Page 1
Assembly Instructions
Model 51526
Microwave Cart
GENERAL:
1. You have purchased model 51526.
2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at
607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same
day! You may also email us info@catskillcraftsmen.com.
3. Read the assembly instructions and the enclosed brochure before beginning assembly. Assembly is
easy if you read and follow the instructions step by step. See our website for assembly tips and videos.
4. The only tools needed are a hammer, a small and a medium Phillips head screwdriver and a medium at
blade screwdriver. A pencil is also needed. A power screwdriver will speed assembly, but is not required.
Place a few drops of vegetable oil on the threads of wood screws before screwing into the solid hardwood
parts.
5. Glides are sometimes pre-packed with screws. These are not used.
Page 2
CABINET PARTS 51526
TOPTOP
TOP
Not used if present
Drawer Side Left (1)
P/N: DS - 51526/L
Drawer Side Right (1)
P/N: DS - 51526/R
Handle Side Panel (1)
P/N: SP HDL - 51526
Cabinet Top (1)
P/N: TT - 51526
Not Used
Bottom Brace (1)
P/N: BB - 51526
Plain Side Panel (1)
P/N: SP PL - 51526
Back Panel (1)
P/N: BP - 51526
13 3/8”
Edge Banded
Middle Shelf (1)
Drawer Front (1)
P/N: DF - 51526
Drawer Bottom (1)
P/N: DBOT - 51526
13 13/16”
Bottom Shelf (1)
Glide Support Sticks (2)
Left Door (1)
P/N: DOR - 51526L
Door Spacer (1)
P/N: DORS - 51526
P/N: GLD SUP - 51526
Right Door (1)
P/N: DOR- 51526R
Not Used
Drawer Back (1)
P/N: DBK - 51526
RACK PARTS
Rack Top (1)
P/N: RKTP - 51526
Top Brace (1)
P/N: TOP BRACE - 51526
Rack Side Panels (2)
P/N: RKSP - 51526
Page 3
CABINET HARDWARE 51526
Drawer
1 3/4” Phillips Flat Head Bolt (8)
(Used to attach
Drawer Front)
Cam Posts (2)
1 1/4” Phillips Flat Head #8 Screw (20)
(Used to attach
Drawer Handles)
7/8” Truss Head Machine Screw (6)
(Used to attach cabinet
glides & “L” Brackets)
5/8” Phillips Flat Head #7 Screw (12)
(Used to attach
Towel Bar)
1” Phillips Flat Head #8 Screw (2)
(Brace Pin)
3/4” Long 3/16” DIA. Steel Pin (4)
(Shelf Pin)
1” Long 3/16” DIA. Steel Pin (8)
3/16” Flat Washer (4)
10-24 Hex Nut (8)
Caster Socket (4)
Cabinet
14” Drawer Glide (1 Set )
5/8 Wooden Disk (8)
Nickel Handle (3)
Towel Bar Post (2)
Cam (2)
(Door Pin)
1 1/2” Long 3/16” DIA. Steel Pin (4)
MAGNET PACK
Magnet (1)
Magnet Plate (1)
5/8” Pan Head Screw (2)
1/2” Phillips Flat Head
#4 Screw (1)
Locking Wheel Caster (2)
“L” Bracket (4)
Non-Locking Wheel Caster (2)
Polished
Nickel Towel
Bar (1)
Page 4
STEP 1
1. Attach the Rack Top to the top ends of the Side Panels (universal: same left/right & top/bottom)
using 1 1/4” #8 wood screws. MAKE SURE YOU HAVE THE RACK TOP! The only difference
between the Rack Top and the Cabinet Top is that the Cabinet Top has 4 small pilot holes on the
bottom side plus the 4 through holes; whereas, the Rack Top only has the 4 through holes.
NOTE: On the Rack Top the countersunk (reamed out) through holes face up and the countersunk
holes/pilot holes on the Cabinet Top face down. The countersunk holes allow the screw heads to be
ush with the wood surface when tightened down.
2. Turn this assembly upside down so that the Rack Top is on a smooth at surface. Attach the
Cabinet Top with four 1 1/4” #8 wood screws. With the unit upside down at this point, the 4 pilot holes
should be up. See illustration 1B.
3. Leave this assembly UPSIDE DOWN and go to STEP 2.
NOTE: The cart cabinet will be constructed upside down
using the bottom of the Cart Top as the base.
8 Used in this step
1 1/4” Phillips Flat Head #8 Screw
CABINET TOP
RACK TOP
ILLUSTRATION 1A
RACK TOP
ILLUSTRATION 1B
CABINET TOP
PILOT HOLES HIDDEN
Page 5
STEP 2
PT
5/8” #7 Screw
Note: The side panels are interchangeable at this point. Drawer glides will determine left or right
sides. Choose at this point if you want the towel bar/handle on the left or right panel. We are using the
left side for these instructions. Cover photo shows towel bar/handle on right side.
A. Attach a Glide Support Stick to the top of each Side Panel using 1 1/4” #8 screws. The Sticks
should be ush with top of panel.
B. Attach the cabinet glide of the Drawer Glides to the Glide Support Stick using 5/8” #7 at head
screws. Left glide to left Side Panel, right glide to right Side Panel. The glides look almost alike
however, the right glide (as you face the cart) has a rolled lip at the top of the glide that keeps the
drawer glide wheel in place. Line up the holes in the glides so that the end with the wheel comes ush
with the front edge of the Glide Support Stick.
C. Attach the “L” brackets to the top of the glide supports using 5/8” #7 screws. Use the long slot
rather than hole/slot. The hole will be used to attach the table top. The “L” brackets should be ush
with the top of the glide support sticks.
Note: Cabinet drawer glides usually have an imprint “CL” or “CR” inside near the wheel.
CR=Right / CL=Left
1 1/4” #8 Screw
TO
LEFT SIDE
OP
5/8” #7 Screw
RIGHT SIDE
Page 6
STEP 3
A. Lay Back Panel at on a smooth surface with holes up.
B. Attach Side Panels with 1 3/4” bolts and hex nuts. After inserting bolts(s) thru the holes in the Side
Panels, thru the holes in the long edges of the Back Panel, place a hex nut on the tip of your nger,
align nut with bolt and tighten.
C. Look ahead to step 5 which shows side panels attached to back panel.
NOTE: Make sure you position the side panels according to Drawer Glides (left or right).
STEP 4
STEPS 5 - 14 WILL BE ACCOMPLISHED WITH
THE UNIT TOP UPSIDE DOWN (INVERTED),
BUILDING UPWARD TOWARD THE BOTTOM/
CASTER END! BE CAREFUL AS PART
DESCRIPTIONS ARE BASED ON AN UPRIGHT,
COMPLETED UNIT!
Mark a Large (X) mark over each of the 4 pilot holes
in the bottom. Make marks about 1 1/2” long. These
marks will help you align the cabinet with the pilot
holes in step 5.
Page 7
STEP 5
A. Turn the side/back assembly (from step 1) upside down (invert) on top of the inverted table top.
B. Using the (X) marks from step 4 as a guide, insert the tips of the 5/8” #7 screws through the slots
in “L” bracket and into the pilot holes in the unit top and nger tighten. When all 4 screws are properly
aligned, tighten down.
C. Tap two 1” pins into each side panel. These pins will hold the bottom shelf.
(Used to attach
“L” brackets)
5/8” Phillips Flat Head #7 Screw
4 Used in this step
1” Long 3/16” DIA. Steel Pin
PIN
PIN
Page 8
STEP 6
A. Attach the drawer back to the drawer sides with four
1 1/4” #8 screws. Make sure parts are aligned
as in illustration 6A.
B. Insert drawer bottom into the slots in the drawer
sides, best side to inside of drawer. Slide down until
seated in the slot in the drawer back. See illustration 6B.
C. Screw the cam posts into the two outside holes on
the inside face of the drawer front until seated. Only
3/8” of the post goes into the wood, leaving the 4 larger
guide rings/head exposed. See illustration 6C. Visit us
at www.catskillcraftsmen.com to view our cam video.
D. Insert the posts into holes in the drawer sides until
seated against the front end of the drawer sides. Insert
cams so that slot in the cam ts over the post and turn
with Phillips screwdriver until seated. Don’t over-torque!
See illustration 6D. See our video online at
www.catskillcraftsmen.com
E. Attach drawer handle with two 7/8” Truss Head
screws each. (no illustration).
F. Attach drawer glides to drawer sides using
5/8” #5 screws. See illustration 6E
ILLUSTRATION 6A
ILLUSTRATION 6B
ILLUSTRATION 6C
Below line in wood
Cam Posts (2)
4 used
in this step
1 1/4” Phillips Flat Head #8 Screw
2 used
in this step
7/8” Truss Head Machine Screw
2 used
in this step
Cam
4 used
in this step
5/8” Phillips Flat Head #5 Screw
ILLUSTRATION 6D
ILLUSTRATION 6E
Page 9
STEP 7
Take the 2 front braces and tap/insert one 3/4”
steel pin into each end of both braces until seated.
About 3/8” will stick out when seated. Ok if loose.
4 used in this step
3/4” Long 3/16” DIA. Steel Pin
STEP 8
A. Take the top front brace (with magnet block),
insert the pins in the brace ends into the slots on
the inside of the front legs and slide down until the
brace aligns with the bolt hoes as illustrated. The
pin holes for the door pins and the magnet block
will be up. Secure with 1 3/4” bolts/nuts.
Insert Brace Pins Here
Hex Nut
Inside Brace
Side Panel Leg
Countersunk Hole in Leg
( disk goes in this hole to
hide bolt head! )
Nut Access Hole
Glide Support
Assembly
1 3/4” #8 Bolts
2 used
in this step
10-24 Hex Nut
2 used in
this step
1 3/4” Phillips Flat Head Bolt
Page 10
STEP 9
Attach handle/towel bar to side panel with 1” #8 screws/washer
from inside one panel.
2 used in this step
1” Phillips Flat Head #8 Screw
STEP 10
A. Tap/insert ONE 1 1/2” pin into
each end of both doors. DON’T
OVERDRIVE PINS! Pins should
stick up about 1/2” when seated.
B. Attach the doorspacer to the
left door with 5/8” #8 screws. The
spacer has a space at the top to
allow magnet clearance and is
almost ush with the bottom of the
door. Countersunk holes out.
C. Attach the magnet plate (may
be stuck to magnet! ) with the 1/2”
#4 screw to the top of the right
door. Bumps go toward the wood.
2 used
in this step
3/16” Flat Washer
D. Attach door handles with 7/8”
truss head machine screws.
4 used in
this step
1 1/2” Long 3/16” DIA. Steel Pin
2 used
in this step
7/8” Truss Head Machine Screw
Magnet Plate
3 used in this step
5/8” Phillips Flat Head #8 Screw
1 used in this step
1/2” Phillips Flat Head #4 Screw
Page 11
STEP 11
A. Install doors by inserting pins in
the door tops into the holes in the
long edge of the top front brace.
B. Place one washer on each of
the door pins in the door bottoms.
C. Take the bottom front brace,
align pins in the door bottoms with
holes along top long edge of brace
(are washers on pins?) and secure
brace with 1 3/4” bolt/hex nuts as
before.
2 Used
in this step
10-24 Hex Nut
2 Used
in this step
3/16” Flat Washer
1 3/4” Phillips Flat Head Bolt
2 Used in this step
STEP 12
A. Stick magnet to magnet plate on right door.
B. With left door open, close the right door. The magnet should be positioned over the wooden block
on the bottom of the top front brace. Hold the magnet in place with your thumb, and open the right
door. The magnet will be in the correct position on the block.
C. Secure magnet with the two round head screws in the magnet packet. Center screws in the slots in
the magnet. This will allow adjustment later, if needed.
NOTE: No pilot holes in block as softwood!
2 Used
in this step
5/8” Pan Head Screw
Magnet
Page 12
STEP 13
A. Insert and tap caster sockets with hammer
until the teeth grab the wood. DON’T POUND
SOCKET FLAT OR CASTER SHAFT WILL
NOT ENTER.
B. Insert casters and seat by pushing straight
downward with heel or your hand, or tap into
place with a hammer. Don’t be afraid to give
them a good downward whack on the solid
metal part of the caster!
C. Locking wheels usually go on front.
STEP 14
A. Upright Unit. Take bottom shelf
(no edge banding) and place it on
the set of back pins. Close doors and
shelf will drop into place.
B. Decide on position of middle
shelf, then tap two 1” pins into each
side panel, making sure the pins on
both sides are in the same relative
position. To remove a pin, use
pliers or claw hammer.
C. Place middle shelf, edge banding
out, on pins.
D. Insert drawer. If drawer front hits
the bottom of the cabinet tap on the
top front brace or tap top front brace
down. Loosten bolts as necessary.
When drawer moves freely,
retighten all bolts!
E. Tap wooden disks into sides.
Page 13
For continued beauty and long life of your
Catskill Craftsmen cart, we recommend
Catskill Craftsmen’s Butcher Block Oil.
Our Butcher Block Oil is available directly from Catskill Craftsmen’s factory. For
one eight ounce (8 . oz.) bottle, which
is sufcient for two applications, simply
send $6.95 along with the completed
coupon to the address below. Visit us
online at www.catskillcraftsmen.com to
browse our assortment of butcher block
care products. Visa and Mastercard are
accepted online .
BUTCHER BLOCK OIL COUPON
Please send me______# of bottle(s) of the
Catskill Craftsmen Butcher Block Oil at $6.95
per bottle. My check or money order is
enclosed for a total of $____________.
Item code: 51526
Name _______________________________
Address _____________________________
City ________________________________
State ___________ Zip ________________
Catskill Craftsmen, Inc.
15 West End Ave.
Stamford, NY 12167-1296
Please make checks payable to Catskill Craftsmen
Inc. 15 West End Ave., Stamford, NY 12167-1296
Loading...