Cattron North America 86942 User Manual

2PCA-8694-A001 Radio Module

9S02-8694-A001

Revision: A
Status: Approved
Date: December 10, 2017
Author: H. Lin
Filename: 9S02-8694-A001

This document and all information contained within are the exclusive, confidential and proprietary property of

Laird PLC, Laird Controls North America, Inc., or other subsidiary of Laird PLC (hereafter, “Laird”). It is not to be

reproduced, nor is it or any portion of it to be used by or disclosed to any other individual or legal entity, without

the prior, written approval of Laird. Furthermore, the information contained within this document is also to be

handled in accordance with any and all confidentiality agreements between Laird and the receiver or user of this

document. © Copyright 2017, Laird. All rights reserved.

2PCA-8694-A001 Radio Module

Revision

Date

Name

Notes

A

December 10, 2017

H. Lin

Initial Release

9S21-8694-A001

REVISION HISTORY

Laird™ proprietary and confidential Page 2 of 12 9S02-8694-A001

Revision: A, Approved

2PCA-8694-A001 Radio Module
9S21-8694-A001

TABLE OF CONTENTS

1 INTRODUCTION ....................................................................................................................................................... 7

1.1 PURPOSE ......................................................................................................................................................... 7

1.2 SCOPE............................................................................................................................................................. 7

1.3 APPLICABILITY .................................................................................................................................................. 7

1.4 ACRONYMS, ABBREVIATIONS.......................................................................................................................... 7

2 FEATURES SUMMARY ............................................................................................................................................... 8

2.1 GENERAL ARCHITECTURE ................................................................................................................................... 8

2.2 POWER SUPPLIES AND REGULATORS .................................................................................................................... 8

2.3 FREQUENCY REFERENCE AND PHASE LOCKED LOOP: ............................................................................................... 9

2.4 RECEIVER SECTION: ........................................................................................................................................... 9

3 HOST INTERFACE DEFINITION ..................................................................................................................................10

3.1 PINS ASSIGNMENT ..........................................................................................................................................10

4 TECHNICAL DATA AND SPECIFICATIONS .....................................................................................................................11

LAIRD – WIRELESS AUTOMATION AND CONTROL SOLUTIONS SUPPORT ..................................................................................12

Laird™ proprietary and confidential Page 3 of 12 9S02-8694-A001

Revision: A, Approved

2PCA-8694-A001 Radio Module
9S21-8694-A001

86942TRX module meets Part 90 of the FCC rules and regulations. Compliance with the labeling requirements,
FCC notices is required. In order to comply with FCC Certification requirements, the Original Equipment
Manufacturer (OEM) must fulfill the following requirements.

1. The system integrator must place an exterior label on the outside of the final product housing the 86942TRX
Module. The figure below shows the contents that must be included in this label.

2. 86942TRX modules may only be used with the antennas that have been tested and approved for use with
the module.

LABELING REQUIREMENTS

The OEM must make sure that FCC labeling requirements are met. This includes a clearly visible exterior label on
the outside of the final product housing that displays the contents shown in below.

WARNING: The 86942TRX modules have been tested by the FCC for use with other products without further
certification (as per FCC Section 2.1091). Changes or modifications to this device not expressly approved by
Cattron-Theimeg could void the user’s authority to operate the equipment.

NOTICE: OEM’s must verify the final end product complies with unintentional radiators (FCC Section 15.107 and

15.109) before providing a declaration of conformity for their final product to Part 15 of the FCC Rules.

NOTICE: The 86942TRX modules have been certified for mobile and fixed radio applications. If the module will
be used for portable applications, the device must undergo SAR testing.

RF Exposure WARNING: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.

NOTICE: The preceding statement must be included as a CAUTION statement in OEM product manuals in order
to alert users of FCC RF Exposure compliance.

86942TRX is designed for use in countless wireless applications requiring long range communications with low
energy consumption. To ensure that the final product complies with the all of the regulatory requirements for
the Modular Grant the following integration instructions should be followed. 86942TRX is limited to OEM
installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instructions
to remove or install the module.

Laird™ proprietary and confidential Page 4 of 12 9S02-8694-A001

Revision: A, Approved