX
WRENCH
SCREWDRIVER
MOUNTING
SCREWS
NO. 3 PHILLIPS SCREWDRIVER
MOUNTING BRACKET
OR
BASE
Installation
1. Install mounting bracket:
Use template to drill pilot holes for mounting screws.
Align center of semicircle on template with head of
plunger.
STRIKE PLATE/ SHIMS
PRIVACY/
KEY
SET SCREW
PAGE
Ver tic al
adjustment
VERTICAL ADJUSTMENT
(I SLIDE)
(I SLIDE)
Base installed
3. Install Magnet:
Use back two holes for flush striker (Passage/Privacy).
Use front holes for recessed striker (Key Locking).
PASSAGE/
PR IVACY
KEY
4. Temporarily install the strike.
Install strike and shim for Privacy/Passage.
Install strike only for Key.
Offset Strike
Opening
Jamb mount uses five
screws (one in door jamb)
Plunger
Template
Direct mount uses
four screws.
Note: strike is offset and reversible for best fit.
Make vertical adjustment if needed and tighten screws.
(Remove shim and
strike before next step)
Go to page 2
(overleaf)
Installation (continued)
5. Install cap.
Tighten set screw into divot in the back of the base.
(Use 3/32” hex wrench)
Note: installation of the shims and strikes completes
the assemble/retention of the cap.
2
7. Important: set barn door rail stop.
Close door and adjust stop.
Track stop must be set to hit roller before door makes
contact with the strike. The amount varies with each
manufacturer and should be thoroughly tested.
PAGE
Set screw
goes here
Tighten
here
Cap shown installed
without strikes and shims
6. Install shims and strike.
Note: Strike opening is offset and reversible for best fit.
Passage/ Privacy: Install shim and strike.
Key Locking:
Strike is offset and reversible
Drawings are not to scale.
Install strike.
548 Finney Ct
Gardena
CA 90248
© Cavity Sliders USA Inc. CAVILOCK® BARN DOOR STRIKE
(O.D. 2018) 61336 - 02.2019
All copyright and other property in this document is reserved by Cavity Sliders
USA Inc. Details and specifications are subject to change without notice. Whilst
all care is taken to ensure the accuracy of all information, no responsibility will
be accepted for any errors or omissions. ® CAVILOCK is a Registered Trademark.
Patents pending.
T (888) 466 0030
F (310) 769 5824
www.
cavitysliders.com
®
Loading...