Catskill Craftsmen 51531 User Manual
Assembly Instructions
Model 51531
Butcher Block Cart with Backsplash
GENERAL:
1. You have purchased model 51531.
2. Should you need assistance or need to replace a damaged or missing part, simply give us a call M-F at
607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same
day! You may also email us info@catskillcraftsmen.com.
3. Read the assembly instructions and the enclosed brochure before beginning assembly. Assembly is
easy if you read and follow the instructions step by step. See our website www.catskillcraftsmen.com, for
assembly tips and videos.
4. Toots required: Phillips screwdrivers - medium and small, medium at blade screwdriver, a pencil and a
hammer.
CABINET PARTS FOR 51531
Table Top (1)
P/N: TT-51531
TOPTOP
Drawer Bottom (1)
P/N: DB-51531
Right Door (1)
P/N: DOR-51531R
Side Panel (2)
P/N: SP-51531/HL
EDGE BANDING
GOES OUT
Back Panel (1)
P/N: BP-51531
Drawer Side
Left (1)
P/N: DS-51531/L
Drawer Side
Right (1)
P/N: DS-51531/R
Left Door (1)
P/N: DOR-51531L
Middle Shelf (1)
P/N: MS-51531
Bottom Shelf (1)
P/N: BS-51531
Drawer Front (1)
P/N: DF-51531
Drawer Back (1)
P/N: DBK-51531
Drawer Dowel (1)
P/N: DDL-51531
Table Top Stick (2)
P/N: TTS-51531
Bottom Brace (1)
P/N: B-17 1/2-BF-51531
Top Brace (1)
P/N: B-17 1/2-TF-51531
Back Splash (1)
P/N: BSP-51531
Door Spacer (1)
P/N: DOR-21 9/16-51531
HARDWARE FOR 51531
1 3/4” Phillips Flat Head Bolt (8)
(Used to attach
Drawer Front)
Cam Posts (2)
1 1/4” Phillips Flat Head #8 Screw (15)
(Used to attach
Towel Bar/Handle)
Towel Bar Post (4)
1” Phillips Flat Head #8 Screw (4)
(Used to attach
Door Knobs)
1 1/4” Truss Head Machine Screw (2)
(Used to attach
Drawer Handle)
3/4” Truss Head Machine Screw (2)
(Used to attach
Door Spacer)
5/8” Phillips Flat Head #8 Screw (3)
(Brace Pins)
3/4” Long 3/16” DIA. Steel Pin (4)
(Shelf Pins)
1” Long 3/16” DIA. Steel Pin (8)
(Door Pins)
1 1/2” Long 3/16” DIA. Steel Pin (4)
Cam (2)
3/16” Flat Washer (6)
Door Knob (2)
10-24 Hex Nut (8)
5/8 Wooden Disk (8)
Drawer Handle (1)
Magnet Pack
1/2” Phillips Flat
Head #4 Screw (1)
5/8” Pan Head Screw (2)
Magnet Plate (1)
Magnet (1)
Caster Socket (4)
Towel
Bar (2)
Non-Locking Wheel Caster (2) Locking Wheel Caster (2)
STEP 1
A. Tap/insert one 1 1/2” pin into
each end of both doors. DON’T
OVERDRIVE PINS! Pins should
stick up about 1/2” when seated.
B. Attach the door spacer to the
left door with 5/8” #8 screws. The
spacer has a space at the top to
allow magnet clearance and is
almost ush with the bottom of
the door.
C. Attach the magnet plate (may
be stuck to the magnet!) with the
small at head screw to the top
of the right door. Bumps toward
wood.
D. Attach door knobs with two
1 1/4” truss head bolts.
1 1/2” Pin
5/8” #8 Screw
1/2” #4 Screw
ILLUSTRATION 1
4 used in
this step
1 1/2” Long 3/16” DIA. Steel Pin
2 used
in this step
1 1/4” Truss Head Bolt
Magnet Plate (1)
5/8” Phillips Flat Head #8 Screw
1/2” Phillips Flat Head #4 Screw
STEP 2
Take the 2 front braces and tap/insert one 3/4” steel pin into each
of both braces until seated. About 3/8” will stick out when seated.
OK if loose.
4 used in this step
3 used in this step
1 used in this step
3/4” Pin
3/4” Long 3/16” DIA. Steel Pin
ILLUSTRATION 2
Loading...